Sized to fit non-UL Class Midget Fuses, these fuse blocks are suitable for switchboard panels, small motors, and transformers. The covered terminals prevent contact with live electrical circuits.

For technical drawings and 3-D models, click on a part number.

Designed for the solar industry, these fuse blocks can handle the requirements of high-voltage DC applications. The covered terminals prevent contact with live electrical circuits.

For technical drawings and 3-D models, click on a part number.

Fuse blocks have a universal hole pattern, so they can be mounted on either DIN-rail or directly onto surfaces.

For technical drawings and 3-D models, click on a part number.

Add as many circuits as you need with these terminal blocks and accessories. The terminal blocks clip onto DIN 3 rail and can be removed without disrupting adjacent blocks. Some also clip onto DIN 1 rail. All have screw-clamp terminals for a secure connection, reducing the chance of wire disconnecting due to vibrations, pulls, or snags. Rated UL 94 V-0, all meet flammability standards. Blocks that meet IP10 shield connections from objects larger than your hand; those that meet IP20 protect against objects larger than your fingers.

Grounding terminal blocks facilitate grounding circuits by electrically connecting wires to DIN rail. They shouldn’t be used for applications other than grounding.

Blocks with a fuse holder protect components and wire from short-circuit damage by enclosing the fuse.

Blocks with a blown fuse indicator light up so you’ll know if your fuse is blown without having to touch equipment or disconnect power.

Blocks with a disconnect tab or knob easily disconnect a circuit without needing to remove installed wire. Use them for testing. Disconnect knobs have a push-button with a through hole, so they can be sealed with wire when they’re disconnected, similar to a lockout tag. This reduces the risk of accidentally connecting the circuit. A test socket lets you try out your circuit. Insert a test plug (sold separately) into the socket, then use a voltage meter to check.

Blocks that are 51.5 mm or 63.5 mm high have a single circuit with multiple screw-clamp terminals, so they save space on DIN rail.

End covers fit on the open side of a block to prevent accidental contact with a live circuit.

End stops mount at the end of a group of blocks to keep them in place. Those rated IP20 provide additional protection from objects larger than your fingers.

Jumpers connect circuits between blocks to simplify wiring and leave terminals available to connect equipment. Blocks must be adjacent to each other and the same width. Bar jumpers screw down into designated sections on terminal blocks. You can cut them to size. Where listed, end covers should be used on the outermost blocks in the connection. Lateral jumpers are connected to blocks in place of a wire or in addition to a wire at the screw-clamp connection terminal points. Insulated jumpers eliminate the risk of your finger coming into contact with a live circuit, so they’re touch safe.

Marker cards fit into built-in label holders on the blocks.

For technical drawings and 3-D models, click on a part number.

No need to tighten or loosen any screws—these terminals lock your wiring in place with spring clamps. Insert a slotted screwdriver to release the spring clamp and then push your wire into place. Spring-clamp wire connections withstand vibration and temperature changes. You can add as many circuits as needed with these terminal blocks and accessories; blocks mount side-by-side on DIN 3 rail.

Rated UL 94 V-0, all meet flammability standards.

Blocks with a fuse holder protect components and wire from short-circuit damage by enclosing the fuse.

Blocks with a blown fuse indicator light up so you’ll know if your fuse is blown without having to touch equipment or disconnect power.

End covers fit on the open side of a block to prevent accidental contact with a live circuit.

End stops mount at the end of a group of blocks to keep them in place.

Jumpers connect circuits between blocks to simplify wiring and leave terminals available to connect equipment. Adjacent jumpers connect terminals on adjacent blocks of the same width. Marker cards fit into built-in label holders on the blocks. Numbered marker cards include two of each number (1-50).

For technical drawings and 3-D models, click on a part number.

Quickly troubleshoot or change wiring without any tools. These terminal blocks have a lever clamp that you flip up to insert wiring and flip down to lock it in place. For more permanent connections, they also have one or two spring-clamp terminals. You’ll need a slotted screwdriver to release the spring clamp that holds the wire in place. All wire connections stand up to vibration and temperature changes. Add as many circuits as you need with these blocks and accessories. The blocks mount side-by-side on DIN 3 rail.

Rated UL 94 V-0, all meet flammability standards.

Grounding terminal blocks facilitate grounding circuits by electrically connecting wires to DIN rail. They shouldn’t be used for applications other than grounding.

End covers fit on the open side of a block to prevent accidental contact with a live circuit.

End stops mount at the end of a group of blocks to keep them in place.

Jumpers connect circuits between blocks to simplify wiring and leave terminals available to connect equipment. These jumpers are lateral jumpers, so they connect to blocks in place of wire or in addition to a wire at the terminal connection points.

Marker cards fit into built-in label holders on the blocks.

For technical drawings and 3-D models, click on a part number.