McMaster-Carr logo
    Filter by
    Anvil Tip Shape
    Spindle Tip Shape
    Display Type
    System of Measurement
    Anvil Face Diameter
    Measuring Increments
    Digital Display Type
    Manufacturer
    Distance Measured
    Thimble Type
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Spindle Diameter
    Container Type
    Frame Material
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Anvil Face Material
    Micrometer Type
    Spindle Face Material
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    15 Products

    Outside Micrometers for Thin Materials

    Image of Product. Front orientation. Outside Micrometers. Outside Micrometers for Thin Materials.
    Avoid ripping and wrinkling paper-thin materials as you measure. The disc-shaped ends distribute pressure over a wide area to prevent denting. Plus, the spindle extends without twisting, so it won't tear delicate parts such as foil.
    To find your exact measurements, read the scales on the sleeve and thimble. These micrometers are free of electronic components that could break if dropped or short-circuit if wet. You don't have to replace any batteries, so they're always ready for the job.
    Mitutoyo—The go-to for machinists and engineers. Every part is made within a Mitutoyo automated factory and tested in-house in Japan. The spindle glides as you turn the thimble with a weighty, silky-smooth feel.
    Ratchet-Stop Thimble—Best for consistent, repeatable measurements. The spindle stops extending the moment it reaches your part, so it won’t overtighten. Hear and feel a satisfying click that confirms you’ve applied the right amount of pressure.
    Outside
    Micrometers
    Measuring
    Range
    Accuracy
    Measuring
    Increments
    Thimble
    Type
    Throat
    Dp.
    Frame
    Material
    Mfr. Model
    No.
    Each
    Mitutoyo
    0" to 1"±0.0002"0.001"Ratchet Stop0.984"Cast Iron169-103-106336N110000000
     

    Digital Outside Micrometers for Gears

    Image of Product. Front orientation. Outside Micrometers. Digital Outside Micrometers for Gears.
    Quickly read gear measurements to make sure they will fit perfectly in your system. The anvil and spindle have flat discs that squeeze between tight gear teeth, where most micrometers can't reach.
    With an LCD display, these micrometers give instant measurements—no need to read scales. Swap between inch and metric or set the position to zero, all with the press of a button. You don't need to reset the zero point since they retain their position when turned off, also known as absolute (ABS) positioning.
    Mitutoyo—The go-to for machinists and engineers. Every part is made within a Mitutoyo automated factory and tested in-house in Japan. The spindle glides as you turn the thimble with a weighty, silky-smooth feel.
    With SPC Data Output—Send measurements to a computer or data processor to store, analyze, and manage data. You'll need a data cable or SPC wireless transmitter and receiver.
    Calibration Certificate—Choose these micrometers when precision measurements are required for quality control or by regulation. The certificate is traceable to NIST, so you can be confident your measurements are correct and consistent.
    Ratchet-Stop Thimble—Best for consistent, repeatable measurements. The spindle stops extending the moment it reaches your part, so it won’t overtighten. Hear and feel a satisfying click that confirms you’ve applied the right amount of pressure.
    Measuring
    Range
    Accuracy
    Measuring
    Increments
    Outside
    Micrometers
    Outside Micrometers with
    Calibration Certificate
    Inch
    Metric,
    mm
    Inch
    Metric
    Inch
    Metric,
    mm
    Thimble
    Type
    Throat
    Dp.
    Frame
    Material
    Measuring Functions
    Mfr. Model
    No.
    Each
    Each
    Mitutoyo
     
    With SPC Data Output
    0" to 1"0 to 25.4±0.0002"±0.005 mm0.00005"0.001Ratchet Stop1"Cast IronZero-Position Memory (ABS)323-350-3220485A88000000020485A890000000
     
    Accessories and Replacements for Outside Micrometers
    Mitutoyo Cords
    Image of Product. Front orientation. Contains Inset. Mitutoyo Cords. Mitutoyo Data Out Switch B × 10-Pin Mitutoyo Connector.
    Image of Product. Front orientation. Contains Inset. Mitutoyo Cords. Mitutoyo Data Out Switch B × USB-A.

    Mitutoyo Data Out Switch B ×

    10-Pin Mitutoyo Connector

    Mitutoyo Data Out Switch B × USB-A

    USB-A Connection—Plug micrometers with SPC data output directly into your computer.
    10-Pin Mitutoyo Connector—Connect micrometers with SPC data output to a Mitutoyo miniprocessor or multiplexer.
    Connection
    Lg.
    Each
    Mitutoyo
    Mitutoyo Data Out Switch B × 10-Pin Mitutoyo Connector40"20395A830000000
    Mitutoyo Data Out Switch B × 10-Pin Mitutoyo Connector80"20395A84000000
    Mitutoyo Data Out Switch B × USB-A80"2429N2000000
     
    SPC Wireless Transmitters
    Image of Product. Front orientation. Contains Inset. SPC Transmitters. Mitutoyo Data Out Switch B Connection.

    Mitutoyo Data Out Switch B

    Connection

    Wirelessly send measurements from micrometers with SPC data output to your computer. You'll also need a receiver.
    Electrical Connection
    Mfr.
    Series
    Each
    Mitutoyo Data Out Switch BU-WAVE-T2424N20000000
    SPC Wireless Receivers
    Image of Product. Front orientation. SPC Receivers.
    Wirelessly send measurements from micrometers with SPC data output to your computer. You'll also need a transmitter.
    Electrical
    Connection
    For Mfr.
    Series
    Each
    Mitutoyo
    USB-AU-WAVE-T2412N10000000
     
    Replacement Batteries
    Each
    1-9
    10-49
    50-Up
    Replacement SR44 Silver Oxide Battery7604K117000000000000000

    Outside Micrometers for Gears

    Image of Product. Front orientation. Outside Micrometers. Outside Micrometers for Gears.
    Measure gears so they fit perfectly in your system. The anvil and spindle have flat discs that fit between tight gear teeth, where most micrometers can't reach.
    To find your exact measurements, read the scales on the sleeve and thimble. You don't have to replace any batteries, so these micrometers are always ready for the job.
    Mitutoyo—The go-to for machinists and engineers. Every part is made within a Mitutoyo automated factory and tested in-house in Japan. The spindle glides as you turn the thimble with a weighty, silky-smooth feel.
    With Analog Display—Watch the display update as the spindle moves for easy-to-read, trustworthy measurements.
    Calibration Certificate—Choose these micrometers when precision measurements are required for quality control or by regulation. The certificate is traceable to NIST, so you can be confident your measurements are correct and consistent.
    Ratchet-Stop Thimble—Best for consistent, repeatable measurements. The spindle stops extending the moment it reaches your part, so it won’t overtighten. Hear and feel a satisfying click that confirms you’ve applied the right amount of pressure.
    Outside
    Micrometers
    Outside Micrometers with
    Calibration Certificate
    Measuring
    Range
    Accuracy
    Measuring
    Increments
    Thimble
    Type
    Throat
    Dp.
    Frame
    Material
    Mfr. Model
    No.
    Each
    Each
    Mitutoyo
     
    With Analog Display
    0" to 1"±0.0002"0.001"Ratchet Stop1"Cast Iron223-1258655A1100000008655A120000000
     

    Mitutoyo Inside Hole Micrometers for Grooved Surfaces

    Image of Product. Front orientation. Inside Hole Micrometers. Mitutoyo Inside Hole Micrometers for Grooved Surfaces.
    Image of Attribute. Front orientation. Contains Annotated, Border. For Grooved Surfaces. Mitutoyo.
    Reach into bores to measure the precise size and location of grooves. These micrometers have two discs on their measuring spindle to find a groove’s edge. Slide the spindle into your bore, press the discs against the wall and into the groove, and twist the thimble to measure the distance between the two discs. A speeder knob moves the measuring spindle more quickly toward or away from your groove, without turning the thimble repeatedly. When the spindle touches the groove you’re measuring, it will stop tightening, but the speeder knob will continue turning with a clicking sound. The spindle doesn’t rotate, so the contact points won’t spin or slip out of a groove.
    Measuring
    Range
    Inside Lg.
    Outside
    Lg.
    Accuracy
    Measuring
    Increments
    Material
    Overall
    Lg.
    Mfr. Model
    No.
    Each
    Ratchet-Stop Thimble—Nonrotating Spindle
    0.055" to 1.05"0" to 1"±0.0004"0.001"Steel
    		9 1/2"146-2325556N110000000
    1.05" to 2.05"1" to 2"±0.0004"0.001"Steel
    		9 1/2"146-2335556N12000000
    2.05" to 3.05"2" to 3"±0.0004"0.001"Steel
    		9 1/2"146-2345556N13000000
    3.05" to 4.05"3" to 4"±0.0004"0.001"Steel
    		9 1/2"146-2355556N14000000
     
    back to top