A raintight NEMA 3R rated enclosure protects these switches from falling liquids and light splashing. The enclosure is steel, so it withstands tougher conditions than plastic enclosures. All have quick-make/quick-break action to eliminate arcing and prolong switch life. They have a lockout to secure in the off position using a padlock (not included).

Use switches with a fuse holder where overload protection is needed. When used with UL Class RK1, RK5, or T fuses, they require rejection-style fuse clips. Note: Horsepower ratings are based on time-delay fuses installed.

Switches with safety interlock keep the door closed when the switch is on, and prevent the switch from turning on when the door is open.

For technical drawings and 3-D models, click on a part number.

Rated IP66, these switches are protected from washdowns. They cut power and keep it isolated to prevent equipment from starting up during inspection and maintenance.

Switches with lockout secure in the off position with a padlock with a maximum shackle diameter of 5/16” (not included).

Add auxiliary contact blocks to send a signal or connect to another device, such as an alarm or indicating light.

Use additional power poles to control more than three circuits. Add neutral poles to open and close the neutral leg of a three phase system.

For technical drawings and 3-D models, click on a part number.

Cut power and keep it isolated to prevent equipment from starting up during inspection and maintenance. These switches are housed in a protective enclosure.

Switches with lockout secure in the off position with a padlock with a maximum shackle diameter of 5/16” (not included).

Add auxiliary contact blocks to send a signal or connect to another device, such as an alarm or indicating light.

Use additional power poles to control more than three circuits. Add neutral poles to open and close the neutral leg of a three phase system.

For technical drawings and 3-D models, click on a part number.

These small disconnect switches are sized to fit in tight spaces but can handle comparable electrical loads to standard sized switches. They cut power and keep it isolated to prevent equipment from starting up during inspection and maintenance. All have a lockout so you can secure them in the off position with a padlock (not included). They’re rated IP65 for protection from washdowns.

For technical drawings and 3-D models, click on a part number.

Install these switches inside an enclosure to prevent it from opening when power is on—turn the switch to disconnect power and release the door. Cut the shaft to fit the enclosure. Use a padlock (not included) to lock switches in the off position. Mount to DIN rail inside an enclosure; mounting depth is the distance from the panel door to the DIN rail. UL listed, C-UL listed, and CE marked, these switches meet American, Canadian, and European safety standards.

Use optional sealing gaskets in washdown environments; they create an IP65 rated seal around the actuator.

Add auxiliary contact blocks to send a signal or connect to another device, such as an alarm or indicating light.

Use additional power poles to control more than three circuits. Add neutral poles to open and close the neutral leg of a three phase system.

Add junction blocks to connect a ground wire.

Terminal covers prevent contact with live terminals.

If there’s a power outage, flip the toggle for each circuit on these switches to backup power. Each circuit can also be turned off completely. To prevent injury and damage to your generators, they are open transition, meaning the contacts disconnect from one power source before connecting to another. This is also known as break-before-make switching.

Use them with a portable generator.

NEMA 1 switches should be used indoors. Those with a power inlet box create a connection point between the switch and a portable generator. The inlet box is rated NEMA 3R, so it can be mounted on the outside of an exterior wall.

NEMA 3R switches can be used outdoors since they seal out rain, snow, and sleet.

Switches with a key lock prevent unauthorized changes to the switch.

When the microcontroller inside detects a power outage, these switches automatically fire up a backup generator. They’ll switch back to utility power once power is restored. To prevent injury and damage to your generator, they are open transition, meaning the contacts disconnect from one power source before connecting to another. This is also known as break-before-make switching. These switches also have built-in overload protection, so they can isolate themselves from utility power to protect your facility. LED status lights let you know which power source is in use. Add a padlock (not included) to the lockout to prevent unauthorized changes to the switch. Rated NEMA 1, these switches should only be used indoors.

They're compatible with generators that have a two-wire remote starting system.

NEMA 3R doors make these switches safe for use outdoors since they seal out rain, snow, and sleet. These doors cover the LED status lights on the switch when closed.

For technical drawings and 3-D models, click on a part number.