We will reply to your message within an hour.
More
Also known as stop cocks, install these valves on your tank for easy draining of air or fluid.
Empty fluid from tanks in boiler rooms or heat transfer systems—these valves withstand higher temperatures than our other drain valves. Also known as stop cocks.
Automatically remove condensate from compressed air or inert gas lines—these float valves have a float-operated drain control.
Smaller than other float valves, these are sized for containers with limited space.
Control water levels in spaces where a rod and lever won’t fit; these float valves have an internal float and connect to your pipe.
Use these float valves with water.
Able to withstand higher temperatures than PVC float valves, these valves have a temperature range of 35° to 175° F.
These float valves have a temperature range of 35° to 110° F.
Combine these float valve bodies with floats and rods to create float valves that meet exact specifications.
Set the electronic timer on these drain valves to open automatically at your specified time interval.
These withstand at least double the pressure of our other timer-operated drain valves.
Use the digital display to set these valves to open automatically at precise intervals.
Able to withstand up to 400 psi, these have the highest pressure rating of all our float-operated drain valves.
Keep an eye on condensate collecting in your compressed air line. These drain valves have a clear bowl, so you can see inside to inspect the contents.
Sized right for tight spots.
An external drain provides quick, easy access for cleaning.
With a discharge capacity of more than four gallons per minute, these drain valves can handle large compressed air systems.
When your compressor turns off, it creates back pressure that opens these valves automatically, allowing liquid to escape.
Save energy by minimizing the loss of compressed air. Unlike other drain valves, these only open when they’re full. They close before the reservoir is completely empty, so no air escapes from the system.
Prevent accidental start-up when servicing equipment.
A padlock locks the handle of these valves in the shut-off position so you can disconnect air tools safely.
These valves have a muffler to reduce exhaust noise. A padlock locks the handle in the shut-off position so you can disconnect air tools safely.
Slide the knurled sleeve in one direction to stop flow, and slide it back to start flow again.
Control flow in two directions from a single source—these valves have two balls for independent control and shut-off of each outlet.
Install these valves on your air tank outlet—at the end of the day, they automatically close to save energy.
Also known as blocking valves, these valves allow airflow while an air signal is applied to the air pilot. When the signal stops, the valve closes, trapping air in the system.
Turn airflow on and off with your foot to keep your hands free to perform other tasks.
Also known as solenoid valves, these valves are operated by an electrical signal to turn airflow on or off.
When system pressure reaches the maximum, these valves open and send an air signal to turn on a downstream device such as a discharge valve or throttle. They close and send a signal to turn the device off when pressure drops.
These faucets turn on and off with a quarter turn of the handle.
These faucets drain when closed to prevent freezing.
Turn the handle to start the flow of water; release the handle and the valve shuts off.
Often used in tight spaces, these valves shut off water with a quarter turn of the handle.
Also known as water supply stops, these valves shut off water to faucets, toilets, and fountains.
These valves have a removable key handle to prevent unauthorized use.
For use with low-pressure steam-heating boilers requiring pressure relief at 15 psi, these valves meet ASME Code Section IV.
These valves meet ASME Code Section I for use with steam power boilers requiring pressure relief above 15 psi.
Choose these valves for small steam-heating boilers requiring pressure relief between 5 psi and 12 psi.
Protect your water-heating system with these valves that meet ASME Code Section IV for hot water heaters and boilers.
Control the amount of abrasive material that your blast hose releases by using these valves, which have a knob for adjusting the size of their opening.