McMaster-Carr logo
    Filter by
    For Drill Bit System of Measurement
    Organizer Type
    Number of Taps Stored
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Number of Compartments
    Number of Drill Bits Stored
    Closure Method
    Overall Diameter
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    39 Products

    Tap and Drill Bit Cases

    For Drill Bits
    Image of Product. Front orientation. Tap and Drill Bit Stands. Tap and Drill Bit Cases, For Drill Bits, Steel.
    Image of Product. Front orientation. Tap and Drill Bit Stands. Tap and Drill Bit Cases, For Drill Bits, Plastic.

    Steel

    Plastic

    Store and organize drill bits so they stay in good working condition and don't go missing. These cases have individually marked holes for each size in your set.
    Steel—Steel cases have stands that fold in and out. Stand them up when you need them, then fold them back into the slim case for storage inside a workbench drawer.
    Plastic—Plastic cases have screw-on lids to block out moisture. Compared to steel cases, they're lighter, and they resist rust and dents. Clip them onto your belt to take with you on the job.
    For
    Drill Bit
    Overall
    Material
    No.
    of
    Size
    Dia.
    Lg.
    Wd.
    Ht.
    Features
    Each
    For Inch Drill Bits
     
    For Jobbers' Length
    Steel131/16" to 1/4" (Increments of 1/64")—5 3/8"4"3/8"—000000000000
    Steel151/16" to 1/2" (increments of 1/32")—7"4"1 1/4"—000000000000
    Steel161/64" to 1/4" (increments of 1/64")—5 3/8"4"3/8"—000000000000
    Steel211/16" to 3/8" (Increments of 1/64")—6"4"1 1/8"—000000000000
    Steel291/16" to 1/2" (Increments of 1/64")—7"4"1 3/4"—000000000000
    Plastic291/16" to 1/2" (Increments of 1/64")3"——6 5/8"Belt Clip000000000000
     
    For Maintenance Length
    Plastic291/16" to 1/2" (Increments of 1/64")3 3/4"——6 1/2"Belt Clip000000000000
     
    For Short Length
    Steel291/16" to 1/2" (Increments of 1/64")—7"4"1 3/4"—000000000000
     
    For Extended Length—8" Maximum Drill Bit Length
    Steel291/16" to 1/2" (Increments of 1/64")—8 3/4"4"1 3/4"—000000000000
     
    For Reduced-Shank Length—1/2" Drill Bit Shank Size
    Steel89/16" to 1" (increments of 1/16")—8 1/2"6 1/4"2"—000000000000
     
    For Wire Gauge Drill Bits
     
    For Jobbers' Length
    Steel2080 Ga. to 61 Ga.—2"1 1/2"1/4"—00000000000
    Steel6060 Ga. to 1 Ga.—4 1/2"3 1/4"1"—000000000000
     
    For Short Length
    Steel6060 Ga. to 1 Ga.—4 1/2"3 1/4"1"—000000000000
     
    For Letter Size Drill Bits
     
    For Jobbers' Length
    Steel26A to Z—7"4"1 3/4"—000000000000
     
    For Short Length
    Steel26A to Z—7"4"1 3/4"—000000000000
     
    For Metric Drill Bits
     
    For Jobbers' Length
    Steel131.0 mm to 7.0 mm (Increments of 0.5 mm)—5 1/2"4"1/2"—000000000000
    Steel191.0 mm to 10.0 mm (Increments of 0.5 mm)—6"4"1 1/8"—000000000000
    Steel251.0 mm to 13.0 mm (Increments of 0.5 mm)—7"4"1 3/4"—000000000000
    Steel416.0 mm to 10.0 mm (Increments of 0.1 mm)—7 1/8"4 1/2"2 1/2"—000000000000
    Steel501.0 mm to 5.9 mm (Increments of 0.1 mm)—4 1/2"3 1/4"1"—000000000000
     
    For Inch, Wire Gauge, Letter Size Drill Bits
     
    For Jobbers' Length
    Steel191/16", 1/2", 1/4", 1/8", 21 Ga., 25 Ga., 37/64", 29 Ga., 3/16", 3/32", 3/8", 5/16", 5/32", 5/64", 7 Ga., 7/16", 7/32", F, U—7"4"1 1/4"—000000000000
    Steel1151/16" to 1/2" (Increments of 1/64"), 60 Ga. to 1 Ga., A to Z—13 1/2"4 5/8"2 1/4"—000000000000
    Steel1351/16" to 1/2" (Increments of 1/64"), 80 Ga. to 1 Ga., A to Z—13 1/2"4 5/8"2 1/4"—000000000000
     
    For Short Length
    Steel1151/16" to 1/2" (Increments of 1/64"), 60 Ga. to 1 Ga., A to Z—4 5/8"13 1/2"2 1/4"—000000000000
     
    For Inch, Wire Gauge, Metric Drill Bits
     
    For Jobbers' Length
    Steel1341.0 mm to 13.0 mm (Increments of 0.5 mm), 1/16" to 1/2" (Increments of 1/64"), 80 Ga. to 1 Ga.—13 1/2"4 5/8"2 1/4"—000000000000
     
    For Taps
    Image of Product. Front orientation. Tap and Drill Bit Stands. Tap and Drill Bit Cases, For Taps.
    These cases close for easy transport and are labeled with sizes for organizing tools. Taps are not included.
    Steel—Steel cases have stands that fold in and out. Stand them up when you need them, then fold them back into the slim case for storage inside a workbench drawer.
    Material
    No. of Taps
    Stored
    Holds Tap Sizes
    Lg.
    Wd.
    Ht.
    Each
    Steel21Three each of Nos. 6, 10
    Three each of 1/4", 5/16", 3/8", 7/16", 1/2"    		6 3/16"4 3/8"1 3/8"0000000000000
     
    For Taps and Drill Bits
    Image of Product. Front orientation. Tap and Drill Bit Stands. Tap and Drill Bit Cases, For Taps and Drill Bits.
    These cases close for easy transport and are labeled with sizes for organizing tools. Taps and drill bits are not included.
    Steel—Steel cases have stands that fold in and out. Stand them up when you need them, then fold them back into the slim case for storage inside a workbench drawer.
    Material
    No. of Taps
    Stored
    Holds Tap Sizes
    No. of Drill
    Bits Stored
    Holds Drill Bit Sizes
    Lg.
    Wd.
    Ht.
    Each
    Steel9One each of Nos. 6-32, 8-32, 10-24, 10-32
    One each of 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13    		9One each of Nos. 36, 29, 25, 21, 7
    One each of 5/16", 27/64"
    One each of F, U    		7"4"1 1/4"0000000000000
    Steel9One each of Nos. 6-40, 8-36, 10-24, 10-32
    One each of 1/4"-28, 5/16"-24, 3/8"-24, 7/16"-20, 1/2"-20    		9One each of Nos. 33, 29, 25, 21, 3
    One each of 25/64", 29/64"
    One each of I, Q    		7"4"1 1/4"000000000000
    Steel9One each of M2.5 × 0.45, M3 × 0.5, M3.5 × 0.6, M4 × 0.7, M5 × 0.8, M6 × 1, M8 × 1.25, M10 × 1.5, M12 × 1.759One each of 2.05, 2.5, 2.9, 3.3, 4.2, 5, 6.7, 8.5, 10.2 mm7"4"1 1/4"000000000000
     

    Reduced-Shank Drill Bit Stands

    Each hole is sized to hold the 1/2" shank of a reduced-shank drill bit and marked with a bit size.
    For Drill Bits
    Image of Product. Front orientation. Tap and Drill Bit Stands. Reduced-Shank Drill Bit Stands.
    For
    Drill Bit
    Overall
    Material
    No.
    of
    Size
    Lg.
    Wd.
    Ht.
    Each
    For Inch Drill Bits
     
    1/2" Drill Bit Shank Size
    Steel331/2" to 1" (Increments of 1/64")13"5"2 3/4"0000000000000
     

    Tap and Drill Bit Stands

    For Drill Bits
    Image of Product. Front orientation. Tap and Drill Bit Stands. For Drill Bits.
    These stands hold one of each bit size. Each hole is marked with the size.
    For
    Drill Bit
    Overall
    Material
    No.
    of
    Size
    Lg.
    Wd.
    Ht.
    Each
    For Inch Drill Bits
     
    For Jobbers' Length, Short Length, Extended Length
    Steel291/16" to 1/2" (Increments of 1/64")5 5/8"2 5/8"1 1/2"0000000000000
    Steel331/2" to 1" (Increments of 1/64")13"5"2 3/4"000000000000
     
    For Letter Size Drill Bits
     
    For Jobbers' Length, Short Length, Extended Length
    Steel26A to Z5 5/8"2 5/8"1 1/2"000000000000
     
    For Taps and Drill Bits
    Image of Product. Front orientation. Tap and Drill Bit Stands. For Taps and Drill Bits.
    Keep taps and drill bits organized. All holes are labeled with sizes. Taps and drill bits are not included.
    Material
    No. of Taps
    Stored
    Holds Tap Sizes
    No. of Drill
    Bits Stored
    Holds Drill Bit Sizes
    Lg.
    Wd.
    Ht.
    Each
    Plastic16One each of M2, M3
    Two each of M4, M5, M6, M8, M10, M12, M14    		25Two each of 3.3 mm, 4.5 mm, 12 mm
    One each of 1.8 mm, 2.4 mm, 2.5 mm, 3.4 mm, 4.2 mm, 5 mm, 5.25 mm, 5.5 mm, 6.6 mm, 6.8 mm
    7 mm, 8.5 mm, 8.8 mm, 9 mm, 10.2 mm, 10.8 mm, 12.5 mm, 14 mm, 16 mm    		7"4 1/2"1 11/16"0000000000000
    Plastic26Two each of Nos. 2, 3, 4, 5, 6, 8, 10, 12
    Two each of 1/4", 5/16", 3/8", 7/16", 1/2"    		39Two each of 50 ga., 33 ga., 29 ga.
    One each of 47 ga., 45 ga., 44 ga., 43 ga., 42 ga., 39 ga.
    38 ga., 37 ga., 36 ga., 30 ga., 28 ga., 25 ga., 21 ga., 19 ga., 16 ga., 14 ga., 11 ga., 7 ga., 3 ga.
    One each of F, I, Q, U
    Two of 5/16"
    One each of 7/32", 1/4", 3/8", 25/64", 27/64", 7/16", 29/64", 1/2"    		7 3/8"4 11/16"1 11/16"000000000000
     

    Drill Bit Pouches

    Image of Product. Front orientation. Contains Inset. Drill Bit Pouches. For 7 Drill Bits.
    Image of Product. Front orientation. Contains Inset. Drill Bit Pouches. For 15 Drill Bits.

    For 7 Drill Bits

    For 15 Drill Bits

    Attach these pouches to your belt to easily access drill bits while working.
    For
    Drill Bit
    Pocket
    No.
    of
    Size
    Lg.
    Class
    Wd.
    Ht.
    Wd.
    Ht.
    No. of
    Compartments
    Material
    Closure
    Method
    Color
    Includes
    Each
    For Inch Drill Bits
    71/16" to 1/4"Jobbers
    		3 1/4"4 3/4"1/2" to 3/4"2 1/4" to 2 3/4"7CanvasHook and LoopBlackPlastic Clip000000000000
    71/8" to 1/2"Jobbers
    		3 3/4"6 1/2"3/4" to 1"2 1/2" to 2 3/4"7CanvasHook and LoopBlackPlastic Clip00000000000
    151/16" to 1/2"Jobbers
    		5 1/4"7 1/4"1/2" to 1 1/2"1 3/4" to 5 1/2"15CanvasHook and LoopBlackPlastic Clip00000000000
     

    Magnetic Pouches for Drills

    Image of ProductInUse. Front orientation. Drill Bit Pouches. Magnetic Pouches for Drills.
    Image of Product. Front orientation. Drill Bit Pouches. Magnetic Pouches for Drills.
    This pouch fits onto most hand-held power drills and impact drivers. It has a magnetic panel on the front that can hold bits and fasteners for easy access.
    Pocket
    Wd.
    Ht.
    Wd.
    Ht.
    No. of
    Compartments
    Material
    Closure
    Method
    Color
    Includes
    Each
    For Inch, Metric, Letter Size, Wire Gauge Drill Bits
    4"3"3 3/4" to 4"3 1/4" to 3 1/2"1Nylon FabricZipperBlackAdhesive-Back Hook and Loop0000000000000
     
    back to top