A lithium ion (Li-Ion) battery powers these cordless drills, which means they weigh less and have a longer run-time than cordless drills that use nickel cadmium (NiCad) batteries. All have a variable speed motor—the further you depress the trigger, the faster the drill rotates.

See Batteries and Chargers for Milwaukee Cordless Tools for replacement batteries and chargers.

Straight flutes withstand the heavy pressure needed to penetrate hardened steel. These bits cut more aggressively and resist stress better than spiral-flute bits. A lower-priced alternative to solid carbide, they stay sharp when drilling abrasive material but won’t last as long.

Tough and wear resistant, cobalt steel bits last at least twice as long as high-speed steel. They can also run up to 25% faster at higher temperatures without being damaged on hard materials, such as nickel.

Performance similar to solid carbide but at a lower price point. Like carbide bits, these are stronger than cobalt and high-speed steel and maintain their sharp edges when drilling abrasive material. However, when drilling tough metals like iron and hardened steel, upgrade to carbide for longer life.

Bits have a different tip at each end and snap into the shaft. A ball detent holds the bit in place. To use as nutdriver, remove the bit and turn fasteners with the shaft, which is also reversible.

Four flutes with a 35° helix angle provide a smooth finish on nickel alloys, such as Monel, Inconel, and Hastelloy. Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life on hard materials. They have a square end for milling square-bottomed slots, pockets, and edges. All are center cutting, allowing plunge cuts into a surface.

Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. Their extreme hardness means they are brittle, so a highly rigid setup, such as a CNC machine, is necessary to prevent the end mill from breaking.

A titanium aluminum nitride (TiAlN) coating allows them to dissipate heat better than other end mills, especially at high speeds. At high temperatures, the coating creates a layer of aluminum oxide that transfers heat to the chips, keeping the tool cool, even when used without lubrication. This makes these good for aggressive machining while roughing or making interrupted cuts.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life on hard materials. Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. Their extreme hardness means they are brittle, so a highly rigid setup, such as a CNC machine, is necessary to prevent the end mill from breaking. They have a square end for milling square-bottomed slots, pockets, and edges.

End mills with fewer flutes provide better chip clearance for high-volume, high-speed plunge, slotting, and roughing cuts; end mills with more flutes provide a finer finish and operate with less vibration when run at high speeds.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life on hard materials. Often used for slotting and pocketing cuts in mold and die making, these end mills have a 90° profile and rounded corners, which reduce flute breakage and chipping. Also known as corner radius end mills.

Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. Their extreme hardness means they are brittle, so a highly rigid setup, such as a CNC machine, is necessary to prevent the end mill from breaking.

A titanium aluminum nitride (TiAlN) or aluminum titanium nitride (AlTiN) coating allows them to dissipate heat better than other end mills, especially at high speeds. At high temperatures, the coating creates a layer of aluminum oxide that transfers heat to the chips, keeping the tool cool, even when used without lubrication. This makes these good for aggressive machining while roughing or making interrupted cuts.

End mills with fewer flutes provide better chip clearance for high-volume, high-speed plunge, slotting, and roughing cuts; end mills with more flutes provide a finer finish and operate with less vibration when run at high speeds.