1.2mm Shank Size Drill Bits

Black Oxide—The dark finish increases wear resistance and reduces friction to improve chip flow, so these bits can last 50% longer than uncoated bits.

Gold Oxide—Like black oxide, this finish adds wear resistance and reduces friction for improved chip flow. Because it’s less prone to flaking off, it offers better rust protection when bits aren't in use.

Uncoated—The most economical option, uncoated bits perform best when used on low-carbon steel and aluminum. Polished to reduce friction, they're also known as bright finish bits.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type		Each
Jobbers' Length







				Black Oxide

				1.15	0.0453"	36	11.7	Round	1.2 mm	Standard	0000000	00000


				1.2	0.0472"	38	13.6	Round	1.2 mm	Standard	0000000	0000




						Gold Oxide

						1.15	0.0453"	44	15.8	Round	1.2 mm	Standard	000000000	0000


						1.2	0.0472"	48	19	Round	1.2 mm	Standard	000000000	0000




								Uncoated

								1.15	0.0453"	44	19.1	Round	1.2 mm	Standard	00000000	0000


								1.2	0.0472"	48	25.4	Round	1.2 mm	Standard	00000000	0000


								Short Length







												Black Oxide

												1.2	0.0472"	30	3	Round	1.2 mm	Standard	00000000	0000

Cobalt Steel Drill Bits

Jobbers' Length

Round Shank

Standard

Split

Tough and wear resistant, cobalt steel bits last at least twice as long as high-speed steel. They can also run up to 25% faster at higher temperatures without being damaged on hard materials, such as nickel.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Titanium Nitride (TiN) Coated—Drill at higher speeds and last longer than uncoated and oxide-coated bits, especially on tough materials like hardened steel and nickel.

Titanium Aluminum Nitride (TiAlN) Coated—The hardest and most wear-resistant coating, especially at high temperatures. These bits are best for hard and abrasive materials, such as iron, titanium, and fiberglass.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type		Each
Jobbers' Length







				Titanium Nitride (TiN) Coated

				1.2	0.0472"	38	16	Round	1.2 mm	Standard	0000000	00000




						Titanium Aluminum Nitride (TiAlN) Coated

						1.2	0.0472"	38	16	Round	1.2 mm	Split	00000000	00000




								Gold Oxide

								1.15	0.0453"	36	11.7	Round	1.2 mm	Split	00000000	0000


								1.2	0.0472"	38	13.6	Round	1.2 mm	Split	00000000	0000

Carbide Drill Bits

Jobbers' Length

Round Shank

The hardest and most wear-resistant drill bits you can buy. Carbide bits stay sharp at high temperatures and faster speeds for the best performance on hard and difficult-to-machine materials. They last 10 to 20 times longer than their closest alternative, cobalt steel. Carbide can be brittle, however, so these bits require a rigid machine tool holder to prevent breakage and should not be used in hand drilling applications.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Uncoated—Excellent for a range of materials but won't last as long as coated bits.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type		Each
Jobbers' Length







				Uncoated

				1.2	0.0472"	38	16	Round	1.2 mm	Four Facet	0000000	000000

Left-Hand High-Speed Steel Drill Bits


Jobbers' Length Round Shank	Standard

With flutes that spiral in the opposite direction of other bits, these are primarily used to remove stripped screws. Choose a bit that’s slightly smaller than the diameter of the screw’s head. Set your power tool to rotate in reverse. Slowly drill in the center of the screw head, maintaining constant pressure. As the bit penetrates, it will catch onto the screw and reverse it out of the hole. If the screw is badly stripped, you might need to punch a starter hole. Also known as reverse-flute bits. High-speed steel is the versatile choice for drilling most metals.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Uncoated—The most economical option, uncoated bits perform best when used on low-carbon steel and aluminum. Polished to reduce friction, they're also known as bright finish bits.

					Shank				Each
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type		1-9	10-Up
Jobbers' Length







				Uncoated

				1.2	0.0472"	38	4.8	Round	1.2 mm	Standard	000000000	000000	000000