We will reply to your message within an hour.
Insert these bits directly into power screwdrivers, impact drivers, and other tools that accept 1/4" hex shanks.
The 1/4" hex shank allows these bits to be used with standard impact drivers.
Also known as spade bits, these have a centering point and two cutting edges for boring holes in hard and soft wood.
An open spiral-flute design clears chips quickly, so these bits can bore smooth, deep holes through construction lumber, railroad ties, and utility poles. Also known as pole or ship auger bits.
The screw point draws the bit in, quickly boring holes without applying pressure.
Insert directly into power screwdrivers, impact drivers, and other tools that accept a 1/4" hex shank.
Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules.
Adjust these extensions to the desired length. They have a quick-change mechanism for fast bit changes.
A quick-change mechanism allows fast bit changes.
Strong and durable, these multipurpose bits are for use with bit screwdrivers. They are often used with power tools to install sheet metal screws.
Remove screws in hard-to-reach places. A spring-loaded sleeve guides bits onto the screw head and keeps them from slipping out.
Strong and durable, these multipurpose bits are for use with bit screwdrivers.
The toughest bits available, these withstand the shock and twisting force of impact drivers.
When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.
Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.
A retaining ring at the tip grips inside the recess to ensure screws won't slip off the bit.
When you don't have exact alignment between the fastener and the bit, the ball end allows angled entry to turn screws in hard-to-reach areas. A retaining ring grips inside the recess to hold screws in place.
Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.
Ribs forged into the wings of these bits grip the screw recess to reduce stripping. They're also known as ACR® bits.
An exterior stop collar prevents fasteners from being driven too deep. Use with soft material such as drywall, wood, and fiberboard.
The small-diameter shaft can access screws in narrow recessed holes.
A three-winged tip fits triangular slotted screw recesses.
Strong and durable, these multipurpose bits are often used with power tools to install sheet metal screws.
The slightly tapered tip wedges into the screw recess for a secure hold. Also known as Torx-Align bits.
Strong and durable, these multipurpose bits are for use with bit screwdrivers. They're designed for screws with a square recess in the head and are also known as Robertson bits.
The toughest bits available, these withstand the shock and twisting force of impact drivers. Designed for screws with a square recess in the head, they are also known as Robertson bits.
An exterior stop collar prevents fasteners from being driven too deep. Use with soft materials such as drywall, wood, and fiberboard.
An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.
Use with screws that have two drilled holes.
These bits provide a secure grip on the Phillips/slotted combination-drive screws in electrical equipment.
These bits are shaped like a 12-pointed star. They're also known as XZN bits.
While screws with a Square/Phillips combination drive can be turned with either a Square or Phillips bit, these make the best contact so you can apply high torque without slipping and stripping the recess. They are also known as Quadrex bits.
These bits have an offset cross shape. They’re also known as ACR® bits.
Ribs forged into the wings of these offset-cross-shaped bits grip the screw recess to reduce stripping. They are also known as ACR® bits.
An opening at the tip accommodates the pin in the recess of tamper-resistant hex screws. These are also known as pin-in-hex or pin-in-socket bits.
The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.
An opening at the tip accommodates the pin in the recess of tamper-resistant square screws.
Also known as Reed and Prince bits.
These are also known as known as butterfly and Type G bits.
Grip the indentations on the head of tri-groove fasteners.
A magnet or retaining ring holds the nut in place.
The toughest bits available, these withstand the shock and twisting force of impact drivers. A magnet holds the nut in place.
Because they make contact on the flat sides of fasteners rather than only on the corners, these magnetic bits significantly reduce slipping and stripping. They’re also known as lobular bits.
Turn hex nuts and cap screws.
A slot in these bits holds and turns wing nuts.
Install and remove eyebolts and screw-in hooks.
Use to install wood screw threaded studs (also known as dowel screws).
Quickly install threaded rods and studs using a cordless drill, instead of doing it by hand.
One-way screws can be installed with standard slotted screwdrivers but can only be removed with this type of bit.
Turn the flat-end bolts and screws that are commonly used for wire guiding and hanging pipes and fixtures.
Lock your bit into the adapter to prevent accidental disengagement. These adapters hold hex-shank bits (also known as insert bits) in powered tools.
The head is angled 90° to drive fasteners in tight spaces. Use these adapters to hold hex-shank bits (also known as insert bits) in powered tools.
Use hex-shank bits (also known as insert bits) in powered tools.
Bend these adapters up to 90° to access hard-to-reach fasteners. Use them to hold hex-shank bits (also known as insert bits) in powered tools.
Keep bits from slipping. Insert a bit into the adapter, place a screw on the end of the bit, and slide the adapter sleeve over the screw. The sleeve retracts as the screw is driven. These adapters hold hex-shank bits (also known as insert bits) in powered tools.
A magnetic ring at the end of the adapter holds flat-head screws in place to ensure good contact between the bit and screw. Use these adapters to hold hex-shank bits (also known as insert bits) in powered tools.
These adapters are designed to withstand the high torque of impact drivers. They hold hex-shank bits (also known as insert bits).
Assortments contain bits with multiple drive styles.
A retaining ring grips inside the recess to hold screws in place. These bits have a ball end that allows angled entry to drive screws in hard-to-reach areas.
A magnet holds the nut in place.
These bits are also known as nut setters.
The slightly tapered tip wedges into the screw recess for a secure hold. These are also known as Torx-Align bits.
These bits have an offset cross shape.
Designed for the fasteners used in electronics assembly, the tip of these bits has slightly sharper corners than Phillips style.
Also known as Robertson bits these are designed for screws with a square recess in the head.