McMaster-Carr logo
    Filter by
    System of Measurement
    ID
    Attribute Image
    Shaft Diameter
    Attribute Image
    Shell Material
    Plain Bearing Type
    Backing Material
    Drill Bushing Texture
    Hardness
    Installation Permanence
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Width
    Attribute Image
    Lubrication
    Reamer Diameter
    Drill Bushing Type
    Shaft Mount Type
    Bearing Material
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    4 Products

    Press-Fit Reamer Bushings

    Image of ProductInUse. Front orientation. Drill Bushings. Press-Fit Reamer Bushings.
    Image of Product. Front orientation. Drill Bushings. Press-Fit Reamer Bushings.
    With ID tolerances sized specifically for reamers, these bushings ensure steady and precise hole finishing. Press them into a fixture plate with a manual or hydraulic press for permanent installation. Also known as headless bushings, these ANSI-type P bushings don’t need counterboring to be mounted flush. They are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.
    Tolerance
    ID
    OD
    Lg.
    For Reamer
    Dia.
    ID
    OD
    Lg.
    Drill Bushing
    Type
    Material
    Hardness
    Each
    0.499"3/4"1"0.499"0.0006" to 0.001"0.0015" to 0.0018"-0.01" to 0.01"PSteelRockwell C619473N365000000

    Dry-Running Metal-Reinforced Plastic Sleeve Bearings

    Image of Product. Front orientation. Sleeve Bearings. Dry-Running Metal-Reinforced Plastic Sleeve Bearings.
    Combine slippery plastic with the strength of metal. The PTFE core is naturally slippery, so you’ll never have to add lubricant. These bearings also keep your workspace clean with no lubricant to drip or flake and attract dust. Compared to all-metal bearings, they are lighter.
    With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.
    Bronze-Backed PTFE with Steel Shell—A good all-around, economical choice. Although these bearings are stronger than aluminum, they can only be used in dry environments where corrosion is not a concern.
    For Shaft
    Dia.
    For Housing
    ID
    Lg.
    Dynamic Radial Load
    Cap. @ Speed
    Temp. Range,
    ° F
    Each
    Bronze-Backed PTFE with Steel Shell
    1/2"19/32"5/8"990 lb. @ 120 rpm-320 to 53060695K300000
     

    Dry-Running Mounted Sleeve Bearings

    Image of Product. Front orientation. Contains Annotated. Mounted Bearings. Dry-Running Mounted Sleeve Bearings.
    Leave the lubricant in the supply closet—these low-maintenance bearings are made from naturally slippery plastic. They'll keep shafts spinning with no messy grease to drip off, wash out, or collect dust. With no moving parts, sleeve bearings stand up to grimy environments better than ball bearings. However, with more friction generated, they're less effective at high speeds. The sturdy housing bolts down to support shafts as they turn.
    High-Load Bronze-Backed PTFE—Reinforced with metal, these slick PTFE bearings carry load ratings at least seven times greater than any plastic alternative. The slippery material is a good fit for conveyors and other machinery with frequent starts and stops.
    Aluminum Housing—One-third the weight of cast iron but not as strong. Aluminum also resists corrosion.
    Misalignment Capability—Bearings compensate for as much shaft misalignment as the degree listed. This extends the life of the bearing and protects against wear if shafts are slightly askew.
    Overall
    For Shaft
    Dia.
    Ctr.
    Ht.
    Lg.
    Wd.
    Dynamic Radial Load
    Cap. @ Speed
    Misalignment
    Capability
    Each
    High-Load Bronze-Backed PTFE Bearing with Aluminum Housing
    1/2"3/4"3 1/4"25/32"1,200 lb. @ 120 rpm5°2820T6000000
     

    Dry-Running Mounted Sleeve Bearings with Two-Bolt Flange

    Image of Product. Front orientation. Contains Annotated. Mounted Bearings. Dry-Running Mounted Sleeve Bearings with Two-Bolt Flange.
    Leave the lubricant in the supply closet—these low-maintenance bearings are made from naturally slippery plastic. They'll keep shafts spinning with no messy grease to drip off, wash out, or collect dust. With no moving parts, sleeve bearings stand up to grimy environments better than ball bearings. However, with more friction generated, they're less effective at high speeds. The sturdy housing supports the shaft and secures with a two-bolt flange, the most common type of flanged bearing.
    High-Load Bronze-Backed PTFE—Reinforced with metal, these slick PTFE bearings carry load ratings at least seven times greater than any plastic alternative. The slippery material is a good fit for conveyors and other machinery with frequent starts and stops.
    Aluminum Housing—One-third the weight of cast iron but not as strong. Aluminum also resists corrosion.
    Misalignment Capability—Bearings compensate for as much shaft misalignment as the degree listed. This extends the life of the bearing and protects against wear if shafts are slightly askew.
    Overall
    For Shaft
    Dia.
    Lg.
    Wd.
    Flange
    Thk.
    Dynamic Radial Load
    Cap. @ Speed
    Misalignment
    Capability
    Each
    High-Load Bronze-Backed PTFE Bearing with Aluminum Housing
    1/2"3 1/4"25/32"1/4"1,200 lb. @ 120 rpm5°2820T36000000
     
    back to top