A sealed design prevents contamination in dirty and dusty environments.

A solenoid automatically starts and stops flow to a single lubrication point to dispense lubricant while equipment is running.

Thread these dispensers directly into bearing housings, pumps, and other machinery. Flip the lever to start and stop flow; turn the dial to adjust flow.

Serve multiple lubrication points from a single location.

Control the flow of oil to a single lubrication point.

Use these brushes to lubricate chain, gears, and conveyors. Connect to an oil dispenser, then turn the dial to adjust flow.

Use this dispenser to brush oil on chain, gears, and conveyors. Often used to replenish lubricant after washdowns.

Flip the lever to start and stop flow.

Install these valves in tight spots, such as where pipelines are crowded together. They’re less than half as long as standard threaded valves and one-third shorter in height. Use with water, oil, air, and inert gas.

These valves handle twice the pressure of other compact valves. Install them in tight spots, such as where pipelines are crowded together. Use with water, oil, air, and inert gas.

Use these valves in general purpose applications, such as those with water, oil, air, and inert gas.

An easy-to-read flow-indicating handle shows the percentage the valve is open. These valves are for use with water, oil, inert gas, and steam.

Monitor and maintain flow quality from a single valve—these valves have a gauge port, strainer, and drain built in.

For applications that require intermittent operation, such as spraying and washing, push or pull the lever on these valves to start flow. They spring closed when the lever is released.

Rated for at least three times the pressure of standard threaded valves, these valves are used to start and stop the flow of compressed gas, pressurized water, or steam.

For fast installation and removal from pipelines, these valves have a union fitting that disassembles into multiple pieces. They’re for use with water, oil, air, inert gas, and steam.

Access the handle of these valves while protecting your line behind an instrument panel. They have threads and a hex nut below the handle for panel mounting.

Fit these short and slim valves in control boxes, panels, and other tight spots. Made of plastic, they won’t pit or corrode on the inside like metal valves, and they’re lighter in weight for easy handling.

Use these valves with water, air, and inert gas.

Also known as pinch valves, these valves stop flow by squeezing tubing from the outside. Since they don’t directly contact your fluid, they’re good for applications where you need to prevent contamination.

Weld these valves to unthreaded metal pipe for a permanent, flush connection that permits smooth flow through a line. Use with water, oil, inert gas, and steam.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Often used for oxygen service and other high-purity applications, these valves come cleaned and bagged. Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. For easy maintenance, they have a three-piece bolted body that disassembles inline so you can access internal components without removing welded connections.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. The socket ends of these valves are lined with PVC for bonding to PVC pipe.

Install these valves in tight spaces—they have a short body length and low profile. A barbed end grips onto tubing for a secure hold.

Use these plastic valves for a lightweight and economical alternative to metal. They have a compression sleeve that bites into tubing as you tighten the nut, forming a strong seal. Use with water, air, and inert gas.

Built to withstand pressures up to 4,500 psi, these valves are ideal for high-pressure lines. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings

Bolt these valves to ANSI flanges.

Crimp these valves to metal tubing for a permanent, leak-tight connection that doesn’t require heat or soldering.

For extra gripping power and a strong seal, the Yor-Lok fittings on these valves have two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

Flip the toggle to quickly turn these valves on and off. All have threads and a hex nut below the handle for installation in instrument panels. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

A short body length and low profile make these valves ideal for installation in tight spaces, such as between pipelines. They have a compression sleeve that bites into tubing as you tighten the nut.

With a three-piece bolted body that disassembles for access to internal components, you can clean and repair these valves without removing them from your line. A compression sleeve bites into tubing as you tighten the nut, forming a strong seal.

Monitor and maintain flow quality from a single valve. Thanks to their solder-connect union fitting, these valves are especially useful in lines that require frequent maintenance and cleaning.

The most chemical-resistant threaded valves we offer, these have a PTFE seal and an alloy body that can withstand extremely aggressive and corrosive chemicals, such as methyl ethyl ketone and toluene.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. All have a fluoroelastomer seal and a plastic body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

Streamline your installation and removal process. These valves give you the leak-tight permanent connection of a socket connect with the ease of fittings that come apart.

Bolt these valves onto ANSI flanges. They meet NSF/ANSI standard 61, so they’re safe for use in drinking water systems.

Connect these valves to tubing with a ring and a crimping tool. They meet the strict standards of NSF/ANSI 61, so they’re safe to use with drinking water.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves meet NSF/ANSI 61, which means they’re safe to use with drinking water systems.

Insert your tubing into the fittings of these valves with just a push—the internal rings will grip it tight. Made of plastic, these valves are a lightweight alternative to metal valves. All meet NSF/ANSI 61 for safe use with drinking water.

Barbs grip onto tubing to give these valves a secure hold. These valves meet NSF/ANSI 61, so they’re safe to use with drinking water.

A short body length and low profile make these valves ideal for installation in tight spaces, such as behind panels. They meet NSF/ANSI 61 standards for safe use in drinking water systems.

Protect your drinking water line behind an instrument panel while keeping the handle handy. These valves have a nut that threads onto the stem to mount the handle onto the panel.

Disassemble the union fittings on these valves for fast installation and removal from your pipeline. All meet NSF/ANSI 61 for use with drinking water.

No need to completely remove these valves from your line for cleaning and repairs. The bolted three-piece body comes apart, so you can easily access their internal components.

The bolted-body design provides strength for a tight seal in vacuum conditions up to 29.9” Hg. Use these valves in vacuum applications, such as coating, heat treating, leak testing, and analyzing gases.

For strong, permanent connections that are quick to install, push PVC pipe into these valves and a rubber ring grips it. Also known as gate valves, they open and close gradually to prevent damage to your system from sudden changes in flow.

Flexible joints keep these valves tightly sealed during pressure changes or vibrations from heavy machinery.

FM-approved, these valves are often used to isolate sections of your facility’s water supply for fire suppression and protection.

Built to handle the extreme cold of liquid gases, these bronze valves are ideal for liquid carbon dioxide carbonation systems, liquid nitrogen coolant systems, and other cryogenic applications.

A rubber-coated gate, also known as a resilient wedge, compresses against the valve seat to give these valves a tight, leakproof seal. Since they bolt onto flanges, they’re easier to install and remove than threaded and weld-on valves.

Also known as gate valves, these valves gradually open and close to prevent system damage from suddenly starting and stopping flow.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection.

With a forged steel body and bolted construction, these valves can withstand nearly 10 times the pressure of other socket-connect gradual valves.

Easier to install and remove for maintenance than threaded and weld-on valves, these valves bolt and unbolt to flanges. They meet NSF/ANSI 61 for safe use in drinking water systems.

For a leak-tight connection in drinking water lines without heat or soldering, crimp the fittings on these valves to metal tubing with a press-connect crimping tool. They open and close gradually with multiple turns of the handle wheel to prevent jolts from sudden stops and starts.

Designed to withstand the high temperatures and pressures in steam service applications.

Turn the knob to adjust how much these valves will open or close when actuated. They are often used in irrigation and landscaping applications.

Lower profile and available in smaller connection sizes than standard valves, these fit in tight spots.

Less than half the size of our other compact valves, these have small pipe connections for miniature lines.

Designed for controlling single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

Control flow in high-pressure lines in tight spots—these valves have the highest pressure ratings of our compact valves.

To fit in tight spots, these valves have a slimmer body than standard valves with an exhaust port.

These valves have threaded NPT connections.

Separate the union fittings on each end of these valves for fast installation and removal from pipelines.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

Also known as butterfly valves.

A compact, lightweight actuator and an angular body allow you to install these valves in any mounting orientation.

Limit wear and damage in high-cycling applications—these valves have additional seals that prevent leakage to reduce maintenance time.

Less than half the height of standard severe-duty valves, these fit in small spaces and low-clearance pipelines.

The three-piece bolted body comes apart for access to internal components without unthreading pipe connections and removing the valve from your line.

With a shorter end-to-end length than other check valves, these fit in tight spaces.

With few moving parts to wear out, these valves withstand frequent opening and closing, pulsating flow, and rapid flow reversal.

To achieve the maximum possible flow, internal components are designed to reduce flow resistance.

Plastic provides a lightweight alternative to metal.

Solder these valves to copper tubing for a permanent, leak-tight connection.

With internal components that resist wear from frequent operation, these valves can cycle as often as once per second.

Two sleeves give the fittings extra gripping power. They bite into tubing as you tighten the nut to form a strong seal. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

For more durability than plastic barbed check valves, these have a stainless steel body.

Visually inspect flow and debris accumulation through the transparent valve body.

Sandwich these valves between two ANSI flanges for backflow prevention at a fraction of the weight of flanged check valves and a reduced pipeline footprint.

Less than half the end-to-end length of standard flange-mount check valves, these can be installed in pipelines with limited clearance.

Body is plastic.

For more durability than plastic, these valves have a metal body.

Sandwich these valves between ANSI flanges.

The most chemical-resistant check valves in our offering, these have a PFA body to withstand methyl ethyl ketone, sodium hypochlorite, and other extremely harsh chemicals.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Use with water. Valves divert flow between ports.

Also known as shuttle valves, these automatically switch the inlet source as pressure changes; they always direct flow from the higher-pressure side-port inlet to the top-port outlet. Use them with water, oil, air, and inert gas.

Divert the flow of compressed air and other media to multiple pieces of equipment. Use with water, oil, air, and inert gas.

A metal body provides more strength and durability than plastic. These valves have a low-profile handle and a short end-to-end length to fit in tight spots. All are for use with water, oil, air, and inert gas. They divert flow between ports.

Barbs grip onto tubing, providing a secure hold. Use with water, oil, air, and inert gas. These valves divert flow between ports in tubing lines.

Bolt these valves to flanges to divert flow between ports in flanged pipelines. They’re for use with water, oil, air, and inert gas.

These valves operate on electricity to automatically divert flow between ports. Use with water, oil, air, and inert gas.

Lower profile than other solenoid diverting valves and available in smaller pipe sizes, these valves are often used to automatically divert flow between ports in tight spots. Use them with water, oil, air, and inert gas. All operate on electricity.

Bolt these valves to flanges. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

Empty fluid from tanks in boiler rooms or heat transfer systems—these valves withstand higher temperatures than our other drain valves. Also known as stop cocks.