McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    145 Products

    Door Kick Plates

    Image of ProductInUse. Front orientation. Door Kick Plates.
    Kick plates prolong the life of doors by shielding them from scratches, dings, and marks in high-traffic areas. They also keep moisture from damaging the base of doors in facilities that require frequent mopping and cleaning. Our kick plates are tested with salt spray to meet ANSI A156.6 requirements for strength, appearance, and durability. They stay looking like new, even when installed outdoors in humid or wet environments.
    Screw In
    Image of Product. Front orientation. Door Kick Plates. Screw In.
    Mount with the included self-drilling screws and skip drilling a hole. The screws match the finish of the plates and sit flush to create a clean, smooth look.
    Brass—With a shiny, warm finish, these kick plates give doors an elegant appeal. They resist corrosion about as well as 304 stainless steel but require occasional polishing to clean up smudges and avoid tarnish.
    Width—Select a kick plate 2" narrower than your door to prevent obstructions when opening and closing it.
    Height—Kick plates 34" to 46" in height guard against damage from carts or dollies better than shorter plates.
    Ht.
    Thk.
    For Use
    Outdoors
    Mounting Fasteners
    Included
    Polished
    Brass
    24" Wide
    34"0.05"YesYes1401A510000000
     
    28" Wide
    6"0.05"YesYes1401A52000000
    8"0.05"YesYes1401A53000000
    10"0.05"YesYes1401A54000000
    12"0.05"YesYes1401A55000000
    36"0.05"YesYes1401A56000000
    42"0.05"YesYes1401A57000000
     
    30" Wide
    6"0.05"YesYes1401A58000000
    8"0.05"YesYes1401A59000000
    10"0.05"YesYes1401A61000000
    12"0.05"YesYes1401A62000000
     
    34" Wide
    6"0.05"YesYes1401A63000000
    8"0.05"YesYes1401A64000000
    10"0.05"YesYes1401A65000000
    12"0.05"YesYes1401A66000000
    16"0.05"YesYes1401A67000000
    34"0.05"YesYes1401A68000000
    36"0.05"YesYes1401A69000000
    46"0.05"YesYes1401A71000000
     
    36" Wide
    8"0.05"YesYes1401A72000000
    10"0.05"YesYes1401A73000000
    12"0.05"YesYes1401A74000000
     
    48" Wide
    8"0.05"YesYes1401A75000000
    12"0.05"YesYes1401A76000000
    16"0.05"YesYes1401A77000000
     

    Fabric Grommet Kits

    Kits include grommets of a single size and all the tools you need to install them. The grommets add a protective metal ring to a hole so rope and cable don’t tear your tarp, cover, or curtain. Strike the cutting punch with a mallet to create a hole, then set the grommet using the installation punch and die set.
    Standard Washer
    Image of Product. Front orientation. Contains Annotated. Grommets. Fabric Grommet Kits, Standard Washer.
    Image of Product. Front orientation. Grommets. Fabric Grommet Kits.
    Brass—Add a bright finish to your fabric.
    Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.
    Grommet
    Trade Size
    For Max.
    Material Thk.
    ID
    Flange
    Dia.
    Dp. Under
    Flange
    For Use
    Outdoors
    Mil. Spec.
    Includes
    No. of
    Grommets
    Each
    Brass
    00.1"1/4"0.545"0.175"YesMIL-G-16491Cutting Block, Cutting Punch, Die Set, Installation Punch249610K31000000
    10.1"9/32"0.687"0.185"YesMIL-G-16491Cutting Block, Cutting Punch, Die Set, Installation Punch249610K3200000
    20.14"3/8"0.815"0.215"YesMIL-G-16491Cutting Block, Cutting Punch, Die Set, Installation Punch249610K1300000
    30.21"7/16"0.97"0.295"YesMIL-G-16491Cutting Block, Cutting Punch, Die Set, Installation Punch129610K3400000
    40.29"1/2"1.05"0.374"YesMIL-G-16491Cutting Block, Cutting Punch, Die Set, Installation Punch129610K3500000
     
    Tooth-Lock Washer
    Image of Product. Front orientation. Contains Annotated. Grommets. Fabric Grommet Kits, Tooth-Lock Washer.
    Image of Product. Front orientation. Grommets. Fabric Grommet Kits.
    Teeth grip the fabric for a stronger hold than standard washers.
    Brass—Add a bright finish to your fabric.
    Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.
    Grommet
    Trade Size
    For Max.
    Material Thk.
    ID
    Flange
    Dia.
    Dp. Under
    Flange
    For Use
    Outdoors
    Mil. Spec.
    Includes
    No. of
    Grommets
    Each
    Brass
    00.11"1/4"0.545"0.175"YesMIL-G-16491Cutting Block, Cutting Punch, Die Set, Installation Punch489610K16000000
    10.12"9/32"0.687"0.185"YesMIL-G-16491Cutting Block, Cutting Punch, Die Set, Installation Punch489610K1700000
    20.15"3/8"0.815"0.215"YesMIL-G-16491Cutting Block, Cutting Punch, Die Set, Installation Punch249610K1800000
    30.23"7/16"0.97"0.295"YesMIL-G-16491Cutting Block, Cutting Punch, Die Set, Installation Punch249610K1900000
    40.3"1/2"1.05"0.374"YesMIL-G-16491Cutting Block, Cutting Punch, Die Set, Installation Punch249610K2100000
     

    Fabric Grommets

    Add a protective metal ring to a hole so rope and cable don’t tear your tarp, cover, or curtain. To install, strike a cutting punch with a mallet to create the hole, then set the grommet using either an installation punch or a press. All of these grommets can be used outdoors. Installation tools are sold separately.
    Standard Washer
    Image of Product. Front orientation. Contains Annotated. Grommets. Fabric Grommets, Standard Washer.
    Brass—Add a bright finish to your fabric.
    Nickel-Plated Brass—The nickel gives these a more muted, silvery look than our other brass grommets.
    Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.
    Grommet
    Trade Size
    For Max.
    Material Thk.
    ID
    Flange
    Dia.
    Dp. Under
    Flange
    For Use
    Outdoors
    Mil.
    Spec.
    Pkg.
    Qty.
    Pkg.
    Brass
    000.063"3/16"0.425"0.135"YesNASM20230509604K2100000
    00.101"1/4"0.545"0.175"YesNASM20230509604K220000
    10.108"9/32"0.687"0.185"YesNASM20230509604K230000
    20.14"3/8"0.815"0.215"YesNASM20230509604K2400000
    30.219"7/16"0.97"0.295"YesNASM20230509604K2500000
    40.298"1/2"1.05"0.374"YesNASM20230509604K2600000
    50.254"5/8"1.22"0.33"YesNASM20230259604K2700000
    60.149"13/16"1.75"0.232"YesNASM20230109604K2800000
     
    Nickel-Plated Brass
    000.063"3/16"0.425"0.135"YesNASM164915086625K310000
    00.101"1/4"0.545"0.175"YesNASM164915086625K3200000
    10.108"9/32"0.687"0.185"YesNASM164915086625K3300000
    20.14"3/8"0.815"0.215"YesNASM164915086625K3400000
    30.219"7/16"0.97"0.295"YesNASM164915086625K3500000
    40.298"1/2"1.05"0.374"YesNASM164912586625K3600000
    50.254"5/8"1.22"0.33"YesNASM164912586625K3700000
    60.149"13/16"1.75"0.232"YesNASM164911086625K3800000
     
    Accessories for Grommets
    Installation and Cutting Punches
    Image of Product. Front orientation. Fabric Fastener Installation Tools. Hammer-Driven Installation Punch.

    Hammer-Driven

    Installation

    Punch

    Image of Product. Front orientation. Fabric Fastener Installation Tools. Hammer-Driven Cutting Punch.

    Hammer-Driven

    Cutting Punch

    Hammer-Driven Installation Punch—The economical choice if you’re installing a few grommets at a time. Align the grommet base, fabric, and washer on the die (included). A few sharp taps on the punch cinch the grommet in the hole. Use a rubber or rawhide mallet rather than a metal hammer to preserve the head of the punch.
    Hammer-Driven Cutting Punch—Create a hole in your fabric with a few sharp mallet taps on the cutting punch. Use a rubber or rawhide mallet rather than a metal hammer to preserve the head of the punch.
    For Grommet
    Trade Size
    For Hole
    Dia.
    Material
    Each
    Hammer-Driven Installation Punch
    003/16"—9612K25000000
    01/4"—9612K2600000
    19/32"—9612K2700000
    23/8"—9612K2800000
    37/16"—9612K2900000
    41/2"—9612K3100000
    55/8"—9612K3200000
    613/16"—9612K3300000
     
    Hammer-Driven Cutting Punch
    003/16"Steel9611K1100000
    01/4"Steel9611K1200000
    19/32"Steel9611K1300000
    23/8"Steel9611K1400000
    37/16"Steel9611K1500000
    41/2"Steel9611K1600000
    55/8"Steel9611K1700000
    63/4"Steel9611K1800000
     
    Manual Presses
    Image of Product. Front orientation. Contains Annotated. Fabric Fastener Installation Tools. Manual Press.

    Manual Press

    Manual Press—Saves time and effort if you’re frequently installing or replacing grommets. Install the required two-piece die set (sold separately) on the press, align the grommet in the hole, and squeeze the handle. For a longer service life, lubricate the handle and plunger with a drop of oil.
    Throat
    Max.
    Opening
    Dp.
    Wd.
    Material
    Each
    Manual Press
    7/8"3 1/4"1 3/4"Aluminum
    		95720A6900000000
     
    Grommet Dies
    Image of Product. Front orientation. Grommet Dies.
    For Grommet
    Trade Size
    Hole
    Size
    Each
    003/16"95720A710000000
    01/4"95720A71500000
    19/32"95720A72000000
    23/8"95720A73000000
    37/16"95720A74000000
    Tooth-Lock Washer
    Image of Product. Front orientation. Contains Annotated. Grommets. Fabric Grommets, Tooth-Lock Washer.
    Teeth grip the fabric for a stronger hold than standard washers.
    Brass—Add a bright finish to your fabric.
    Nickel-Plated Brass—The nickel gives these a more muted, silvery look than our other brass grommets.
    Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.
    Grommet
    Trade Size
    For Max.
    Material Thk.
    ID
    Flange
    Dia.
    Dp. Under
    Flange
    For Use
    Outdoors
    Mil.
    Spec.
    Pkg.
    Qty.
    Pkg.
    Brass
    00.101"1/4"0.545"0.175"YesNASM16491509605K2100000
    10.108"9/32"0.687"0.185"YesNASM16491509605K220000
    20.141"3/8"0.815"0.215"YesNASM16491509605K2300000
    30.219"7/16"0.97"0.295"YesNASM16491509605K2400000
    40.295"1/2"1.05"0.374"YesNASM16491509605K2500000
    50.251"5/8"1.22"0.33"YesNASM16491259605K2600000
     
    Nickel-Plated Brass
    00.101"1/4"0.545"0.175"YesNASM16491509604K310000
    10.108"9/32"0.687"0.185"YesNASM16491509604K3200000
    20.141"3/8"0.815"0.215"YesNASM16491509604K3300000
    30.219"7/16"0.97"0.295"YesNASM16491259604K340000
     
    Accessories for Grommets
    Installation and Cutting Punches
    Image of Product. Front orientation. Fabric Fastener Installation Tools. Hammer-Driven Installation Punch.

    Hammer-Driven

    Installation

    Punch

    Image of Product. Front orientation. Fabric Fastener Installation Tools. Hammer-Driven Cutting Punch.

    Hammer-Driven

    Cutting Punch

    Hammer-Driven Installation Punch—The economical choice if you’re installing a few grommets at a time. Align the grommet base, fabric, and washer on the die (included). A few sharp taps on the punch cinch the grommet in the hole. Use a rubber or rawhide mallet rather than a metal hammer to preserve the head of the punch.
    Hammer-Driven Cutting Punch—Create a hole in your fabric with a few sharp mallet taps on the cutting punch. Use a rubber or rawhide mallet rather than a metal hammer to preserve the head of the punch.
    For Grommet
    Trade Size
    For Hole
    Dia.
    Material
    Each
    Hammer-Driven Installation Punch
    01/4"—9612K26000000
    19/32"—9612K2700000
    23/8"—9612K2800000
    37/16"—9612K2900000
    41/2"—9612K3100000
    55/8"—9612K3200000
     
    Hammer-Driven Cutting Punch
    01/4"Steel9611K1200000
    19/32"Steel9611K1300000
    23/8"Steel9611K1400000
    37/16"Steel9611K1500000
    41/2"Steel9611K1600000
    55/8"Steel9611K1700000
     
    Manual Presses
    Image of Product. Front orientation. Contains Annotated. Fabric Fastener Installation Tools. Manual Press.

    Manual Press

    Manual Press—Saves time and effort if you’re frequently installing or replacing grommets. Install the required two-piece die set (sold separately) on the press, align the grommet in the hole, and squeeze the handle. For a longer service life, lubricate the handle and plunger with a drop of oil.
    Throat
    Max.
    Opening
    Dp.
    Wd.
    Material
    Each
    Manual Press
    7/8"3 1/4"1 3/4"Aluminum
    		95720A6900000000
     

    Reinforcing Fabric Grommets

    These grommets handle thick materials and strain from fabric that’s frequently pulled or stretched. Strike a cutting punch with a mallet to create the hole, then set the grommet using either an installation punch or a press. Installation tools are sold separately.
    Extended-Neck Washer
    Image of Product. Front orientation. Contains Annotated. Grommets. Reinforcing Fabric Grommets, Extended-Neck Washer.
    An extended neck gives these washers a stronger hold than our other fabric grommets.
    Brass—Add a bright finish to your fabric.
    Nickel-Plated Brass—The nickel gives these a more muted, silvery look than our other brass grommets.
    Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.
    Grommet
    Trade Size
    For Max.
    Material Thk.
    ID
    Flange
    Dia.
    Dp. Under
    Flange
    For Use
    Outdoors
    Mil. Spec.
    Pkg.
    Qty.
    Pkg.
    Brass
    000.062"3/16"0.425"0.135"YesAN230, MIL-G-16491, NASM16491, NASM20230508271K3100000
    00.102"1/4"0.545"0.175"YesAN230, MIL-G-16491, NASM16491, NASM20230508271K3200000
    10.112"9/32"0.687"0.185"YesAN230, MIL-G-16491, NASM16491, NASM20230508271K3300000
    20.139"3/8"0.815"0.215"YesAN230, MIL-G-16491, NASM16491, NASM20230508271K3400000
    30.218"7/16"0.97"0.295"YesAN230, MIL-G-16491, NASM16491, NASM20230508271K3500000
    40.296"1/2"1.05"0.374"YesAN230, MIL-G-16491, NASM16491, NASM20230258271K3600000
     
    Nickel-Plated Brass
    000.062"3/16"0.425"0.135"YesAN230, MIL-G-16491, NASM20230509604K350000
    00.102"1/4"0.545"0.175"YesAN230, MIL-G-16491, NASM20230509604K360000
    10.112"9/32"0.687"0.185"YesAN230, MIL-G-16491, NASM20230509604K3700000
    20.139"3/8"0.815"0.215"YesAN230, MIL-G-16491, NASM20230509604K3800000
    30.218"7/16"0.97"0.295"YesAN230, MIL-G-16491, NASM20230259604K3900000
     
    Accessories for Grommets
    Installation and Cutting Punches
    Image of Product. Front orientation. Fabric Fastener Installation Tools. Reinforcing, Hammer-Driven Installation Punch.

    Hammer-Driven

    Installation

    Punch

    Image of Product. Front orientation. Fabric Fastener Installation Tools. Reinforcing, Hammer-Driven Cutting Punch.

    Hammer-Driven

    Cutting Punch

    Hammer-Driven Installation Punch—The economical choice if you’re installing a few grommets at a time. Align the grommet base, fabric, and washer on the die (included). A few sharp taps on the punch cinch the grommet in the hole. Use a rubber or rawhide mallet rather than a metal hammer to preserve the head of the punch.
    Hammer-Driven Cutting Punch—Create a hole in your fabric with a few sharp mallet taps on the cutting punch. Use a rubber or rawhide mallet rather than a metal hammer to preserve the head of the punch.
    For Grommet
    Trade Size
    For Hole
    Dia.
    Material
    Each
    Hammer-Driven Installation Punch
    003/16"—9612K25000000
    01/4"—9612K2600000
    19/32"—9612K2700000
    23/8"—9612K2800000
    37/16"—9612K2900000
    41/2"—9612K3100000
     
    Hammer-Driven Cutting Punch
    003/16"Steel9611K1100000
    01/4"Steel9611K1200000
    19/32"Steel9611K1300000
    23/8"Steel9611K1400000
    37/16"Steel9611K1500000
    41/2"Steel9611K1600000
     
    Manual Presses
    Image of Product. Front orientation. Contains Annotated. Fabric Fastener Installation Tools. Reinforcing, Manual Press.

    Manual Press

    Manual Press—Saves time and effort if you’re frequently installing or replacing grommets. Install the required two-piece die set (sold separately) on the press, align the grommet in the hole, and squeeze the handle. For a longer service life, lubricate the handle and plunger with a drop of oil.
    Throat
    Max.
    Opening
    Dp.
    Wd.
    Material
    Each
    Manual Press
    7/8"3 1/4"1 3/4"Aluminum
    		95720A6900000000
     
    Grommet Dies
    Image of Product. Front orientation. Grommet Dies.
    For Grommet
    Trade Size
    Hole
    Size
    Each
    003/16"95720A710000000
    01/4"95720A71500000
    19/32"95720A72000000
    23/8"95720A73000000
    37/16"95720A74000000
    Rolled Rim with Tooth-Lock Washer
    Image of Product. Front orientation. Contains Annotated. Grommets. Reinforcing Fabric Grommets, Rolled Rim with Tooth-Lock Washer.
    Teeth grip the fabric for an even stronger hold than other reinforcing fabric grommets. Use these washers for fabric under the highest strain, such as a tarp secured by bungee cords.
    Brass—Add a bright finish to your fabric.
    Nickel-Plated Brass—The nickel gives these a more muted, silvery look than our other brass grommets.
    Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.
    Grommet
    Trade Size
    For Max.
    Material Thk.
    ID
    Flange
    Dia.
    Dp. Under
    Flange
    For Use
    Outdoors
    Mil. Spec.
    Pkg.
    Qty.
    Pkg.
    Brass
    00.096"9/32"0.67"0.175"YesAN230, MIL-G-16491, NASM20230509606K41000000
    10.126"13/32"0.79"0.205"YesAN230, MIL-G-16491, NASM20230509606K4200000
    20.174"7/16"0.89"0.255"YesAN230, MIL-G-16491, NASM20230259606K4300000
    30.172"15/32"0.97"0.255"YesAN230, MIL-G-16491, NASM20230259606K4400000
    40.237"9/16"1.12"0.32"YesAN230, MIL-G-16491, NASM20230259606K4500000
    50.296"5/8"1.285"0.38"YesAN230, MIL-G-16491, NASM20230109606K460000
    60.332"3/4"1.535"0.42"YesAN230, MIL-G-16491, NASM2023059606K470000
    70.363"29/32"1.725"0.446"YesAN230, MIL-G-16491, NASM2023059606K4800000
    80.382"1 3/32"1.865"0.465"YesAN230, MIL-G-16491, NASM2023059606K4900000
     
    Nickel-Plated Brass
    00.096"9/32"0.67"0.175"YesAN230, MIL-G-16491, NASM16491, NASM202305087995K5100000
    10.126"13/32"0.79"0.205"YesAN230, MIL-G-16491, NASM16491, NASM202302587995K5200000
    20.174"7/16"0.89"0.255"YesAN230, MIL-G-16491, NASM16491, NASM202302587995K5300000
    30.172"15/32"0.97"0.255"YesAN230, MIL-G-16491, NASM16491, NASM202302587995K5400000
    40.237"9/16"1.12"0.32"YesAN230, MIL-G-16491, NASM16491, NASM202301087995K550000
    50.296"5/8"1.285"0.38"YesAN230, MIL-G-16491, NASM16491, NASM202301087995K5600000
    60.332"3/4"1.535"0.42"YesAN230, MIL-G-16491, NASM16491, NASM20230587995K570000
    70.363"29/32"1.725"0.446"YesAN230, MIL-G-16491, NASM16491, NASM20230587995K5800000
    80.382"1 3/32"1.865"0.465"YesAN230, MIL-G-16491, NASM16491, NASM20230587995K5900000
     
    Accessories for Grommets
    Installation and Cutting Punches
    Image of Product. Front orientation. Fabric Fastener Installation Tools. Reinforcing, Hammer-Driven Installation Punch.

    Hammer-Driven

    Installation

    Punch

    Image of Product. Front orientation. Fabric Fastener Installation Tools. Reinforcing, Hammer-Driven Cutting Punch.

    Hammer-Driven

    Cutting Punch

    Hammer-Driven Installation Punch—The economical choice if you’re installing a few grommets at a time. Align the grommet base, fabric, and washer on the die (included). A few sharp taps on the punch cinch the grommet in the hole. Use a rubber or rawhide mallet rather than a metal hammer to preserve the head of the punch.
    Hammer-Driven Cutting Punch—Create a hole in your fabric with a few sharp mallet taps on the cutting punch. Use a rubber or rawhide mallet rather than a metal hammer to preserve the head of the punch.
    For Grommet
    Trade Size
    For Hole
    Dia.
    Material
    Each
    Hammer-Driven Installation Punch
    09/32"—9612K17000000
    113/32"—9612K1800000
    27/16"—9612K1900000
    315/32"—9612K2100000
    49/16"—9612K2200000
    55/8"—9612K2300000
    63/4"—9612K2400000
    729/32"—9612K35000000
    81 3/32"—9612K36000000
     
    Hammer-Driven Cutting Punch
    01/4"Steel9611K1200000
    19/32"Steel9611K1300000
    23/8"Steel9611K1400000
    37/16"Steel9611K1500000
    41/2"Steel9611K1600000
    55/8"Steel9611K1700000
    63/4"Steel9611K1800000
    77/8"Steel9611K1900000
    81"Steel9611K2100000
     
    Manual Presses
    Image of Product. Front orientation. Contains Annotated. Fabric Fastener Installation Tools. Reinforcing, Manual Press.

    Manual Press

    Manual Press—Saves time and effort if you’re frequently installing or replacing grommets. Install the required two-piece die set (sold separately) on the press, align the grommet in the hole, and squeeze the handle. For a longer service life, lubricate the handle and plunger with a drop of oil.
    Throat
    Max.
    Opening
    Dp.
    Wd.
    Material
    Each
    Manual Press
    7/8"3 1/4"1 3/4"Aluminum
    		95720A6900000000
     
    Grommet Dies
    Image of Product. Front orientation. Grommet Dies.
    For Grommet
    Trade Size
    Hole
    Size
    Each
    09/32"95720A810000000
    113/32"95720A82000000

    Self-Piercing Fabric Grommets

    Save time installing grommets in tarps and covers without precut holes. Set grommets in a bench-mount manual press with die set, and the sharp neck of the grommet cuts the material as you press it into place. Installation tools are sold separately.
    Standard Washer
    Image of Product. Front orientation. Contains Annotated. Grommets. Self-Piercing Fabric Grommets, Standard Washer.
    Grommets with trade size 0, 1, and 2 require a die set adapter for installation.
    Brass—Add a bright finish to your fabric.
    Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.
    Grommet
    Trade Size
    For Max.
    Material Thk.
    ID
    Flange
    Dia.
    Dp. Under
    Flange
    For Use
    Outdoors
    Pkg.
    Qty.
    Pkg.
    Brass
    00.091"1/4"0.562"0.154"No507253K11000000
    10.091"5/16"0.625"0.154"No507253K1200000
    20.091"3/8"0.75"0.154"No507253K1300000
    30.091"7/16"0.938"0.154"No257253K1400000
    40.091"5/8"1.125"0.154"No257253K1500000
     
    Accessories for Grommets
    Manual Presses
    Image of Product. Front orientation. Contains Annotated. Fabric Fastener Installation Tools. Bench-Mount Manual Press.

    Bench-Mount Manual

    Press

    Bench-Mount Manual Press—Saves time and effort if you’re frequently installing or replacing grommets. Install the required two-piece die set (sold separately) on the press, align the grommet in the hole, and squeeze the handle. For a longer service life, lubricate the handle and plunger with a drop of oil.
    Material
    Throat
    Dp.
    Press
    Ht.
    Frame
    Ram
    Mounting Fasteners
    Included
    Each
    Bench-Mount Manual Press
    4 3/4"8"IronSteelNo95715A6900000000
     
    Grommet Dies
    Image of Product. Front orientation. Grommet Dies.
    For Grommet
    Trade Size
    Each
    07253K111000000
    17253K11200000
    27253K11300000
    37253K211000000
    47253K212000000
    Required Adapters for Grommet Dies
    Image of Product. Bottom orientation. Adapters for Grommet Dies.
    For Grommet
    Trade Size
    Each
    0, 1, 27253K33000000
    Tooth-Lock Washer
    Image of Product. Front orientation. Contains Annotated. Grommets. Self-Piercing Fabric Grommets, Tooth-Lock Washer.
    Teeth grip the fabric for a stronger hold than standard washers.
    Brass—Add a bright finish to your fabric.
    Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.
    Grommet
    Trade Size
    For Max.
    Material Thk.
    ID
    Flange
    Dia.
    Dp. Under
    Flange
    For Use
    Outdoors
    Pkg.
    Qty.
    Pkg.
    Brass
    00.126"9/32"0.688"0.189"No508276K41000000
    10.126"3/8"0.75"0.189"No508276K4200000
    20.126"7/16"0.875"0.189"No258276K4300000
    40.126"9/16"1.125"0.189"No108276K440000
     
    Accessories for Grommets
    Manual Presses
    Image of Product. Front orientation. Contains Annotated. Fabric Fastener Installation Tools. Bench-Mount Manual Press.

    Bench-Mount Manual

    Press

    Bench-Mount Manual Press—Saves time and effort if you’re frequently installing or replacing grommets. Install the required two-piece die set (sold separately) on the press, align the grommet in the hole, and squeeze the handle. For a longer service life, lubricate the handle and plunger with a drop of oil.
    Material
    Throat
    Dp.
    Press
    Ht.
    Frame
    Ram
    Mounting Fasteners
    Included
    Each
    Bench-Mount Manual Press
    4 3/4"8"IronSteelNo95715A6900000000
     
    Grommet Dies
    Image of Product. Front orientation. Grommet Dies.
    For Grommet
    Trade Size
    Each
    08276K620000000
    18276K63000000
    28276K64000000
    48276K65000000
    back to top