These pumps provide about 25% more flow than standard float-switch activated pumps for sewage water. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Pumps are equipped with a large intake and rugged impeller to transfer raw sewage water with solids up to 2” in diameter.

Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Equipped with a large intake and rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Equipped with a large intake and rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter.

Pumps have a heavy duty motor with sealed bearings that generates a flow rate similar to our other sump pumps for sewage water while using fewer amps. Connect them to a three-pronged plug or wire them directly to a power source to activate. Pumps transfer raw sewage water with solids up to 2” in diameter.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

The float switch is wired to the pump. Use with debris-free water.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Use with debris-free water.

The intake is 2" from the base of the pump to prevent dirt at the bottom of your sump pit from clogging the pump. Use with debris-free water.

Since the motor is totally enclosed fan cooled (TEFC) and never comes into contact with the water, these pumps can be used with hot water up to 200° F.

Don't let a power outage cause flooding. Powered by water flow in your supply line, these pumps work as a backup to your primary sump pump. Use with debris-free water.

Move higher volumes of water with solids than other sump pumps. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They are often used with liquid waste that has passed through a septic tank, so most solids are removed.

The float switch is wired to the pump. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They're often used with liquid waste that has passed through a septic tank, so most solids are removed.

Use these pumps at temperatures up to 200° F. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. The float switch is adjustable and wired to the discharge pipe.

Kits include tubing, a backflow-prevention valve, an adapter, and a clamp.

An alarm and a red light alert you when water levels rise too high.

Activate your pump in dirty water that contains sludge and sewage.

Since these switches activate on increasing pressure caused by rising water levels, they have no floats to catch on sump pit walls.

Wheel these pumps to remote areas with no power. They can handle sewage water with thick sludge, silt, and debris up to 2” in diameter.

The switch activates on increasing pressure caused by rising water levels for a long service life. It has a separate cord, so you can replace the switch without replacing the whole pump. Use the handle to carry pumps from job to job.

Also known as bilge pumps, these remove fresh and salt water from spots where other pumps don’t fit.

Complete with a suction strainer and 6 feet of garden hose, these little pumps come ready to clean up small open spaces.

An aluminum housing provides excellent impact resistance. Use these pumps to clean up water in flooded areas without a sump pit. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

Clean up water in flooded areas without a sump pit. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

These pumps have an impact-resistant aluminum housing and handle larger solids than other battery-operated water-removal pumps. Use them to remove water from areas without power.

Built with high-chromium stainless steel components, these pumps stand up to salt water with up to 25% sand by volume and resist wear caused by abrasive particles. Fill the fuel tank with gasoline to remove water at sites without power.

With a polypropylene housing, these pumps are about half the weight of other gasoline-powered pumps. Fill the fuel tank with gasoline to remove water at sites without power.

Made from PVC, these pumps are highly corrosion resistant and lightweight. Use them to produce emulsions, elevate water, and transport grains and other small particles.

A cast iron housing and steel gears allow these pumps to be used to dispense oil and fuel such as hydraulic oil and diesel fuel. Also known as gear pumps, they produce a smooth flow of liquid for applications such as engine lubrication.

Mount these pumps in any position, even upside down. Pumps have a subfractional horsepower motor rated for intermittent use. Also known as diaphragm pumps, use them for low-flow spraying, draining, and washdown applications.

With a 316 stainless steel housing and PPS gears, these pumps are often used to dispense chemicals such as ethylene glycol, isopropyl alcohol, and nitric acid. Also known as gear pumps, they produce a smooth flow of liquid.

Commonly called rotary vane pumps, these are designed to pump water at high pressures in low-flow applications. Use at pressures up to 240 psi.

Designed to fit into small equipment, these pumps have miniature gears and a subfractional horsepower motor for low-flow applications.

A high-horsepower motor moves oil with a viscosity similar to SAE 60 motor oil. Also known as gear pumps, these produce a smooth flow of liquid to lubricate equipment and blend oils.

Also known as flexible impeller pumps, these create a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump.