Often used in mining equipment, submersible pumps, and drilling rigs, this cable withstands 2,000 volts AC/DC. The EPDM insulation resists abrasion, so it can be pulled over rough surfaces without damaging the wires inside.

For technical drawings and 3-D models, click on a part number.

This cable has an insulation with excellent resistance to oil, so it can be used near motors and equipment that require oil lubrication. Often used in automated applications such as robotics and cable carriers, it withstands continuous motion without degrading data or signal transmission. It’s flame rated VW-1 to meet requirements for preventing the spread of flames based on a timed test with vertically suspended material.

Use unshielded cable in applications where signal interference is not a concern.

Shielded cable has a layer of braid that blocks signal interference from nearby equipment and devices.

Bend radius is the point to which the cable will bend without being damaged. It is measured from the center of the bend to the edge of the cable. The smaller the measurement, the tighter the bend.

For technical drawings and 3-D models, click on a part number.

This cable meets TC-ER crush and impact requirements for exposed runs in cable carriers, so it can be used without conduit. It withstands periodic flexing and bending, sends signal and data to operate, measure, or regulate automated equipment. The PVC insulation resists oil. It’s flame rated FT4 to meet requirements for preventing the spread of flames based on a timed test with material mounted to a vertical tray.

Use unshielded cable in applications where signal interference is not a concern.

Double shielded cable has a layer of braid and foil shielding that provides excellent protection against signal interference from nearby equipment and devices.

This cable withstands abrasion, oil, and the rough conditions found in welding applications. It’s flame rated VW-1 to meet requirements for vertical flame testing.

Class K cable is for general purpose welding applications. It bends and stays in the position that you bend it.

Class M cable is more flexible and durable than Class K cable.

This cable meets Mine Safety and Health Administration (MSHA) standards for flame resistance. It’s also flame rated VW-1 to meet requirements for preventing the spread of flames, based on a timed test with vertically suspended material. The insulation resists abrasion and chemicals.

Even at 480° F—hotter than some industrial ovens—this wire’s insulation won’t melt.

Wire with a fiberglass outer and mica inner insulation is the common choice for steel mills, iron mills, and glass manufacturing. You may know it as MG wire.

Connect batteries in vehicles and generators.

Strand count is the number of strands followed by the size of the individual strand.

Wire with a PVC plastic insulation resists fuel and oil.

Wire with an EPDM rubber insulation is ultra-flexible for use in applications that require tight turns. The insulation resists abrasion and oil.

Wire with a cross-linked polyolefin (XLPO) insulation is ultra-flexible and withstands high heat, making it suitable for applications such as vehicle engine wiring.

SAE wire meets standards for low-voltage wiring in vehicle electrical systems.

For technical drawings and 3-D models, click on a part number.

Connect batteries in generators, forklifts, and other vehicles in corrosive environments. Also known as marine wire, this copper wire is tin plated to resist corrosion from salt water, battery acid, and oil. Designed for boats, it's a good choice for use outdoors. The PVC insulation stands up to fuel and oil. Strand count is the number of strands followed by the size of the individual strand.

For technical drawings and 3-D models, click on a part number.

Insulated with TPE, this wire won’t break down from oil, coolant, or chemicals, and it carries a strong signal even when repeatedly bent. This makes it great for greasy equipment on automated lines, such as lubricated cable carriers. Its insulation also stands up to moisture and sunlight, so you can use this wire outdoors. This wire is flame rated FT1, which means it meets requirements for preventing the spread of fire.

Unshielded wire works in most applications. You can twist it 90° while pulling and bending it at the same time.

Choose shielded wire if you need protection against signal interference from nearby equipment, such as variable frequency drives or small motors. Spiral-shielded wire balances good signal interference and flexibility. It's the most flexible wire we offer, so it will bend, flex, and twist 180° without stretching or snapping.

Install this copper wire in conduit and cable trays in commercial and industrial buildings. It's also known as branch circuit wire. The outer jacket is designed to be installed without applying pulling lubricant.

Stranded wire is flexible, so it’s pliable enough to be pulled around corners. Wire with a nylon outer insulation resists oil and water. THHN wire can be used in dry or damp locations where wire is exposed to condensation or moisture, such as a basement. THWN and THWN-2 wire can be used in both wet and dry environments.

Flame rated VW-1 wire meets requirements for preventing the spread of flames based on a timed test with vertically suspended material.

For technical drawings and 3-D models, click on a part number.

The EPDM insulation on this wire won’t become brittle or crack from sunlight, humidity, rain, temperature changes, abrasion from dirt and debris, and other rough outdoor conditions. It meets Mine Safety and Health Administration (MSHA) standards for material quality.

SC wire is a good choice for temporary setups powering outdoor lights, equipment, generators, and power distribution boxes, since its thick insulation makes it easy to move and reuse. Commonly found at outdoor events, it’s also known as stage cable.

DLO wire carries higher voltages than SC wire, making it the better choice for heavy duty applications. Use it to run power to motors, cranes, and other equipment in shipyards, mines, and oil- and gas-drilling rigs. Also known as diesel locomotive cable, this wire was originally designed to wire trains. An outer layer of chlorinated polyethylene plastic (CPE) gives it increased resistance to chemicals, heat, and flames. It’s also rated RHW-2, so it can be used underground and in wet locations.

All are flame rated, so they meets requirements for preventing the spread of flames based on a timed test. FT4 wire is mounted to a vertical tray during testing. FT5 wire is suspended horizontally during testing.

Mend or extend aluminum wire often found in older buildings. This wire isn’t recommended for new wiring, since it’s more likely to overheat than copper when conducting electricity. However, it’s safer to maintain existing aluminum wire with aluminum rather than mixing materials. Building wire is also known as branch circuit wire.

This wire has an outer layer of nylon insulation that won't degrade from oil and water. It’s designed to be pulled through conduit without pulling lubricants. THHN and THWN-2 designated, this wire can be used in damp places.

For technical drawings and 3-D models, click on a part number.