Use this general purpose cable to supply power to equipment.

This cable can be stretched by about 40% and return to its original length, making it useful for applications where cable is in motion. It's often sewn into garments or used with equipment that must be worn.

For high-heat applications such as furnaces and ovens, this cable's insulation withstands temperatures of 390° F and higher.

A thick rubber insulation resists cuts and abrasion, so this cable can be pulled over rough surfaces without damaging the wires inside.

Weather-resistant insulation makes this cable suitable for outdoor use and direct burial without conduit.

Supply power to submersible pumps in water or oil wells.

Often used in automated applications such as robotics and cable carriers, this cable withstands continuous motion without degrading data or signal transmission.

Use this cable without conduit in automated applications—it meets crush and impact requirements for exposed runs in cable carriers, and withstands continuous motion without degrading data or signal transmission.

With a life span of more than 20 million high-speed flex cycles, this cable lasts twice as long as standard continuous-flex cable. The frequent motion will not degrade data or signal transmission.

For use in tight spaces, this cable has up to a 40% smaller OD than standard continuous-flex cable. It withstands continuous motion without degrading data or signal transmission.

Send signal and data to operate, measure, or regulate automated equipment such as conveyors and CNC machines.

Nearly two-thirds the diameter of standard control cable, this cable fits in tight spaces. It sends signal and data to operate, measure, or regulate automated equipment.

Often used in electronic prototyping or in the interior of computers, this flat cable is ultra flexible with small-gauge wires so it fits in tight spaces.

Connect low-current circuits such as intercoms and security systems to a building's electrical system in single-level facilities.

After extending to full length to provide added reach, this cable retracts and self-coils for tangle-free storage. It's often used with low-current circuits such as microphones and headsets.

The metal armor on this cable acts as conduit to protect the internal wires. It's often used along the exterior of walls to carry power to outlet boxes. Also known as MC cable.

This cable has an uninsulated ground wire that touches the protective metal armor so it can be used for bonding and grounding. It's often used along the exterior of walls to carry power to outlet boxes. Also known as AC cable.

Hook up thermostats, air-conditioning units, and other low-voltage equipment.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. Use in critical circuits such as fire alarms and smoke detectors.

Send data between computers, printers, servers, and switches.

From mines and factories to robotics, this rugged Ethernet cable sends data between sensors and switches in the grimiest places.

Hook up speakers, intercoms, and other low-current devices to a building's communication wiring.

This cable withstands abrasion, oil, and the rough conditions found in welding applications.

Also known as hook-up wire, this wire is primarily used for wiring electrical panels, lighting, and plant floor equipment.

Maintain a supply of Mil. Spec. wire in multiple colors.

More flexible than standard wire, this wire is often used for internal appliance wiring and machine tools. Also known as MTW wire.

Rated to 50 volts AC/DC, this wire is often used in small electronics and robotics. It withstands temperatures of 390° F and greater.

Run power over rough surfaces—this wire has thick insulation that stands up to wear and tear.

The PEEK insulation on this wire won't degrade when exposed to radiation, and is often used in nuclear energy production.

Nearly half the diameter and up to 40% lighter than standard wire of the same gauge and voltage, this wire fits in tight spaces.

Connect batteries in vehicles and generators.

Connect batteries in generators, forklifts, and other vehicles in corrosive environments. Also known as marine wire, this copper wire is tin plated to resist corrosion from salt water, battery acid, and oil.

Use this wire in automated applications that require 14,000 volts A/C or greater. It withstands continuous motion without degrading data or signal transmission.

Insulated with TPE, this wire won’t break down from oil, coolant, or chemicals, and it carries a strong signal even when repeatedly bent. This makes it great for greasy equipment on automated lines, such as lubricated cable carriers.

The EPDM insulation on this wire won’t become brittle or crack from sunlight, humidity, rain, temperature changes, abrasion from dirt and debris, and other rough outdoor conditions.

Assortments include wire in multiple lengths and colors.

This wire wraps around a post terminal on a circuit board to make an electrical connection, eliminating the need for soldering.

Use these cords with computers, lab equipment, and office machines that have IEC connections.

Create a vibration-resistant connection—the socket on these cords securely locks onto any male receptacle and will not detach until manually unlocked.

Tug these cords to full length, and they’ll stay plugged in. Also called hospital-grade cords, they form an extra-tight connection with outlets. After stretching, they return to a tight, tangle-free coil.

Power multiple devices from one power source.

The threaded ends on these cords seal out contaminants and resist coming loose from vibration in tough industrial environments and automated systems while sending power and signal to devices with M12 connections.

With a single cord, these splitters join two devices with M12 connectors to a distribution block or I/O module with M12 connectors. Often used with sensors and actuators, they send signals/power to your devices through one connection.

TPE insulation protects these cords from some of the toughest industrial conditions, including abrasion, coolants, chemicals, UV rays, and weld slag. Use them in areas with welding, machining, and fluctuating temperatures to send signal and power to M12 proximity switches, valves, and other devices.

Connect two devices to a distribution block or I/O module with just one cord. Often used with sensors and actuators, these splitters send power/signals to your devices through a single connection.

With a higher maximum current than nano M8 and micro M12 cords, these mini cords are often used with automated systems, motors, and pumps.

These cords have an M8 connector on one end and an M12 connector on the other.

Use these unshielded cords where signal interference is not a concern.

To send high-speed data in tough, rugged environments, these cords have an M12 connector on one end that threads onto switches, sensors, and other devices prone to vibration. The other end has a traditional RJ45 plug that connects to Ethernet equipment, such as computers, IO modules, and programmable logic controllers (PLCs).

The M12 threaded connectors on these cords are more vibration resistant than RJ45 connectors.

With a flange on the socket end, you can mount these cords in a panel cutout to move data between computers, printers, and mobile devices.

Adapt your USB port to connect to a variety of other devices.