Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Also known as 4-way and 5/2 valves, these valves create two actions, such as extending and then retracting a double-acting cylinder. Apply voltage to the electrical connection to actuate.

Run through equipment cycles up to 30% faster than with standard valves. Also known as 3/2 valves, they create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate.

Create two actions at the same time, such as extending two single-acting cylinders at once. Apply voltage to the electrical connection to actuate. Also known as pressure center valves.

Ceramic plates form a longer-lasting seal against oil and dust than rubber seals that deteriorate over time. These valves withstand use in corrosive, dusty, and dirty environments such as foundries, paper mills, and steel plants. Apply voltage to the electrical connection to actuate.

Rated IP69K, these valves withstand high-pressure, high-temperature washdowns. Their smooth design keeps out dust, dirt, and contaminants, making them easier to keep clean. Apply voltage to the electrical connection to actuate.

Mount valves to a single-station base or to a manifold, which allows a single pressure source for multiple valves, then add or remove valves as your needs change.

Also known as solenoid valves, these valves are operated by an electrical signal to turn airflow on or off.

Install these valves on your air tank outlet—at the end of the day, they automatically close to save energy.

Set the electronic timer on these drain valves to open automatically at your specified time interval.

These withstand at least double the pressure of our other timer-operated drain valves.

Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.

Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.

These solenoid valves operate on electricity to automatically start and stop flow. The actuator is directly mounted to the valve body to minimize movement and reduce wear.

Lower profile and available in smaller connection sizes than standard valves, these fit in tight spots.

Less than half the size of our other compact valves, these have small pipe connections for miniature lines.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Designed for controlling single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

For use in general purpose applications with water, oil, and inert gas.

Limit wear and damage in high-cycling applications—these valves have additional seals that prevent leakage to reduce maintenance time.

Their ball-valve design allows these valves to handle three times the flow of butterfly valves.

With a slimmer motor than other motor-driven valves, these fit in tight spots.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

Their ball valve design allows these valves to handle three times the flow of butterfly valves.

Often used for emission analysis and gas processing, these valves attach to each other horizontally to create one centralized manifold for servicing multiple process lines. All are rated for use with water, oil, air, and inert gas. They operate on electricity to automatically divert flow between ports.

Lower profile than other solenoid diverting valves and available in smaller pipe sizes, these valves are often used to automatically divert flow between ports in tight spots. Use them with water, oil, air, and inert gas. All operate on electricity.

For use with threaded pipe, these valves have NPT connections. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.