Filter by
Ball Bearing Profile
ID
Width
For Housing ID
Bearing Trade Number
Inner Ring Width
Cage Material
Lubrication
Dynamic Radial Load Capacity
Ball Material
Maximum Rotation Speed
Inner Ring OD
DFARS Specialty Metals
Performance
Ball Bearing Profile
Quick-Mount Ball Bearings
Slip onto a shaft and secure with the turn of a screw. You don't need any special tools to mount these bearings.
Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place. For high-speed applications, consider clamp-on shaft mounts, which are less likely to slip.
Clamp-On Shaft Mount—The clamp tightens around the shaft for a strong 360° grip. These mounts attach more securely than set screws to reduce vibration. Plus, there aren't any screws pressing into the shaft, so it stays free from damage. Also known as a concentric lock.
Steel and Black-Oxide Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.
Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
Retaining Ring | Temp. Range, ° F | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | OD | Thk. | Bearing Seal Type | ABEC Rating | Dynamic Radial Load Cap., lb. | Max. Rotation Speed, rpm | Min. | Max. | Bearing Trade No. | Each | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Set-Screw Shaft Mount | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/2" | 1 3/4" | 5/8" | 1.922" | 0.042" | Sealed | Not Rated | 2,550 | 5,000 | -20 | 250 | 7608-2RS | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
9/16" | 1 3/4" | 5/8" | 1.922" | 0.042" | Sealed | Not Rated | 2,550 | 5,000 | -20 | 250 | 7609-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/8" | 1 3/4" | 5/8" | 1.922" | 0.042" | Sealed | Not Rated | 2,550 | 5,000 | -20 | 250 | 7610-2RS | 000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
11/16" | 1 3/4" | 5/8" | 1.922" | 0.042" | Sealed | Not Rated | 2,550 | 5,000 | -20 | 250 | 7611-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/4" | 1 3/4" | 5/8" | 1.922" | 0.042" | Sealed | Not Rated | 2,550 | 5,000 | -20 | 250 | 7612-2RS | 000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
13/16" | 2" | 5/8" | 2.156" | 0.042" | Sealed | Not Rated | 2,950 | 5,000 | -20 | 250 | 7613-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
7/8" | 2" | 5/8" | 2.156" | 0.042" | Sealed | Not Rated | 2,950 | 5,000 | -20 | 250 | 7614-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
15/16" | 2" | 5/8" | 2.156" | 0.042" | Sealed | Not Rated | 2,950 | 5,000 | -20 | 250 | 7615-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1" | 2" | 5/8" | 2.156" | 0.042" | Sealed | Not Rated | 2,950 | 5,000 | -20 | 250 | 7616-2RS | 000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/16" | 2 9/16" | 3/4" | 2.766" | 0.065" | Sealed | Not Rated | 5,350 | 5,000 | -20 | 250 | 7617-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/8" | 2 9/16" | 3/4" | 2.766" | 0.065" | Sealed | Not Rated | 5,350 | 5,000 | -20 | 250 | 7618-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/4" | 2 9/16" | 3/4" | 2.766" | 0.065" | Sealed | Not Rated | 5,350 | 5,000 | -20 | 250 | 7620-2RS | 000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Black-Oxide Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/2" | 1 27/32" | 5/8" | 2.063" | 0.047" | Shielded | 1 | 3,200 | 9,200 | -40 | 250 | ER8 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/8" | 1 27/32" | 5/8" | 2.063" | 0.047" | Sealed | Not Rated | 2,850 | 5,000 | -20 | 250 | ER10 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/4" | 1 27/32" | 5/8" | 2.063" | 0.047" | Sealed | Not Rated | 2,850 | 5,000 | -20 | 250 | ER12 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
7/8" | 2 3/64" | 3/4" | 2.266" | 0.047" | Shielded | 1 | 3,450 | 7,800 | -40 | 250 | ER14 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
15/16" | 2 3/64" | 3/4" | 2.266" | 0.047" | Sealed | 1 | 2,800 | 6,350 | -20 | 220 | ER15 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1" | 2 3/64" | 3/4" | 2.266" | 0.047" | Sealed | Not Rated | 3,100 | 5,000 | -20 | 250 | ER16 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/16" | 2 7/16" | 7/8" | 2.656" | 0.063" | Sealed | 1 | 4,350 | 5,450 | -20 | 220 | ER17 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/8" | 2 7/16" | 7/8" | 2.656" | 0.063" | Sealed | 1 | 4,850 | 6,100 | -65 | 250 | ER18 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 3/16" | 2 7/16" | 7/8" | 2.656" | 0.063" | Sealed | Not Rated | 4,350 | 5,000 | -20 | 250 | ER19 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/4" | 2 27/32" | 15/16" | 3.078" | 0.063" | Sealed | Not Rated | 5,750 | 5,000 | -20 | 250 | ER20 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 3/8" | 2 27/32" | 15/16" | 3.078" | 0.063" | Shielded | 1 | 6,400 | 5,000 | -40 | 250 | ER22 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 7/16" | 2 27/32" | 15/16" | 3.078" | 0.063" | Sealed | Not Rated | 5,750 | 5,000 | -20 | 250 | ER23 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/2" | 3 5/32" | 1 3/32" | 3.406" | 0.063" | Sealed | Not Rated | 6,500 | 5,000 | -20 | 250 | ER24 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 5/8" | 3 11/32" | 1 3/32" | 3 19/32" | 0.063" | Sealed | 1 | 7,900 | 3,800 | -20 | 220 | ER26 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 11/16" | 3 11/32" | 1 3/32" | 3 19/32" | 0.063" | Sealed | 1 | 7,900 | 3,800 | -20 | 220 | ER27 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 3/4" | 3 11/32" | 1 3/32" | 3.578" | 0.063" | Shielded | 1 | 8,150 | 3,900 | -40 | 250 | ER28 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 15/16" | 3 35/64" | 1 1/8" | 3.781" | 0.094" | Sealed | Not Rated | 7,900 | 5,000 | -20 | 250 | ER31 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2" | 3 15/16" | 1 3/16" | 4.188" | 0.094" | Shielded | 1 | 10,800 | 3,400 | -40 | 250 | ER32 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2 3/16" | 3 15/16" | 1 3/16" | 4 3/16" | 0.094" | Sealed | 1 | 9,750 | 3,250 | -20 | 220 | ER35 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2 1/4" | 4 21/64" | 1 1/4" | 4 37/64" | 0.094" | Sealed | 1 | 11,750 | 3,000 | -20 | 220 | ER36 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2 3/8" | 4 21/64" | 1 1/4" | 4 37/64" | 0.094" | Sealed | 1 | 11,750 | 3,000 | -20 | 220 | ER38 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2 7/16" | 4 21/64" | 1 1/4" | 4 37/64" | 0.094" | Sealed | 1 | 11,750 | 3,000 | -20 | 220 | ER39 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2 1/2" | 4 59/64" | 1 3/8" | 5 9/32" | 0.109" | Sealed | 1 | 13,950 | 2,500 | -20 | 220 | ER40 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3" | 5 33/64" | 1 11/16" | 5 13/16" | 0.109" | Sealed | 1 | 17,400 | 2,250 | -20 | 220 | ER48 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
20 mm | 47 mm | 15.9 mm | 52.4 mm | 1.2 mm | Sealed | 1 | 2,600 | 7,300 | -20 | 220 | ER204 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
25 mm | 52 mm | 19.1 mm | 57.5 mm | 1.2 mm | Sealed | 1 | 2,800 | 6,350 | -20 | 220 | ER205 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
30 mm | 62 mm | 22.2 mm | 67.5 mm | 1.6 mm | Sealed | 1 | 4,350 | 5,450 | -20 | 220 | ER206 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
35 mm | 72 mm | 23.8 mm | 78.2 mm | 1.6 mm | Sealed | 1 | 5,750 | 4,650 | -20 | 220 | ER207 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
40 mm | 80 mm | 27.8 mm | 86.5 mm | 1.6 mm | Sealed | 1 | 7,300 | 4,150 | -20 | 220 | ER208 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
50 mm | 90 mm | 28.6 mm | 96 mm | 2.4 mm | Sealed | 1 | 7,850 | 3,550 | -20 | 220 | ER210 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
70 mm | 125 mm | 34.9 mm | 134.1 mm | 2.8 mm | Sealed | 1 | 13,950 | 2,500 | -20 | 220 | ER214 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Clamp-On Shaft Mount | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Black-Oxide Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/4" | 1 27/32" | 5/8" | 2.063" | 0.047" | Sealed | 1 | 2,600 | 10,200 | -20 | 220 | ER12 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1" | 2 1/16" | 3/4" | 2.266" | 0.047" | Sealed | 1 | 2,800 | 9,000 | -20 | 220 | ER16 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/4" | 2 7/16" | 7/8" | 2.656" | 0.063" | Sealed | 1 | 4,350 | 7,600 | -20 | 220 | ER20 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/4" | 2 27/32" | 15/16" | 3.078" | 0.063" | Sealed | 1 | 5,750 | 6,500 | -20 | 220 | ER20 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 7/16" | 2 27/32" | 15/16" | 3.078" | 0.063" | Sealed | 1 | 5,750 | 6,500 | -20 | 220 | ER23 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/2" | 3 5/32" | 1 3/32" | 3.406" | 0.063" | Sealed | 1 | 7,300 | 5,850 | -20 | 220 | ER24 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2" | 3 15/16" | 1 3/16" | 4.188" | 0.094" | Sealed | 1 | 9,750 | 4,500 | -20 | 220 | ER32 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
20 mm | 47 mm | 16 mm | 52 mm | 1.2 mm | Shielded | 1 | 2,600 | 6,450 | -20 | 220 | ER204 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
25 mm | 52 mm | 19 mm | 58 mm | 1.2 mm | Shielded | 1 | 2,800 | 6,350 | -20 | 220 | ER205 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
30 mm | 62 mm | 22 mm | 68 mm | 1.6 mm | Shielded | 1 | 4,350 | 5,450 | -20 | 220 | ER206 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
40 mm | 80 mm | 28 mm | 88 mm | 1.6 mm | Shielded | 1 | 7,300 | 4,150 | -20 | 220 | ER208 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
45 mm | 85 mm | 28 mm | 91 mm | 1.6 mm | Shielded | 1 | 7,900 | 3,800 | -20 | 220 | ER209 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Insert Bearings
![]() |
Install by hand into a housing (sold separately) |
![]() |
Swap out worn inserts instead of replacing the entire mounted unit. To choose an insert, match the manufacturer model number on your existing bearing.
Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place, regardless of the direction the shaft spins.
ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
Temp. Range, ° F | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Mounted Bearing Model No. | Bearing Material | ABEC Rating | Min. | Max. | Each | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
For Timken Mounted Bearings | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Set-Screw Shaft Mount | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/2" | SAK 1/2, SAS 1/2, SCJ 1/2, SCJT 1/2 | Steel | 1 | -65 | 250 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/8" | SAK 5/8, SAS 5/8, SCJ 5/8, SCJT 5/8 | Steel | 1 | -65 | 250 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/4" | SAK 3/4, SAS 3/4, SCJ 3/4, SCJT 3/4, STB 3/4 | Steel | 1 | -65 | 250 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1" | SAK 1, SAS 1, SCJ 1, SCJT 1, STB 1 | Steel | 1 | -65 | 250 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 3/16" | SAK 1 3/16, SAS 1 3/16, SCJ 1 3/16, SCJT 1 3/16, STB 1 3/16 | Steel | 1 | -65 | 250 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/4" | SAK 1 1/4, SAS 1 1/4, SCJ 1 1/4, SCJT 1 1/4, STB 1 1/4 | Steel | 1 | -65 | 250 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/4" | SAK 1 1/4 S, SAS 1 1/4 S, SCJ 1 1/4 S, STB 1 1/4 S | Steel | 1 | -65 | 250 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 7/16" | SAK 1 7/16, SAS 1 7/16, SCJ 1 7/16, SCJT 1 7/16, STB 1 7/16 | Steel | 1 | -65 | 250 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/2" | SAK 1 1/2, SAS 1 1/2, SAS 1 1/2 H, SCJ 1 1/2, SCJT 1 1/2, STB 1 1/2 | Steel | 1 | -65 | 250 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 5/8" | SAK 1 5/8, SAS 1 5/8, SCJ 1 5/8, SCJT 1 5/8, STB 1 5/8 | Steel | 1 | -65 | 250 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 11/16" | SAK 1 11/16, SAS 1 11/16, SCJ 1 11/16, SCJT 1 11/16, STB 1 11/16 | Steel | 1 | -65 | 250 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 3/4" | SAK 1 3/4, SAS 1 3/4, SCJ 1 3/4, SCJT 1 3/4, STB 1 3/4 | Steel | 1 | -65 | 250 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2" | SAK 2 S, SAS 2 S, SCJ 2 S, SCJT 2 S | Steel | 1 | -65 | 250 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
25 mm | SAK 25, SAS 25, SCJ 25, SCJT 25, STB 25 | Steel | 1 | -65 | 250 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
30 mm | SAK 30, SAS 30, SCJ 30, SCJT 30, STB 30 | Steel | 1 | -65 | 250 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
35 mm | SAK 35, SAS 35, SCJ 35, SCJT 35, STB 35 | Steel | 1 | -65 | 250 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Ball Bearings
![]() |
Shielded |
Smoother than smooth—the balls inside these bearings roll nearly friction free. You’ll often find them on rapidly rotating parts, from the whirring chuck on a power drill to the spinning shaft on an electric motor.
Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.
Corrosion-Resistant 440C Stainless Steel—Combine the strength of steel with the corrosion resistance of stainless steel. These bearings won't degrade from water or mild chemicals, such as the ammonia in cleaning solutions. However, they'll weaken when exposed to salt water and harsh chemicals, such as bleach.
Extended Inner Ring—Connect to mating parts without the need for a spacer. The inner ring juts out farther than the outer ring, so shaft collars and other objects won't touch the bearing's moving parts.
ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
Temp. Range, ° F | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | ABEC Rating | Dynamic Radial Load Cap., lb. | Max. Rotation Speed, rpm | Min. | Max. | Inner Ring Type | Bearing Trade No. | Each | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Shielded | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Corrosion-Resistant 440C Stainless Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
0.055" | 3/16" | 7/64" | 5 | 50 | 110,000 | -40 | 240 | Extended | R1-2Z | 00000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/64" | 1/4" | 9/64" | 5 | 70 | 80,000 | -40 | 240 | Extended | R1-4-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/32" | 3/16" | 3/32" | 5 | 30 | 95,000 | -40 | 240 | Extended | R133-2Z | 00000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/32" | 5/16" | 9/64" | 5 | 120 | 71,000 | -40 | 240 | Extended | R1-5-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/8" | 1/4" | 7/64" | 5 | 60 | 80,000 | -40 | 240 | Extended | R144-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/8" | 5/16" | 9/64" | 5 | 120 | 71,000 | -40 | 240 | Extended | R2-5-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/8" | 3/8" | 9/64" | 5 | 140 | 63,000 | -40 | 240 | Extended | R2-6-2Z | 00000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/32" | 5/16" | 1/8" | 5 | 80 | 63,000 | -40 | 240 | Extended | R155-2Z | 00000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/16" | 5/16" | 1/8" | 5 | 80 | 63,000 | -40 | 240 | Extended | R156-2Z | 00000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/16" | 3/8" | 1/8" | 5 | 160 | 60,000 | -40 | 240 | Extended | R166-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/16" | 1/2" | 0.196" | 5 | 290 | 50,000 | -40 | 240 | Extended | R3-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/4" | 3/8" | 1/8" | 5 | 80 | 56,000 | -40 | 240 | Extended | R168-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/4" | 1/2" | 3/16" | 5 | 240 | 50,000 | -40 | 240 | Extended | R188-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/4" | 5/8" | 0.196" | 5 | 330 | 45,000 | -40 | 240 | Extended | R4-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/16" | 1/2" | 5/32" | 5 | 120 | 48,000 | -40 | 240 | Extended | R1810-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Light Duty Flanged Ball Bearings
Reduce friction and withstand jostling in rotating parts that don’t require high speed or precision, such as the shafts in hand cranks and casters. The flange presses against the housing wall, so vibration and other sudden forces parallel to the shaft (thrust loads) won't knock them off-kilter.
Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.
Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
Extended Inner Ring—Connect to mating parts without the need for a spacer. The inner ring juts out farther than the outer ring, so shaft collars and other objects won't touch the bearing's moving parts.
Flange | Temp. Range, ° F | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | OD | Thk. | ABEC Rating | Dynamic Radial Load Cap., lb. | Max. Rotation Speed, rpm | Min. | Max. | Inner Ring Type | Each | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Open | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/4" | 11/16" | 1/4" | 0.807" | 0.05" | Not Rated | 330 | 1,200 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/4" | 7/8" | 1/4" | 1" | 0.05" | Not Rated | 400 | 1,200 | -20 | 250 | Extended | 00000000 | 0000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/16" | 7/8" | 1/4" | 1" | 0.05" | Not Rated | 420 | 1,200 | -20 | 250 | Extended | 00000000 | 0000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/8" | 1 1/16" | 3/8" | 1.182" | 0.06" | Not Rated | 630 | 1,200 | -20 | 250 | Extended | 00000000 | 0000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/8" | 1 1/8" | 3/8" | 1.25" | 0.06" | Not Rated | 630 | 1,200 | -20 | 250 | Extended | 00000000 | 0000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
7/16" | 1 1/16" | 3/8" | 1.182" | 0.06" | Not Rated | 630 | 1,200 | -20 | 250 | Extended | 00000000 | 0000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/2" | 1 1/8" | 3/8" | 1.25" | 0.06" | Not Rated | 310 | 1,000 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/2" | 1 3/8" | 7/16" | 1.5" | 0.06" | Not Rated | 450 | 1,000 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/2" | 1 1/2" | 5/8" | 1.625" | 0.06" | Not Rated | 1,300 | 1,200 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/2" | 1 3/4" | 9/16" | 1.875" | 0.06" | Not Rated | 1,400 | 1,200 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/8" | 1 3/8" | 7/16" | 1.5" | 0.06" | Not Rated | 450 | 1,000 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/8" | 1 1/2" | 7/16" | 1.625" | 0.06" | Not Rated | 1,300 | 1,200 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/4" | 1 3/4" | 9/16" | 1.875" | 0.06" | Not Rated | 1,550 | 1,200 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1" | 2" | 1/2" | 2.125" | 0.06" | Not Rated | 820 | 1,000 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Sealed | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/4" | 11/16" | 5/16" | 0.813" | 0.06" | Not Rated | 250 | 2,500 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/16" | 7/8" | 11/32" | 1" | 0.06" | Not Rated | 320 | 2,500 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/8" | 7/8" | 11/32" | 1" | 0.06" | Not Rated | 320 | 2,500 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/8" | 29/32" | 11/32" | 1" | 0.06" | Not Rated | 350 | 2,500 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/8" | 1 1/8" | 3/8" | 1.25" | 0.06" | Not Rated | 600 | 2,500 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/2" | 1 1/8" | 3/8" | 1.25" | 0.06" | Not Rated | 310 | 1,000 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/2" | 1 3/8" | 7/16" | 1.5" | 0.06" | Not Rated | 450 | 1,000 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/8" | 1 3/8" | 7/16" | 1.5" | 0.06" | Not Rated | 450 | 1,000 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/4" | 1 5/8" | 1/2" | 1.75" | 0.06" | Not Rated | 1,300 | 2,500 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/4" | 1 3/4" | 1/2" | 1.875" | 0.06" | Not Rated | 1,300 | 2,500 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/4" | 2" | 9/16" | 2.125" | 0.06" | Not Rated | 1,450 | 2,500 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1" | 2" | 1/2" | 2.125" | 0.06" | Not Rated | 820 | 1,000 | -20 | 250 | Extended | 00000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Flanged Ball Bearings
![]() |
Shielded |
Install these bearings inside a housing and they won't budge. The flange presses against the housing wall, so vibration and other sudden forces parallel to the shaft (thrust loads) won't knock them off-kilter.
Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.
Corrosion-Resistant 440C Stainless Steel—Combine the strength of steel with the corrosion resistance of stainless steel. These bearings won't degrade from water or mild chemicals, such as the ammonia in cleaning solutions. However, they'll weaken when exposed to salt water and harsh chemicals, such as bleach.
Extended Inner Ring—Connect to mating parts without the need for a spacer. The inner ring juts out farther than the outer ring, so shaft collars and other objects won't touch the bearing's moving parts.
ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
Flange | Temp. Range, ° F | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | OD | Thk. | ABEC Rating | Dynamic Radial Load Cap., lb. | Max. Rotation Speed, rpm | Min. | Max. | Inner Ring Type | Bearing Trade No. | Each | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Shielded | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Corrosion-Resistant 440C Stainless Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/64" | 5/32" | 3/32" | 0.203" | 0.03" | 5 | 30 | 120,000 | -20 | 250 | Extended | R0-2Z | 00000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/64" | 1/4" | 9/64" | 0.296" | 0.03" | 5 | 70 | 80,000 | -20 | 250 | Extended | R1-4-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/32" | 3/16" | 3/32" | 0.234" | 0.03" | 5 | 30 | 95,000 | -20 | 250 | Extended | R133-2Z | 000000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/32" | 5/16" | 9/64" | 0.359" | 0.03" | 5 | 120 | 71,000 | -20 | 250 | Extended | R1-5-2Z | 000000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/8" | 1/4" | 7/64" | 0.296" | 0.03" | 5 | 60 | 80,000 | -20 | 250 | Extended | R144-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/8" | 5/16" | 9/64" | 0.359" | 0.03" | 5 | 120 | 71,000 | -20 | 250 | Extended | R2-5-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/8" | 3/8" | 9/64" | 0.422" | 0.03" | 5 | 140 | 63,000 | -20 | 250 | Extended | R2-6-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/32" | 5/16" | 1/8" | 0.359" | 0.04" | 5 | 80 | 63,000 | -20 | 250 | Extended | R155-2Z | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/16" | 5/16" | 1/8" | 0.359" | 0.04" | 5 | 80 | 63,000 | -20 | 250 | Extended | R156-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/16" | 3/8" | 1/8" | 0.422" | 0.03" | 5 | 160 | 60,000 | -20 | 250 | Extended | R166-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/4" | 3/8" | 1/8" | 0.422" | 0.04" | 5 | 80 | 56,000 | -20 | 250 | Extended | R168-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/4" | 1/2" | 3/16" | 0.547" | 0.05" | 5 | 240 | 50,000 | -20 | 250 | Extended | R188-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/16" | 1/2" | 5/32" | 0.547" | 0.03" | 5 | 120 | 48,000 | -20 | 250 | Extended | R1810-2Z | 000000000 | 0000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Light Duty Ball Bearings
![]() |
Sealed |
Reduce friction between rotating parts that don’t require high speed or precision, such as the shafts in hand cranks and casters.
Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
Extended Inner Ring—Connect to mating parts without the need for a spacer. The inner ring juts out farther than the outer ring, so shaft collars and other objects won't touch the bearing's moving parts.
Temp. Range, ° F | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | ABEC Rating | Dynamic Radial Load Cap., lb. | Max. Rotation Speed, rpm | Min. | Max. | Inner Ring Type | Bearing Trade No. | Each | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Sealed | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/2" | 1 3/4" | 5/8" | Not Rated | 2,550 | 5,000 | -20 | 250 | Extended | 7508-2RS | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/8" | 1 3/4" | 5/8" | Not Rated | 2,550 | 5,000 | -20 | 250 | Extended | 7510-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/4" | 1 3/4" | 5/8" | Not Rated | 2,550 | 5,000 | -20 | 250 | Extended | 7512-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1" | 2" | 5/8" | Not Rated | 2,950 | 5,000 | -20 | 250 | Extended | 7516-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/4" | 2 9/16" | 3/4" | Not Rated | 5,350 | 5,000 | -20 | 250 | Extended | 7520-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Quick-Mount Ball Bearings for Food and Beverage
You don't need any special tools to install these bearings in food production areas. Slip them onto a shaft and secure with the turn of a screw for easy mounting. Greased with NSF-registered H1 lubricant, these bearings are safe to install on food-processing equipment, such as conveyor belts, so long as they don’t directly touch the food. They're IP69K rated, so they'll stand up to the hot water from a pressure washer when cleaning your facility at the end of the day.
Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place. For high-speed applications, consider clamp-on shaft mounts, which are less likely to slip.
Clamp-On Shaft Mount—The clamp tightens around the shaft for a strong 360° grip. These mounts attach more securely than set screws to reduce vibration. Plus, there aren't any screws pressing into the shaft, so it stays free from damage. Also known as a concentric lock.
Corrosion-Resistant Nickel-Plated Steel—These bearings resist mild chemicals, such as the ammonia in cleaning solutions, while maintaining the strength of steel. The nickel coating can wear or chip over time, though. If it does, the steel beneath will rust quickly.
Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
Retaining Ring | Temp. Range, ° F | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | OD | Thk. | Bearing Seal Type | ABEC Rating | Dynamic Radial Load Cap., lb. | Max. Rotation Speed, rpm | Min. | Max. | Enclosure Rating | Food Industry Std. | Each | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Set-Screw Shaft Mount | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Corrosion-Resistant Nickel-Plated Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1" | 2 3/64" | 3/4" | 2.266" | 0.047" | Sealed | 1 | 2,800 | 2,700 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 0000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/4" | 2 7/16" | 7/8" | 2.656" | 0.063" | Sealed | 1 | 4,350 | 2,000 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 3/8" | 2 55/64" | 15/16" | 3.078" | 0.063" | Sealed | 1 | 5,750 | 2,000 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 7/16" | 2 27/32" | 15/16" | 3.078" | 0.063" | Sealed | 1 | 5,750 | 2,000 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/2" | 3 5/32" | 1 3/32" | 3.406" | 0.063" | Sealed | 1 | 7,300 | 1,750 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 3/4" | 3 11/32" | 1 3/32" | 3.594" | 0.063" | Sealed | 1 | 7,900 | 1,600 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2" | 3 15/16" | 1 3/16" | 4.188" | 0.094" | Sealed | 1 | 9,750 | 1,350 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2 3/16" | 3 15/16" | 1 3/16" | 4.188" | 0.094" | Sealed | 1 | 9,750 | 1,350 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Clamp-On Shaft Mount | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Corrosion-Resistant Nickel-Plated Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/4" | 1 27/32" | 5/8" | 2.063" | 0.047" | Sealed | 1 | 2,600 | 3,100 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1" | 2 3/64" | 3/4" | 2.266" | 0.047" | Sealed | 1 | 2,800 | 2,700 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 3/16" | 2 7/16" | 7/8" | 2.656" | 0.063" | Sealed | 1 | 4,350 | 2,300 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/4" | 2 27/32" | 15/16" | 3.078" | 0.063" | Sealed | 1 | 5,750 | 2,000 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
25 mm | 52 mm | 19.1 mm | 57.5 mm | 1.2 mm | Sealed | 1 | 2,800 | 2,700 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
35 mm | 72 mm | 23.8 mm | 78.2 mm | 1.6 mm | Sealed | 1 | 5,750 | 2,000 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
40 mm | 80 mm | 27.8 mm | 86.5 mm | 1.6 mm | Sealed | 1 | 7,300 | 1,750 | -20 | 220 | IP69K | NSF Registered H1 | 0000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Light Duty Ball Bearings with Retaining Ring
![]() |
Install these bearings by hand in the housings of rotating parts that don't require high speed or precision, such as the shafts in hand cranks and casters. The ring stops the bearing from being jostled out of place when it experiences sudden forces parallel to the shaft (thrust loads).
Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
Extended Inner Ring—Connect to mating parts without the need for a spacer. The inner ring juts out farther than the outer ring, so shaft collars and other objects won't touch the bearing's moving parts.
Retaining Ring | Temp. Range, ° F | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | OD | Thk. | ABEC Rating | Dynamic Radial Load Cap., lb. | Max. Rotation Speed, rpm | Min. | Max. | Inner Ring Type | Bearing Trade No. | Each | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Sealed | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1/2" | 1 3/4" | 5/8" | 1.922" | 0.042" | Not Rated | 2,550 | 5,000 | -20 | 250 | Extended | 7508-2RS | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5/8" | 1 3/4" | 5/8" | 1.922" | 0.042" | Not Rated | 2,550 | 5,000 | -20 | 250 | Extended | 7510-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
3/4" | 1 3/4" | 5/8" | 1.922" | 0.042" | Not Rated | 2,550 | 5,000 | -20 | 250 | Extended | 7512-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1" | 2" | 5/8" | 2.156" | 0.042" | Not Rated | 2,950 | 5,000 | -20 | 250 | Extended | 7516-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/4" | 2 9/16" | 3/4" | 2.766" | 0.065" | Not Rated | 5,350 | 5,000 | -20 | 250 | Extended | 7520-2RS | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Hex-Bore Ball Bearings
![]() |
No need for set screws—the inside corners of these bearings hold them in place on hex shafts as they rotate. They're a good choice when your setup needs to come apart frequently, since there aren't extra mounting steps.
Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
Extended Inner Ring—Connect to mating parts without the need for a spacer. The inner ring juts out farther than the outer ring, so shaft collars and other objects won't touch the bearing's moving parts.
ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
Temp. Range, ° F | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Wd. | For Housing ID | Wd. | ABEC Rating | Dynamic Radial Load Cap., lb. | Max. Rotation Speed, rpm | Min. | Max. | Inner Ring Type | Bearing Trade No. | Each | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Sealed | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
11/16" | 1 27/32" | 35/64" | 1 | 2,850 | 6,000 | -40 | 250 | Extended | HPC011GP | 000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
7/8" | 2 3/64" | 19/32" | 1 | 3,150 | 5,900 | -40 | 250 | Extended | HPC014GP | 000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1" | 2 7/16" | 5/8" | 1 | 4,400 | 4,800 | -40 | 250 | Extended | HPC100GP | 000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/8" | 2 53/64" | 43/64" | 1 | 5,800 | 4,000 | -40 | 250 | Extended | HPS102GP | 000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1 1/2" | 3 11/32" | 3/4" | 1 | 7,300 | 3,500 | -40 | 250 | Extended | HPS108GR | 000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Square-Bore Ball Bearings
![]() |
The inside corners of these bearings grip square shafts as they turn, so you don't need set screws to hold them in place. They're a good choice when your setup needs to come apart frequently, since there aren't extra mounting steps.
Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
Extended Inner Ring—Connect to mating parts without the need for a spacer. The inner ring juts out farther than the outer ring, so shaft collars and other objects won't touch the bearing's moving parts.
ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
Temp. Range, ° F | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Wd., mm | For Housing ID, mm | Wd., mm | ABEC Rating | Dynamic Radial Load Cap., lb. | Max. Rotation Speed, rpm | Min. | Max. | Inner Ring Type | Bearing Trade No. | Each | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Sealed | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
26 | 80 | 18 | 1 | 7,300 | 500 | -20 | 200 | Extended | W208PP6 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
29.5 | 80 | 18 | 1 | 7,300 | 500 | -20 | 200 | Extended | W208PP5 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
38.5 | 100 | 33.3 | 1 | 9,750 | 500 | -20 | 200 | Extended | GW211PP17 | 0000000 | 00000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
45 | 110 | 38.2 | 1 | 11,800 | 500 | -20 | 200 | Extended | GW212PP50 | 0000000 | 000000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||