Light diffuses evenly from the sides and bottom to produce ambient lighting. These fixtures are ideal for offices, storage rooms, and other indoor spaces.

Don’t waste energy lighting unoccupied spaces—these lights turn on when they detect movement.

Brighten entryways and small spaces.

Maximize the light that reaches your shelving. Often used in storage rooms and warehouse rack rows, these lights have reflectors that direct all light downwards from ceilings up to 24 ft. high.

Also known as troffers, these lights fit most standard drop-ceiling grids and are often used in offices, storage rooms, and other indoor spaces. Drop them into your recessed ceiling grid.

Install these lights into ceiling cutouts with housings for direct, overhead lighting. They’re often used in indoor spaces such as offices and lobbies, and as decorative lighting.

Brighten high-traffic areas with our most rugged ceiling lights. Rated IK10, the highest impact resistance rating, they’re protected by a 16-gauge cold-rolled steel frame and polycarbonate lens.

Powered by the sun, these lights illuminate outbuildings, shipping containers, and other remote places that lack electricity.

Rated for over a decade of use well above 100° F, these linear bay lights long outlast standard facility lights in high heat.

Create ambient and accent lighting with these sleek, modern lights that shine above, below, and around themselves.

Customize these lights to label doors or areas of a building.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust.

Illuminate areas that need frequent cleaning, such as food processing lines, with long rows of lights. Rated IP65, these lights have a sealed lens and liquid-tight end caps that protect them from low-pressure washdowns and dust.

Contain explosions, sparks, and flashes—the enclosure on these ceiling lights makes them safe to use in NEC Class I and II, Division 1 hazardous locations.

Brighten chemical plants, refineries, and other facilities where flammable and combustible gases, dust, or fibers may be present in the event of a leak or ventilation failure. These lights are rated for use in NEC Class I, II, and III, Division 2 hazardous locations.

Built for hot, hazardous areas such as steel mills and refineries, these lights work in temperatures up to 212° F. Rated NEC Classes I and II, they’re safe to use where there are ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.

Upgrade your existing hazardous location bay lights to energy-efficient LEDs.

Tough enough for offshore rigs and seafaring vessels—yet less than half the height of typical jelly jar lights. Built with a thick aluminum housing and a tough polycarbonate lens, these lights withstand hard impact without a guard.

To keep contaminants from entering your clean room, these lights seal against drop ceilings with an airtight gasket.

Guide pedestrians and drivers at night with lighting that defines paths and driveways. These lights produce ambient illumination without the glare of overhead lights.

Illuminate entryways and walkways at night—these lights shine when they detect motion. Powered by the sun, they can be installed where you don’t have access to electricity.

Light up offshore rigs, coal mines, and other outdoor areas where gas, vapor, or dust could ignite. These lights have an enclosure that contains sparks and explosions, so they won’t react with nearby hazards.

No need for wiring—these lights plug-in with a three-prong plug.

Hardwire these lights to a power source.

Hang these lights in garages and covered walkways to create a safe, well-lit path. They’re also known as canopy lights.

Also known as drip caps, these lights have a rounded housing that diverts rain and snow away from your doorframe. Mount them above entrances to light the way and keep water from trickling inside.

See what’s happening outside your facility—day and night. These lights have a built-in video camera that records when they sense motion.

Point these lights toward paths, doorways, and other dark areas. Since they run on batteries, you can skip the hassle of running wires.

When the power goes out, these lights turn on. They have adjustable heads that illuminate the path toward exits during outages.

Light the path toward exits where combustible gases and dust are constantly present—the enclosure on these lights contains sparks and flashes to prevent a reaction with nearby hazards. They’re often found in extreme environments, such as refineries and chemical plants.

Install these lights in aircraft hangars, gas plants, and other facilities where flammable and combustible gases or dust may be present, such as leaks or ventilation failures. Rated NEC Class I, Division 2, they seal out gases but aren't built to contain explosions.

Brighten loading docks and trailers—these lights swing out from the wall and tilt to direct light where it’s needed.

A sealed head and switch keep these lights shining in wet environments. They swing out from the wall and adjust horizontally and vertically to illuminate loading dock and trailers.