Brighten high-traffic areas with our most rugged ceiling lights. Rated IK10, the highest impact resistance rating, they’re protected by a 16-gauge cold-rolled steel frame and polycarbonate lens. A good choice for public spaces such as parking garages and stairwells, the lens is secured with tamper-resistant Torx screws to prevent vandalism. They have a center pin that makes them difficult to remove without special tools. The lens disperses light from the sides and bottom for ambient lighting.

Install these lights in covered areas indoors or outdoors—UL listed for wet locations, they’re sealed against humidity and dripping, splashing, and falling liquids.

Maximize the light that reaches your shelving. Often used in storage rooms and warehouse rack rows, these lights have reflectors that direct all light downwards from ceilings up to 24 ft. high. CSA certified for damp locations, they withstand humidity and moisture.

Neutral lights are often found in workspaces. Cool lights highlight white and blue tones. This is ideal where you need high visibility, such as inspection areas.

Add suspension hardware to hang lights from the ceiling. Includes two wire rope slings with hooks and two wire rope clamps. No tools required—adjust the length and tighten clamps to secure.

Add connectors to join multiple lights together in a straight line. Each joint between two lights requires two connectors.

Emergency backup batteries meet UL 924, which means they’ll power one light for up to 90 minutes if the power goes out. Install them inside the fixture housing. They include a manual test button which you mount on the underside of the light. They cannot be sold to California.

For technical drawings and 3-D models, click on a part number.

Often used in stairwells and hallways, these lights save energy by only turning on when they sense movement. Once movement stops, they’ll dim or turn off completely—choose your preference with the controls in front. You can also adjust the light duration and sensor range. These lights are DLC (DesignLight Consortium) listed, so they’ve been tested to confirm their energy efficiency.

Choose between a neutral or cool light appearance on the LED driver to match existing lights. To minimize glare, the frosted lens disperses light evenly. It’s also made of polycarbonate to resist impact.

All are UL listed to resist humidity and moisture, so they’ll work in damp locations. Lights with a backup battery shine a 1,000 lumen light for 90 minutes if the power goes out.

For technical drawings and 3-D models, click on a part number.

Illuminate steps to reduce the risk of tripping or falling, especially at night or in poorly lit areas. They mount flush with your wall or step, so they won’t get snagged or bumped. A glass lens protects the LEDs from dust and damage. UL listed for wet locations, these lights are sealed to keep out humidity as well as dripping and splashed liquids.

Mount these lights in a standard 1-gang outlet box (not included) with the included mounting bracket.

Install wall-mount lights alongside the step. Install step-mount lights on the riser of the step.

For technical drawings and 3-D models, click on a part number.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust. Install them anywhere that requires frequent cleaning, even an ISO Class 5 clean room. They also meet NSF/ANSI 2, so you can use them in food processing areas with splashing liquid. These lights won’t shatter and contaminate your area—they’re rated IK10, the highest rating for impact protection. And since they’re IC rated, you won’t risk a fire if you install them in direct contact with insulation.

Casting a neutral light dispersed by a frosted lens, these lights won’t cause glare on equipment. The lens is made of acrylic to resist scratching and yellowing.

Mount these lights flush with ceilings in wet locations—all are sealed to keep out humidity and dripping, splashing, and falling liquids. Unlike recessed can lights, which require a separate housing, these fit directly into a cutout in your ceiling and are held in place by springs. With built-in LEDs, these lights last longer, are more efficient, and generate less heat than other light technologies. Use the switch on the power supply to choose between warm, cool, or neutral light—no more mismatched lights. All have passed strict U.S. and Canadian safety standards.

For technical drawings and 3-D models, click on a part number.

Brighten your ISO Class 3 clean room with long rows of lights—you can wire these lights together at the ends. They have an airtight seal that keeps contaminants from entering your space.

Mount these lights to T-bar style ceilings with No. 14 tapping screws (not included). When wiring them together, use the optional connector (sold separately).

Neutral lights are often found in workspaces.

Cool lights highlight white and blue tones. This is ideal where you need high visibility, such as inspection areas.

Prevent contaminants from entering your ISO Class 3 clean room—these lights have an airtight seal. What makes them great for clean rooms also makes these lights ideal for food preparation and other spaces that require frequent washdowns. They’re rated NSF/ANSI 2 for direct contact with food. Rated IP65 and ETL listed for wet locations, they’re sealed against humidity and low-pressure washdowns. They have a cool light appearance that highlights white and blue tones to make your work more visible. A prismatic lens casts a wide beam and limits glare on your equipment.

To install, fasten with No. 14 tapping screws and seal with silicone (both not included).

For technical drawings and 3-D models, click on a part number.