3/8"-24 Fasteners | McMaster-Carr

Filter by

Thread Size

Length

Material

Stainless Steel

Threading

Partially Threaded

Threaded on Both Ends

Threaded on One End

Fastener Head Type

System of Measurement

Finish

Cadmium Yellow-Chromate Plated

Dry Film Lubricated

Phosphate Coated

Tin Zinc Plated

Zinc Flake Coated

Zinc Yellow-Chromate Plated

Thread Spacing

Thread Type

UN/UNF (SAE 45°)

Thread Direction

Right Hand and Left Hand

Fastener Strength Grade/Class

Drive Style

External 12-Point

External Square

Socket Head Profile

Specifications Met

Federal Specification

Tensile Strength

30,000 psi to 99,999 psi

100,000 psi or greater

Head Height

Nut Type

Tamper Resistant

With Sight Hole

Thread Fit

Metric Class 6g

Metric Class 6H

Unified Standard Class 1A

Unified Standard Class 2A

Unified Standard Class 2B

Unified Standard Class 3A

Unified Standard Class 3B

Thread Length

DFARS Specialty Metals

Export Control Classification Number (ECCN)

REACH

RoHS

Compliant with Exemptions

Head Diameter

Drive Size

Shoulder Length

How can we improve?

1,435 Products

Fastening and Joining

Hex Head Screws

Hex Head Screws

Used with nuts to create a stronger joint than flat and rounded screws

Socket Head Screws

Socket Head Screws

With a deeper drive than flat and rounded head screws, these withstand more torque for a tighter hold

Rounded Head Screws

Rounded Head Screws

Sit just above the surface for a low-profile finish and hold tighter than flat head screws

Flat Head Screws

Flat Head Screws

Fit in countersunk holes for a flush finish

12-Point Screws

12-Point Screws

12 contact points handle more torque than a hex head while a flange eliminates the need for a washer

Set Screws

Exert pressure at the tip to hold parts in place, unlike screws that hold material together with threads

Shoulder Screws

Shoulder Screws

Rotate parts around the cylinder under the head to guide and align them during installation

Hanger Bolts

Suspend pipe and other fixtures with wire or cable ties

T-Bolts

Turn by hand for easy fastening, use as a handle, or attach as a point for straps and clamps

Flange Nuts

The flange distributes pressure, so you don't need a washer

Hex Nuts

Handle most general fastening needs

Easy to tighten and loosen by hand for making frequent adjustments

Cap Nuts

Cover and protect threads while adding a finished look; also known as acorn nuts

Locknuts

Hold fasteners in place to prevent loosening from vibration

Coupling Nuts

Connect and extend threaded rods

Sealing Nuts

Prevent leaks and block out contaminants with a rubber seal

Socket Nuts

Install in recessed holes and tight spots where a wrench won’t fit; also known as Allen nuts

Square Nuts

Flat sides won’t spin in channels and square holes

Tamper-Resistant Nuts

Tamper-Resistant Nuts

Hard to detach without special tools to prevent unwanted removal

Threaded Inserts

Threaded Inserts

Create new threads or repair stripped threads

Weld Nuts

Weld to metal surfaces to add permanent threads

Rivet Nuts

Add threads to thin panels with access from only one side; also known as blind inserts

Rivet-Mount Nuts

Rivet-Mount Nuts

Add threads in hard-to-reach areas and materials that are too thin to be tapped

Press-Fit Nuts

Push into drilled or punched holes to add threads to thin panels

Push Nuts

Press onto threads for a light duty hold that’s faster to install than typical nuts

Thread Adapters

Thread Adapters

Join threads of a different type, size, and gender

Single-End Studs

Single-End Studs

Use the unthreaded end as a pivot point, hinge, shaft, or locator pin

Threaded Rods

Anchor, connect, or hang components in a wide variety of applications

Taper Pins

Fit snugly into tapered holes to secure, position, and align components

Rivet Nut Tools

Rivet Nut Tools

Install rivet nuts

Power Transmission

Connecting Rods

Connecting Rods

Use with rod ends and swivel joints to link components in push/pull assemblies

Building and Machinery Hardware

Knobs

Position, tighten, and secure fixtures and equipment

Handle Nuts

Attach to threaded shafts to quickly turn the shafts by hand

Fabricating and Machining

Lathe Tool Insert Holder Replacement Parts

Lathe Tool Insert Holder Replacement Parts

Replace clamps, screws, shims, and other parts in lathe tool insert holders

Drill Bushings

Fit in holes to guide drill bits and other cutting tools for precise and repeatable holes and cuts

Fluid Handling

Tube and Tube Fittings

Tube and Tube Fittings

Typically more flexible than pipe for carrying liquids and gases in short runs around equipment

Hose Crimpers

Crimp ferrules onto hose to secure fittings

Hose and Hose Fittings

Hose and Hose Fittings

Flexible and stronger than tubing; often used to convey liquids and gases under pressure

Material Handling

Eyebolts

Route rope through the loop or attach hooks and shackles for lifting

Turnbuckles

Twist the body or end fittings to adjust the length and tension of attached rope and chain

The quick brown fox jumped over the lazy dog. Pedestal (35" Ht. x 4" Wd. x 4" Dp.)