Fixed Temperature Switches

Filter by

Switch Designation

Actuation Direction

Maximum Switching Current @ Voltage

Wire Connection

Maximum Temperature

Switch Starting Position

Environment

Number of Circuits Controlled

Maximum Housing Temperature

Measurement Unit

Electrical Connection

Voltage

Approximate Difference Between Set Point and Reset Point

Differential Range Sensitivity

Probe Diameter

Maximum Pressure

RoHS

U.S.–Mexico–Canada Agreement (USMCA) Qualifying

Yes

Export Control Classification Number (ECCN)

EAR99

DFARS Specialty Metals

REACH

Switch Type

Material

Number of Actuation Points

Enclosure Rating

Application

96 Products

Fixed-Setpoint Threaded Temperature Switches

Set to actuate at a specific temperature, these switches are easy to setup and prevent changes to the setpoint. They have a threaded probe, so they install directly into tanks, pipelines, and other process components to turn equipment on and off at a set temperature. All switches are NEMA 4 and 13 rated to seal out dirt, oil, and water from washdowns.

Narrow Differential Range Sensitivity—Narrow differential switches reset after a small temperature change in the opposite direction of your switch's actuation. For example, in a rising-actuation switch, they reset after the temperature falls 3° below the setpoint. Use them in systems where temperature changes slowly and where you need precision.

Wide Differential Range Sensitivity—Wide differential switches reset after the temperature significantly decreases (approximately 15%) below the setpoint. Use them in systems that cannot handle frequent power cycling.

Rising Actuation—Rising actuation switches activate when the temperature rises to the setpoint and then reset when the temperature falls below the setpoint. Choose rising actuation SPST-NO switches to power a cooler or trigger an alarm. Choose rising actuation SPST-NC switches to turn off a heater or other equipment when the temperature rises to the setpoint.

Falling Actuation—Falling actuation switches activate when the temperature falls to the setpoint and then reset when the temperature rises above the setpoint. Choose falling actuation SPST-NO switches to power a heater or activate an alarm. Choose falling actuation SPST-NC switches to turn off a cooler or other equipment when the temperature falls to the setpoint.

IP67 Enclosure Rating—IP67 rated switches stand up to temporary submersion.

UL Recognized Component—UL and C-UL listed switches meet U.S. and Canadian safety standards.

								Probe					SPST-NO		SPST-NC
	Actuation Point, ° F	Temp. Accuracy	No. of Actuation Points	Actuation Tolerance, ° F	No. of Circuits Controlled	Approx. Difference Between Set Point and Reset Point, ° F	Max. Switching Current @ Voltage (Electrical Phase)	Dia.	Lg.	Max. Pressure, psi	Enclosure Rating	Certification		Each		Each
Threaded Brass Probe—1/2 NPT Male







				Narrow Differential Range Sensitivity—Rising Actuation

				40	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N11	000000	4692N26	000000


				60	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N12	00000	4692N27	00000
				80	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N13	00000	4692N28	00000
				100	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N14	00000	4692N29	00000
				120	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N15	00000	4692N31	00000
				140	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N16	00000	4692N32	00000
				160	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N17	00000	4692N33	00000
				180	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N18	00000	4692N34	00000
				200	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N19	00000	4692N35	00000
				220	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N21	00000	4692N36	00000
				240	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N22	00000	4692N37	00000


				260	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N23	00000	4692N38	00000
				280	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N24	00000	4692N39	00000
				300	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N25	00000	4692N41	00000




						Narrow Differential Range Sensitivity—Falling Actuation

						40	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N42	00000	4692N57	00000


						60	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N43	00000	4692N58	00000
						80	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N44	00000	4692N59	00000
						100	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N45	00000	4692N61	00000
						120	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N46	00000	4692N62	00000
						140	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N47	00000	4692N63	00000
						160	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N48	00000	4692N64	00000
						180	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N49	00000	4692N65	00000
						200	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N51	00000	4692N66	00000
						220	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N52	00000	4692N67	00000
						240	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N53	00000	4692N68	00000


						260	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N54	00000	4692N69	00000
						280	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N55	00000	4692N71	00000
						300	±5° F	1	-5 to 5	1	3	6 amp @ 120V AC (Single) 4 amp @ 24V DC (Single)	3/8"	1/2"	5,000	NEMA 4, NEMA 13	UL Recognized Component, C-UL Recognized Component	4692N56	00000	4692N72	00000




								Wide Differential Range Sensitivity—Rising Actuation

								50	±7° F	1	-7 to 7	1	8	15 amp @ 125V AC (Single) 10 amp @ 250V AC (Single)	11/16"	1/2"	1,000	IP67, NEMA 4, NEMA 13	—	4692N73	00000	4692N84	00000


								75	±7° F	1	-7 to 7	1	12	15 amp @ 125V AC (Single) 10 amp @ 250V AC (Single)	11/16"	1/2"	1,000	IP67, NEMA 4, NEMA 13	—	4692N74	00000	4692N85	00000
								100	±7° F	1	-7 to 7	1	15	15 amp @ 125V AC (Single) 10 amp @ 250V AC (Single)	11/16"	1/2"	1,000	IP67, NEMA 4, NEMA 13	—	4692N75	00000	4692N86	00000
								125	±7° F	1	-7 to 7	1	19	15 amp @ 125V AC (Single) 10 amp @ 250V AC (Single)	11/16"	1/2"	1,000	IP67, NEMA 4, NEMA 13	—	4692N76	00000	4692N87	00000
								150	±7° F	1	-7 to 7	1	23	15 amp @ 125V AC (Single) 10 amp @ 250V AC (Single)	11/16"	1/2"	1,000	IP67, NEMA 4, NEMA 13	—	4692N77	00000	4692N88	00000
175								±7° F	1	-7 to 7	1	27	15 amp @ 125V AC (Single) 10 amp @ 250V AC (Single)	11/16"	1/2"	1,000	IP67, NEMA 4, NEMA 13	—	4692N78	00000	4692N89	00000
200	±7° F							1	-7 to 7	1	30	15 amp @ 125V AC (Single) 10 amp @ 250V AC (Single)	11/16"	1/2"	1,000	IP67, NEMA 4, NEMA 13	—	4692N79	00000	4692N91	00000
225	±7° F							1	-7 to 7	1	34	15 amp @ 125V AC (Single) 10 amp @ 250V AC (Single)	11/16"	1/2"	1,000	IP67, NEMA 4, NEMA 13	—	4692N81	00000	4692N92	00000
250	±7° F							1	-7 to 7	1	38	15 amp @ 125V AC (Single) 10 amp @ 250V AC (Single)	11/16"	1/2"	1,000	IP67, NEMA 4, NEMA 13	—	4692N82	00000	4692N93	00000
275	±7° F							1	-7 to 7	1	42	15 amp @ 125V AC (Single) 10 amp @ 250V AC (Single)	11/16"	1/2"	1,000	IP67, NEMA 4, NEMA 13	—	4692N83	00000	4692N94	00000

Surface-Mount Temperature Switches

Often used to control heat cable output, these switches maintain your surface’s temperature by turning equipment on or off when they reach a set temperature. They actuate when the temperature rises to the setpoint and reset when the temperature falls below the reset point. Since they're SPDT (single pole, double throw) switches, they control one circuit and can either be wired to turn one device from on to off (normally closed) or from off to on (normally open). Wire them normally closed to power a heater—when the temperature rises to the setpoint, the heater will turn off until the temperature falls below the reset point. Or wire them normally open to turn on alarms or other devices when the temperature rises above the setpoint. Their setpoint isn’t adjustable, so they’re easy to set up and there’s no risk of unintentional changes.

CSA-US Certified—CSA-US certified switches meet American safety standards.

CSA Certified—CSA certified switches meet Canadian safety standards.

							Mounting Holes			SPDT
	Actuation Point, ° F	Actuation Tolerance, ° F	Approx. Difference Between Set Point and Reset Point, ° F	Max. Switching Current @ Voltage (Electrical Phase)	Ht.	Wd.	No. of	Dia.	Certification		Each
Fixed Rising Actuation Point



		47	-6 to 6	10	15 amp @ 240V AC (Single)	1 1/8"	2"	2	3/16"	CSA-US Certified, CSA Certified	4693N11	0000000


		60	-6 to 6	15	15 amp @ 240V AC (Single)	1 1/8"	2"	2	3/16"	CSA-US Certified, CSA Certified	4693N12	000000
		75	-6 to 6	15	15 amp @ 240V AC (Single)	1 1/8"	2"	2	3/16"	CSA-US Certified, CSA Certified	4693N13	000000
		105	-6 to 6	15	15 amp @ 240V AC (Single)	1 1/8"	2"	2	3/16"	CSA-US Certified, CSA Certified	4693N14	000000
		200	-6 to 6	15	15 amp @ 240V AC (Single)	1 1/8"	2"	2	3/16"	CSA-US Certified, CSA Certified	4693N16	000000

Enclosure Thermostats

Fixed Thermostat

Control a single heating or cooling device in your enclosure to keep electronics at a safe operating temperature. Clip them on to a DIN rail and connect them to your heater, fan, or air conditioner. All these thermostats meet American, Canadian, or European safety standards.

Cooling—Cooling thermostats are normally open, so they’ll switch your fan or air conditioner on when the air in your enclosure reaches the temperature setting.

Heating—Heating thermostats are normally closed—when the air in your enclosure reaches the temperature setting, the thermostat will turn the heater off.

Fixed Actuation Point—Fixed thermostats have a fixed temperature setting to prevent tampering or accidental changes.

IP20 Enclosure Rating—They have an IP20 rating—to prevent shocks, fingers won’t fit inside.

UL 94 V-0—They also meet UL 94 V-0, so they self-extinguish within 10 seconds if they catch fire and won’t spread the fire by dripping.

Temperature Setting—These thermostats keep the air in your enclosure within a set range. Temperature setting is the high end of the range for both heating and cooling thermostats.

Temperature Difference—Temperature difference is the difference between the temperature when the thermostat turns your device on and when it turns off. For a heater thermostat with a temperature setting of 50° and an 18° temperature difference, the thermostat will switch your heater on when the temperature goes below 32° and off once the temperature reaches 50°. Thermostats with a lower temperature difference maintain a narrower range of temperatures, but they use more power because they switch on and off more frequently.

	Temp.						Overall
	Setting	Difference	Tolerance	Voltage	Current, amp	For DIN Rail Ht., mm	Ht.	Wd.	Dp.	Enclosure Rating	Flammability Rating	Certification		Each
Cooling







				Fixed Actuation Point

				95° F, 35° C	18° F, 10° C	-11° F to 11° F/-6° C to 6° C	120V AC, 240V AC, 24V DC to 75V DC	16	35	1 7/8"	1 5/16"	1 5/16"	IP20	UL 94 V-0	C-UL Recognized Component, CE Marked, UL Recognized Component, VDE Certified	3941N21	000000


				122° F, 50° C	18° F, 10° C	-11° F to 11° F/-6° C to 6° C	120V AC, 240V AC, 24V DC to 75V DC	16	35	1 7/8"	1 5/16"	1 5/16"	IP20	UL 94 V-0	C-UL Recognized Component, CE Marked, UL Recognized Component, VDE Certified	3941N18	00000
				140° F, 60° C	18° F, 10° C	-12.6° F to 12.6° F/-7° C to 7° C	120V AC, 240V AC, 24V DC to 75V DC	16	35	1 7/8"	1 5/16"	1 5/16"	IP20	UL 94 V-0	C-UL Recognized Component, CE Marked, UL Recognized Component, VDE Certified	3941N19	00000


				Heating







								Fixed Actuation Point

								50° F, 10° C	18° F, 10° C	-9° F to 9° F/-5° C to 5° C	120V AC, 240V AC, 24V DC to 75V DC	16	35	1 7/8"	1 5/16"	1 5/16"	IP20	UL 94 V-0	C-UL Recognized Component, CE Marked, UL Recognized Component, VDE Certified	3941N17	00000


								59° F, 15° C	18° F, 10° C	-9° F to 9° F/-5° C to 5° C	120V AC, 240V AC, 24V DC to 75V DC	16	35	1 7/8"	1 5/16"	1 5/16"	IP20	UL 94 V-0	C-UL Recognized Component, CE Marked, UL Recognized Component, VDE Certified	3941N15	00000
								77° F, 25° C	18° F, 10° C	-9° F to 9° F/-5° C to 5° C	120V AC, 240V AC, 24V DC to 75V DC	16	35	1 7/8"	1 5/16"	1 5/16"	IP20	UL 94 V-0	C-UL Recognized Component, CE Marked, UL Recognized Component, VDE Certified	3941N16	00000

Enclosure Thermostats for Multiple Devices

Keep electronics in your enclosure from getting too hot or cold with these thermostats that control two devices at once. Clip them to a DIN rail to install.

For Heating and Cooling Thermostats with Two Actuation Points

Fixed Thermostat

Cooling thermostats regulate two cooling devices, such as a fan and an air conditioner, for two-stage cooling. Use only one device for cooling in mild temperatures or both for extreme heat. These thermostats switch your equipment on when the enclosure is hotter than the temperature setting. Once the temperature is reduced by the temperature difference, it will switch off. For example, a thermostat set at 77° F for a fan and 140° F for an air conditioner will power both devices when the enclosure is over 140° F. With a temperature difference of 18° F, the air conditioner will switch off when the temperature goes below 122° F. The fan will run until the temperature reaches 59° F, and switch back on if it heats up to 77° F or hotter.

Heating and cooling thermostats control heaters and fans or air conditioners.

Heating and cooling thermostats with two actuation points control two devices independently. When your enclosure temperature is within the set range, neither device is powered, so they’re more efficient than changeover thermostats. For each device, temperature setting is the high end of the temperature range, and temperature difference is the size of the range. For a thermostat with temperature settings of 59° and 95° F and an 18° F temperature difference, the heater will switch on when your enclosure is colder than 41° F and turn off when it reaches 59° F. The fan or other cooling device will switch on when the temperature goes above 95° F and turn off once the enclosure cools to 77° F.

Fixed Actuation Point—Fixed thermostats prevent tampering and accidental changes.

IP20 Enclosure Rating—All thermostats meet IP20, which means they’re designed so fingers can’t fit inside and get shocked.

UL 94 V-0—They also meet UL 94 V-0, so they self-extinguish within 10 seconds if they catch fire and won’t spread the fire by dripping.

Certification—Thermostats that are CE marked or VDE certified meet European safety standards. UL Recognized Component and C-UL Recognized Component thermostats also meet American and Canadian safety standards.

	Heating Temperature			Cooling Temperature				Overall
	Setting	Difference	Tolerance	Setting	Difference	Tolerance	Voltage	Ht.	Wd.	Dp.	Enclosure Rating	Flammability Rating	Certification		Each
Fixed Actuation Point



		59° F, 15° C	18° F, 10° C	-9° F to 9° F, -5° C to 5° C	95° F, 35° C	18° F, 10° C	-12.6° F to 12.6° F, -7° C to 7° C	120V AC, 240V AC, 24V DC to 75V DC	1 7/8"	2 1/2"	1 5/16"	IP20	UL 94 V-0	C-UL Recognized Component, CE Marked, UL Recognized Component, VDE Certified	6967N16	000000


		59° F, 15° C	18° F, 10° C	-9° F to 9° F, -5° C to 5° C	122° F, 50° C	18° F, 10° C	-12.6° F to 12.6° F, -7° C to 7° C	120V AC, 240V AC, 24V DC to 75V DC	1 7/8"	2 1/2"	1 5/16"	IP20	UL 94 V-0	C-UL Recognized Component, CE Marked, UL Recognized Component, VDE Certified	6967N14	00000
		77° F, 25° C	18° F, 10° C	-9° F to 9° F, -5° C to 5° C	122° F, 50° C	18° F, 10° C	-12.6° F to 12.6° F, -7° C to 7° C	120V AC, 240V AC, 24V DC to 75V DC	1 7/8"	2 1/2"	1 5/16"	IP20	UL 94 V-0	C-UL Recognized Component, CE Marked, UL Recognized Component, VDE Certified	6967N17	00000

For Cooling Thermostats with Two Actuation Points

Fixed Thermostat

Fixed Actuation Point—Fixed thermostats prevent tampering and accidental changes.

IP20 Enclosure Rating—All thermostats meet IP20, which means they’re designed so fingers can’t fit inside and get shocked.

UL 94 V-0—They also meet UL 94 V-0, so they self-extinguish within 10 seconds if they catch fire and won’t spread the fire by dripping.

	Cooling Temperature			Cooling Temperature Second Actuation Point				Overall
	Setting	Difference	Tolerance	Setting	Difference	Tolerance	Voltage	Ht.	Wd.	Dp.	Enclosure Rating	Flammability Rating	Certification		Each
Fixed Actuation Point



		122° F, 50° C	18° F, 10° C	-12.6° F to 12.6° F, -7° C to 7° C	140° F, 60° C	18° F, 10° C	-12.6° F to 12.6° F, -7° C to 7° C	120V AC, 240V AC, 24V DC to 75V DC	1 7/8"	2 1/2"	1 5/16"	IP20	UL 94 V-0	C-UL Recognized Component, CE Marked, UL Recognized Component, VDE Certified	6967N18	000000

Harsh Environment Surface-Mount Temperature Switches

An airtight seal on these switches blocks out dust, dirt and moisture. They maintain your surface’s temperature by turning equipment on or off when they reach a set temperature. These switches actuate when the temperature rises to the setpoint and reset when the temperature falls below the reset point. Since they're SPDT (single pole, double throw) switches, they control one circuit and can either be wired to turn one device from on to off (normally closed) or from off to on (normally open). Wire them normally closed to power a heater—when the temperature rises to the setpoint, the heater will turn off until the temperature falls below the reset point. Or wire them normally open to turn on alarms or other devices when the temperature rises above the setpoint. Their setpoint isn’t adjustable, so they’re easy to set up and there’s no risk of unintentional changes.

CSA-US Certified—CSA-US certified switches meet American safety standards.

CSA Certified—CSA certified switches meet Canadian safety standards.

									Mounting Holes			SPDT
Actuation Point, ° F	No. of Actuation Points	Actuation Tolerance, ° F	No. of Circuits Controlled	Approx. Difference Between Set Point and Reset Point, ° F	Max. Switching Current @ Voltage (Electrical Phase)	Max. Pressure	Ht.	Wd.	No. of	Dia.	Certification		Each







			Fixed Rising Actuation Point

			47	1	-6 to 6	1	10	15 amp @ 240V AC (Single)	Not Rated	2 15/16"	2"	2	11/64"	CSA-US Certified, CSA Certified	3599K311	0000000


			60	1	-6 to 6	1	15	15 amp @ 240V AC (Single)	Not Rated	2 15/16"	2"	2	11/64"	CSA-US Certified, CSA Certified	3599K312	000000
			75	1	-6 to 6	1	15	15 amp @ 240V AC (Single)	Not Rated	2 15/16"	2"	2	11/64"	CSA-US Certified, CSA Certified	3599K313	000000
			105	1	-6 to 6	1	15	15 amp @ 240V AC (Single)	Not Rated	2 15/16"	2"	2	11/64"	CSA-US Certified, CSA Certified	3599K314	000000
			200	1	-6 to 6	1	15	15 amp @ 240V AC (Single)	Not Rated	2 15/16"	2"	2	11/64"	CSA-US Certified, CSA Certified	3599K315	000000