This self-extinguishing tubing meets UL 94 V-0 and UL 94 V-1 for flame retardance, so it delays the spread of flames to valuable equipment.

This self-extinguishing tubing meets UL 94 V-0 or UL 94 V-2 for flame retardance to delay the spread of flames to valuable equipment.

Run chemicals through this tubing at temperatures between -100° F and 500° F.

This durable tubing has the best abrasion and wear resistance of all our hard tubing for chemicals.

The industry standard for general purpose food, beverage, and dairy applications, this tubing meets NSF/ANSI Standard 51 for food contact.

Designed for high-purity applications, this hard tubing is cleaned and bagged to prevent dirt and moisture from contaminating the inside. It is free of plasticizers like DEHP, so it won’t impart tastes or odors to the fluid running through it.

Use this pipe in gravity-flow applications that involve highly-corrosive chemicals–it is NSF certified for use in corrosive waste systems. Pipe is made of CPVC, which has better chemical resistance than ABS plastic to stand up to acids and other harsh substances.

With the smallest bend radius of all the fume hose we offer, this lightweight hose can handle tight turns around equipment.

Hose has a single thin layer of PVC-coated fiberglass for venting smoke, water-based paint fumes, and welding fumes.

Not only does this hose stand up to corrosive fumes, it has a metal spiral on the outside that acts as a wear strip to protect against damage.

The neoprene coating on this hose withstands continuous motion without weakening.

The neoprene coating on this hose holds up under high heat.

This general purpose hose for blowing and vacuum applications has a thick PVC wear strip that protects against damage caused by dragging.

The small bend radius makes this hose easy to wrap around corners and install in tight spaces.

The ends of this hose have a belt-and-buckle connection that eliminates the need for clamps.

Our most versatile duct hose for blowing and venting air, this polyester hose is lightweight and very flexible.

This extruded acrylic offers similar performance as cast acrylic at a lower cost.

The addition of PTFE provides a more slippery, wear-resistant surface than standard Delrin® acetal resin. It’s commonly fabricated into pump components, gears, and bearings.

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.

CPVC is just as chemical resistant as standard PVC Type 1 and can handle hotter temperatures up to 200° F.

Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.

Made of PVC, this sleeving resists chemicals, oil, and acids.

Add a layer of insulation to prevent electricity and heat from dissipating from wire and cable.

Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

Made of PTFE, this sleeving has excellent resistance to chemicals and acids. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Coated with PVC, this polyester sleeving resists chemicals and solvents. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Use this shielded sleeving to protect wire and cable from signal distortion caused by nearby equipment and devices. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

Attach conduit to a knockout in an outlet box or enclosure.

Join pieces of conduit.

Thicker corrugations make this conduit more crush resistant than standard flexible plastic conduit.

With excellent resistance to tears and cuts, this tubing withstands demanding use.

Often used to bundle batteries, capacitors, and other electronics, this tubing tightly conforms to objects, similar to shrink wrap. It has excellent resistance to chemicals, oil, and acids.

A flame-retardant additive makes this polyolefin tubing combustion resistant and minimizes the spread of flames.

Often used in automated applications such as robotics, this highly flexible silicone rubber tubing withstands continuous motion without cracking and tearing. It resists abrasion and can be dragged over rough surfaces without damage.

A spring extension prevents sharp bends and kinks in your cord, prolonging its life. These bushings, which are more rigid than grommets, shield cords from rubbing against the edges of holes in enclosures and panels, so they won’t wear down.

Use Garolite G-10 in place of Garolite G-10/FR4 for applications that are sensitive to halogen, such as in nuclear plants. It's strong, machinable, and electrically insulating.

Hard fiber is the easiest composite to machine, making it good for creating custom parts. Also known as vulcanized fiber.