How to Identify and Measure Fittings
Pipe size is an industry designation, not the actual size. View information about how to measure threaded and unthreaded pipe and pipe fittings.
More
Fiberglass Pipe Flanges for Corrosive Chemicals
- For Use With: Acetic Acid (75%), Alcohol, Calcium Chloride, Chlorine, Fuel Oil, Gasoline, Hydrochloric Acid (37%), Nitric Acid (10%), Oil, Phosphoric Acid, Salt Water (30%), Sodium Hydroxide (50%), Solvents, Sulfuric Acid (70%), Water
- Temperature Range: 32° to 200° F
- Specifications Met: ASTM D4024
Flanges have excellent corrosion resistance to handle a wide range of acids and other highly-corrosive chemicals. Use in metal surface treating applications, plating solution lines, and other chemical process applications. They are reinforced with fiberglass layers for better strength and durability than any of our other pipe flanges for chemicals. Bolt two same-size flanges together with a gasket (sold separately) to create an access point within a line. Flanges meet ASTM D4024 specifications and testing requirements for product dimensions, performance, and material quality.
To connect flanges to pipe, first sand the inside of the flange and the end of the pipe to remove the surface finish. Next, mix the adhesive (sold separately) until the color is uniform with no streaks. Apply a thin layer of mixed adhesive to the sanded area of the pipe, approximately 1/8” thick. Repeat this process with the inside of the flange, applying a layer approximately 1/16” thick. After sealant has been applied, push the flange onto the pipe until it is fully engaged. Make sure you align the bolt holes prior to installing to minimize rotation after the flange is installed. Finally, use the adhesive-curing heat cable (sold separately) to cure the adhesive. Wrap the tape around the pipe and flange at the joint, taking care to not overlap the tape. Once you have waited the full cure time, the pipe and flange will be ready to use.
Warning: Never use plastic pipe flanges and pipe with compressed air or gas.
| Pipe Size  | Socket Dp. | Flange OD | For Bolt Dia. | Bolt Hole Dia. | Number of Bolt Holes | Bolt Circle Dia. | Material | Color | Max. Pressure | Each | |
| 1 1/2 | 1 3/8" | 5" | 1/2" | 5/8" | 4 | 3 7/8" | Fiberglass | Black | 300 psi @ 72° F | 0000000 | 0000000 |
| 2 | 1 3/4" | 6" | 5/8" | 3/4" | 4 | 4 3/4" | Fiberglass | Black | 250 psi @ 72° F | 0000000 | 000000 |
| 3 | 2" | 7 1/2" | 5/8" | 3/4" | 4 | 6" | Fiberglass | Black | 250 psi @ 72° F | 0000000 | 000000 |
| 4 | 2 1/2" | 9" | 5/8" | 3/4" | 8 | 7 1/2" | Fiberglass | Black | 150 psi @ 72° F | 0000000 | 000000 |
| Pipe Cement (11.8-fl. oz. Can) | 0000000 | Each | 000000 |
Cap flanges are also known as blind flanges.
| Pipe Size | Flange OD | For Bolt Dia. | Bolt Hole Dia. | Number of Bolt Holes | Bolt Circle Dia. | Material | Color | Max. Pressure | Each | |
| 1 1/2 | 5" | 1/2" | 5/8" | 4 | 3 7/8" | Fiberglass | Black | 300 psi @ 72° F | 0000000 | 0000000 |
| 2 | 6" | 5/8" | 3/4" | 4 | 4 3/4" | Fiberglass | Black | 250 psi @ 72° F | 0000000 | 000000 |
| 3 | 7 1/2" | 5/8" | 3/4" | 4 | 6" | Fiberglass | Black | 250 psi @ 72° F | 0000000 | 000000 |
| 4 | 9" | 5/8" | 3/4" | 8 | 7 1/2" | Fiberglass | Black | 150 psi @ 72° F | 0000000 | 000000 |
| Pipe Cement (11.8-fl. oz. Can) | 0000000 | Each | 000000 |
| Voltage | Max. Heat Output, °F | Lg. | Wd. | Thick. | Plug Type | Cord Lg. | Each | |
| 120V AC | 270° | 6 ft. | 1" | 1/8" | Two Prong | 6 ft. | 0000000 | 0000000 |
Yor-Lok Fittings for Stainless Steel Tubing
A nut with two sleeves (ferrules) gives these fittings extra gripping power. The sleeves bite into tubing as you tighten the nut, creating a strong seal. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and A-Lok fittings.
316 stainless steel fittings have excellent corrosion resistance.
- For Use With: Air, Cutting Oil, Fuel Oil, Gasoline, Hydraulic Fluid, Mineral Oil, Natural Gas, Steam, Water
- Tubing: Use with welded or seamless 304/304L or 316/316L stainless steel that meets ASTM A213, ASTM A249, or ASTM A269
Fittings with flange end connect to another same-size flange with a gasket (sold separately) to create an access point in your line. They are also known as Pressure Class 150 flanges.
For Tube | Bolt Hole | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Wall Thick. | Pipe Size | Flange OD | Material | Max. Pressure | Temp. Range, °F | Bolt Circle Dia. | Dia. | No. of | Bolts Included | Specifications Met | Each | |
| 1/2" | 0.035" | 1/2 | 3 1/2" | 316 Stainless Steel | 250 psi @ 72° F | -420° to 1200° | 2 3/8" | 5/8" | 4 | No | ASME B16.5 | 00000000 | 0000000 |
| 1/2" | 0.035" | 1 | 4 1/4" | 316 Stainless Steel | 250 psi @ 72° F | -420° to 1200° | 3 1/8" | 5/8" | 4 | No | ASME B16.5 | 00000000 | 000000 |
Use these nuts with Yor-Lok sleeves and fittings to create an extra-strong seal on stainless steel tubing. They are 316 stainless steel for excellent corrosion resistance.
For Tube | ||||||
|---|---|---|---|---|---|---|
| OD | Wall Thick. | Nut Material | Max. Pressure | Temp. Range, °F | Each | |
| 1/2" | 0.035" | 316 Stainless Steel | 2,000 psi @ 72° F | -420° to 1200° | 00000000 | 000000 |
Couple these sleeves with Yor-Lok nuts and fittings to create an extra-strong seal on stainless steel tubing. Sleeves are 316 stainless steel for excellent corrosion resistance. They are also known as ferrules.
Save time installing sleeves and nuts—these sets come oriented in the correct direction and order on a dispenser. To install them, slide off a set and place it on your tubing. Each front sleeve, back sleeve, and nut is made of 316 stainless steel for excellent corrosion resistance. Five sets of sleeves and nuts come on each dispenser. Sleeves are also known as ferrules.
For Tube | Front Sleeve | Back Sleeve | Nut | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Wall Thick. | Material | Lg. | No. Included | Lg. | No. Included | Lg. | No. Included | Max. Pressure | Each | |
Sets with Dispenser | |||||||||||
| 1/2" | 0.035" | 316 Stainless Steel | 9/32" | 5 | 5/32" | 5 | 11/16" | 5 | 2,000 psi @ 72° F | 0000000 | 000000 |
PTFE sleeves are plastic instead of stainless steel, so they won’t damage tubing.
| For Tube OD | Sleeve Material | Max. Pressure | Temp. Range, °F | Each | |
| 1/2" | PTFE Plastic | Not Rated | -65° to 350° | 00000000 | 00000 |
Tube supports are recommended for soft plastic tubing to prevent the tube from collapsing.
For Tube | ||||||
|---|---|---|---|---|---|---|
| OD | ID | Tube Support Material | Tube Support Style | Temp. Range, °F | Each | |
| 1/2" | 1/4" | 316 Stainless Steel | Smooth | -420° to 1200° | 00000000 | 000000 |
Minimal-Spill Push-and-Turn Hose Couplings for Chemicals
Quickly connect and disconnect hose lines used with a variety of chemicals, from adhesives to isopropyl alcohol and ink. Any part of these couplings that contacts fluid is made from 316 stainless steel, C-276 Hastelloy, PTFE, or fluoroelastomer to withstand the chemicals in your line. Tough enough to handle frequent use, these couplings are designed to be virtually spill free. Also known as dry disconnects and double-shut off couplings, both the plug and the socket have a shut-off valve that stops the flow of liquids when they’re separated. To connect, push the plug into the socket and lock with a quarter turn. The socket swivels, so you won’t have to twist your hose to attach the plug. It also has a rubber lip and large handles to prevent damage if it’s dropped.
A complete coupling consists of a plug and a socket (both sold separately). They’re compatible with MannTek, Avery Hardoll, Todo-matic, and other dry-disconnect couplings that meet NATO standard STANAG 3756.
Aluminum couplings are lighter in weight than stainless steel and have good corrosion resistance.
316 stainless steel couplings have excellent corrosion resistance.
- For Use With:
Aluminum: Acetone, Adhesives, Benzene, Boric Acid, Butyl Alcohol, Diesel Fuel, Ethanol, Ethylene Glycol, Fuel Oil, Gasoline, Hydraulic Fluid, Ink, Isopropyl Alcohol, Mineral Oil, Mineral Spirits, Varnish, Vegetable Oil
316 Stainless Steel: Acetone, Adhesives, Benzene, Boric Acid, Butyl Alcohol, Citric Acid, Diesel Fuel, Ethanol, Ethylene Glycol, Fuel Oil, Gasoline, Hydraulic Fluid, Ink, Isopropyl Alcohol, Mineral Oil, Mineral Spirits, Nitric Acid, Sodium Hydroxide, Varnish, Vegetable Oil - Maximum Pressure:
Aluminum: 230 psi @ 72° F
316 Stainless Steel: 360 psi @ 72° F - Temperature Range: -15° to 400° F
Bolt Hole | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Plug OD | Pipe Size | Flange OD | Flanged Connection Surface | Pressure Class | For Bolt Dia. | Dia. | No. of | Bolt Circle Dia. | Each | |
Aluminum | ||||||||||
| 2 3/4" | 2 | 6" | Flat | 150 | 5/8" | 3/4" | 4 | 4 3/4" | 0000000 | 0000000 |
| 4 11/16" | 3 | 7 1/2" | Flat | 150 | 5/8" | 3/4" | 4 | 6" | 0000000 | 000000 |
316 Stainless Steel | ||||||||||
| 2 3/4" | 2 | 6" | Raised | 150 | 5/8" | 3/4" | 4 | 4 3/4" | 0000000 | 000000 |
| 4 11/16" | 3 | 7 1/2" | Raised | 150 | 5/8" | 3/4" | 4 | 6" | 0000000 | 00000000 |
- For Use With: Acetone, Adhesives, Benzene, Boric Acid, Butyl Alcohol, Citric Acid, Diesel Fuel, Ethanol, Ethylene Glycol, Fuel Oil, Gasoline, Hydraulic Fluid, Ink, Isopropyl Alcohol, Mineral Oil, Mineral Spirits, Nitric Acid, Sodium Hydroxide, Varnish, Vegetable Oil
- Maximum Pressure: 360 psi @ 72° F
- Temperature Range: -15° to 400° F