We will reply to your message within an hour.
These steel anchors are available with corrosion-resistant finishes.
More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.
These 18-8 stainless steel anchors have good chemical resistance.
Keep fixtures solidly in place—these anchors have two locking wedges that won't shake loose.
The removable flat head provides a flush finish in countersunk holes.
A zinc plating provides corrosion resistance in wet environments.
An open-end cap nut provides a finished appearance.
Drive these tools with a hammer until the thicker portion of the tool makes contact with the anchor, causing it to expand.
Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.
These 316 stainless steel anchors have excellent resistance to chemicals and salt water.
Also known as double expansion anchors, these expand from both sides for full contact and a secure hold.
An adjustable stop allows you to set anchors at consistent depths. Use with a hammer.
The fastest way to install shallow-hole female-threaded anchors. Just push the tip of the tool into the anchor and turn the tool with a power drill.
Often referred to as four-way expansion anchors, these expand in four directions to resist loosening from vibration.
Also known as caulk-in anchors, these stay secure when there's not much material to hold.
Drive these tools with a hammer to expand anchors.
Bolts are beveled under the head for a flush finish in countersunk holes.
A hex head allows for a secure grip with a wrench.
Turn the bolt to expand the nut for a secure hold in concrete. These anchors are often used to anchor machinery.
Use in applications requiring high strength.
Also known as drive rivets, install these anchors by hammering the pin into the body. Pry out the pin to remove.
These anchors are also known as drive rivets. To install, hammer the pin into the body. Pry out the pin to remove.
A tamper-resistant nut prevents unwanted removal of the object you are anchoring.
Also known as drive rivets, install by hammering the screw into the body. Unthread the screw to remove.
These anchors are also known as drive rivets. To install, hammer the screw into the body. Unthread the screw to remove.
Also known as tap-in or uni-tap rivets, these anchors are barbed to resist pull out. Made from nylon, they're chemical resistant.
Also known as lag shields, these anchors are designed for use with large-diameter wood screws.
Also known as mungo anchors, these have large fins that prevent rotation.
Use with any type of sheet metal or wood screw.
These stud-style anchors include a nut and a washer.
A pivoting toggle bar creates a strong hold.
For narrow holes and small cavities where toggle anchors won't fit.
Used with adhesive in bricks and hollow blocks, such as cinder blocks, these mesh tubes create a stronger hold for rods and studs than other anchors.
These stud anchors strengthen the parts of buildings where steel framing connects to concrete. They’re also known as Nelson studs.
18-8 stainless steel anchors have good chemical resistance.
High-strength toggle anchors provide an extremely strong hold and stay in position when a bolt is removed.
Bolts are beveled under the head for use in countersunk holes.
A shallow head makes these bolts good for low-clearance applications.
A spring-loaded toggle holds against the back of the material.
These anchors fit a range of sheet metal and wood screw sizes since they form their own threads when installed.
Use these stud-style anchors with nuts.
Fins prevent these anchors from spinning during installation.
Easy to install, tap these anchors in like a nail—no drilled hole required.
A drilled hole is required for installation.
Also known as Tapcons, use these screws in applications requiring high strength.
These blue and silver ultra-corrosion-resistant coated steel screws stand up to wet environments.
These 410 stainless steel screws are more corrosion resistant than ultra-corrosion-resistant coated steel screws.
Attach the components of these sets onto a hammer drill to install tapping screws in concrete, block, and brick.
Also known as Tapcons, these screws are often used to anchor parts to concrete, block, and brick. Assortments include a drill bit.
A wing-like toggle holds against the back of the material and spreads the force over a large area to hold 30 lbs. or more.
Use these light duty anchors to hold 20 lbs. or less.
Bond new concrete to old concrete, or use this adhesive as a primer on concrete surfaces.
When concrete is saturated or submerged in water, use these adhesives to form strong bonds.
Permanently set threaded rods, studs, and rebar in concrete.
These adhesives maintain their strength at temperatures up to 250° F.
These kits include adhesives, applicators, and mixer nozzles.
The SDS-Plus shank has two deep slots and two shallow slots for use with SDS-Plus-drive rotary hammers.
Insert these bits directly into power screwdrivers, impact drivers, and other tools that accept 1/4" hex shanks.
Use these bits with handheld power drills, drill presses, and hammer drills.