Take tension and compression measurements at 0.1% accuracy—the highest accuracy of all our force gauges. These gauges come with a calibration certificate traceable to NIST that states they’ve passed a test for accuracy. They have a backlit LCD display to easily read measurements, even in low light. The display is reversible, meaning you can detach it, flip it, and reattach it so that the shaft is either on the top or bottom of the gauge. Connect the included attachments to the shaft to grip the material being tested. These gauges have a peak-hold setting that retains the highest reading on the display. Upload your measurements to a computer using the included software.

Read tension and compression measurements with a glance—these gauges have three color-coded indicator lights to show you if a part is at your desired force. Red means the force is too high, orange means too low, and green is just right. These gauges come with a calibration certificate traceable to NIST that states they’ve passed a test for accuracy. They have a backlit LED display to easily read force measurements, even in low light. The display is reversible, so it will be readable whether you have the gauge positioned with the shaft on top or bottom. All have a threaded male shaft to connect tips, hooks, and other attachments. Use the included software to upload measurement data—it downloads peak data from the gauge’s memory or captures continuous data.

Measure the force needed to carry out tasks in your facility, such as pushing carts, pulling pallet trucks, or lifting containers. These testers come with nonslip rubber handles for testing a variety of movements—attach one to the top of the tester or attach both to the sides. For strength analysis, mount padded attachments to the base of the tester to press against a surface. Use the snap hook to suspend loads from the bottom of the tester. It has a snapping clasp to hold loads steady, and it swivels to make sure they’re lined up properly.

With included software, these testers can gather continuous data or select a single data point. They also record the peak force used during a task. Export your measurements to Excel via the USB cable. All come with a calibration certificate traceable to NIST that states they've passed a test for accuracy.

Note: For the most accurate performance, the maximum force you apply should fall near the middle of the tester’s range.

Measure tension force as well as weight. These gauges come with a calibration certificate traceable to NIST that states they've passed a test for accuracy. All are NEMA 4X rated for protection from dust, water, and mild corrosives. They can be manually reset to zero and have a peak-hold setting that retains the highest reading on the display when activated. Also known as dynamometers.

Safely view your tension force measurements on a handheld receiver up to 450 ft. away when moving bulk material with cranes and hoists. These gauges are also called dynamometers and crane scales. Made of steel, they’re durable enough to briefly hold heavy loads up to 500% of their capacity. But, they will no longer take measurements if the load exceeds 200%. Warning lights will flash first when your load exceeds capacity, then again when it reaches 133% capacity. To prevent overloads, the peak-hold setting displays the highest measurement. The tare function lets you reset the gauge to zero after attaching a container to weigh only the material inside. These gauges include a calibration certificate traceable to NIST that states they’ve passed a test for accuracy. They also meet IEC and ASME safety and fatigue standards.

Because their indicators and load cells are IP rated, these gauges stand up to washdowns and brief submersion common to food and chemical plants. They’re also safe to use outdoors since they’re NEMA rated to seal out weather.

These gauges come with two shackles that work with other lifting fittings, such as clevis hooks. The included batteries power their load cells for up to 2,000 hours.

Determine if an adhesive or an epoxy creates a strong enough bond on a surface. Often used in construction and manufacturing, these testers measure the amount of force needed before an adhesive pulls off. They run on batteries, so you can use them anywhere around your facility or jobsite. Transfer data, such as the date and time of each test, to your computer with the included USB—no software download needed. All meet ASTM and ISO standards for adhesion testing.

The 20 mm dollies that come with these testers are the most common and work well for super glue and standard epoxies. To test, attach a dolly to your surface and wait until the adhesive has fully cured. For the best results, score or separate the test area from the surrounding surface with the included cutter before pressing the tester down onto the dolly.

Check the tension of your machine’s flat, timing, or V-belt—no matter its width. These gauges use ultrasonic sound waves to take noncontact readings. To measure, simply pluck the belt like a guitar string to create vibration. Because they don't touch the belt, they won't accidentally change the tension like a traditional gauge might.

For gauges without a keypad, you’ll need to manually calculate your belt’s rating in pounds or newtons using its hertz rating, weight, and length.

Measure the compressive strength of concrete. These testers are often used in the construction industry to assess the quality and integrity of poured concrete. An OLED display gives clear readings, even from wide viewing angles. The rebound body, which is separable from the display, can be used up to 2,000 times before you need to replace it. It's also known as a rebound hammer. For accurate results, create a smooth surface on your concrete with the sanding stone before testing. Export test reports and strength curves with the included software.