McMaster-Carr logo
    Filter by
    Roller Chain Trade Number
    System of Measurement
    Number of Teeth
    Bore Type
    Strand Type
    Shaft Type
    Chain Standard
    Overall Width
    Material
    Sprocket Type
    Chain Type
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    DFARS Specialty Metals
    Bearing Type
    Shaft Mount Type
    Bearing Material
    Tooth Heat Treatment
    Heat Treatment
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    10 Products

    Sprockets

    Image of Product. Front orientation. Drive Sprockets. Sprockets, For Single Strand.

    For Single Strand

    Sprocket teeth mesh with your roller chain to smoothly transmit power. These U.S.-made sprockets have machined teeth for a more precise fit than flame-cut or punched teeth, allowing them to glide in and out of the chain to reduce wear and extend chain life.
    Steel—Steel is strong, but best for dry environments since moisture will cause it to rust.
    Plain Bore—Plain bore sprockets give you options—machine a custom bore, weld, or press-fit them in place. They're sized to the minimum shaft diameter listed and are machinable up to the maximum.
    For
    Roller Chain
    Trade
    No.
    Std.
    Pitch
    No. of
    Teeth
    OD
    Bore
    Type
    For Shaft Dia.
    Each
    For Single Strand
     
    Steel
    140ANSI1 3/4"117.01"Plain1 1/2" to 2 3/4"000000000000000
    140ANSI1 3/4"127.58"Plain1 1/2" to 3"00000000000000
    140ANSI1 3/4"138.15"Plain1 1/2" to 3 5/16"00000000000000
    140ANSI1 3/4"148.72"Plain1 1/2" to 3 3/4"00000000000000
    140ANSI1 3/4"159.28"Plain1 1/2" to 4 1/4"00000000000000
    140ANSI1 3/4"169.85"Plain1 1/2" to 4 1/4"00000000000000
    140ANSI1 3/4"1810.98"Plain1 1/2" to 4 1/4"00000000000000
    140ANSI1 3/4"2012.1"Plain1 1/2" to 4 1/4"0000000000000000
    140ANSI1 3/4"2414.34"Plain1 1/2" to 4 1/4"0000000000000000
     

    Idler Sprockets

    Maintain constant tension on your roller chain to reduce wear and vibration. These sprockets press against the chain to take up slack and rotate freely on bearings to keep the chain moving smoothly. They’re often paired with roller chain tensioners.
    For Single Strand
    Image of Product. Front orientation. Idler Sprockets. For Single Strand, Needle-Roller Bearing.

    Needle-Roller

    Bearing

    Needle-Roller Bearing—These bearings rotate smoothly under your heaviest loads.
    Wear-Resistant Steel with Hardened Teeth—These sprockets have teeth that are hardened from the tip to the base so they withstand chain contact and wear evenly. That means fewer broken teeth and a longer lifespan than sprockets with unhardened or tip-hardened teeth. Steel is best for dry environments since moisture will cause it to rust.
    For
    Roller Chain
    Trade
    No.
    Std.
    Pitch
    No. of
    Teeth
    For Shaft
    Dia.
    OD
    Bearing
    Material
    Each
    Needle-Roller Bearing
     
    Wear-Resistant Steel with Hardened Teeth
    140ANSI1 3/4"111 1/2"7.01"Bronze000000000000000
     
    back to top