Fasten hard-to-bond plastics, such as polypropylene and polyethylene.

Mixed with rubber for better impact resistance than standard instant-bond adhesives, these adhesives form strong, resilient bonds.

To invisibly bond transparent plastics, these adhesives won’t turn cloudy.

Make strong, instant bonds on a variety of materials—but not your skin.

Form bonds without the strong odor of other instant-bond adhesives.

Bond plastics, porous materials, or dirty surfaces.

These super glues are blended with rubber for better impact and moisture resistance than other instant-bond adhesives.

These thin liquids, also known as super glue, flow into small gaps.

To invisibly bond transparent plastics, these adhesives won’t turn cloudy.

For easy positioning, these adhesives begin to harden only when exposed to light.

Moisture, humidity, and immersion in water won't degrade the bond of these adhesives.

Toughened adhesives are blended with rubber particles for better impact resistance than standard epoxies. They form flexible, resilient bonds.

Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. They work especially well on metals.

Assortments include eight different epoxies in 0.1-oz. packets to handle a variety of small jobs.

Fasten hard-to-bond plastics, such as polypropylene and polyethylene, with these epoxies.

These machinable epoxies are mixed with steel, but won’t rust, so they can be used to repair cracks and threaded holes.

These self-extinguishing epoxies meet UL 94 V-0 for flame retardance.

No need to mix these acrylics—apply adhesive to one surface and activator to the other, then bring surfaces together to bond.

Toughened adhesives are blended with rubber particles for better impact resistance than standard acrylics. They form resilient bonds.

Solvents, oils, acids, and other chemicals won't degrade the bond of these adhesives.

With high shear strength and peel strength, these form the strongest bonds of our urethane adhesives.

In addition to being waterproof, this glue is made of FDA listed materials.

Also known as Gorilla Glue, this glue expands to form stronger bonds than other glue.

The 3M VHB adhesive on these rolls offers a strong hold that can replace rivets, spot welds, and other permanent fasteners.

Use these glue rolls with 3M dispensing guns.

Temporarily stabilize objects on flat surfaces with this clear, reusable adhesive.

This putty-like glue cures into a pliable rubber. Use it to repair seals and cracks, or mold it into hooks and bumpers.

These small tabs of pressure-sensitive adhesive offer convenient, no-mess bonding.

When heated, these glue sticks melt and quickly begin to harden. Use them to seal packaging and form other low- to medium-strength bonds.

Glue hardens in 15 seconds or less to bond quickly.

Form bonds with twice the strength of our other spray adhesives.

For easy positioning, this adhesive remains tacky for hours. Once items are in place, apply pressure to create a permanent bond.

Bonds reach full strength in 10 minutes.

These adhesives resist temperatures up to 500° F.

Form strong bonds on most plastics.

Because this cement won't break down when exposed to corrosive waste, it's often used on plastic pipe fittings in laboratories.

Rubber cement allows repositioning until fully dried. Use it on paper and cardboard.

Install building materials such as wood and drywall with these general purpose adhesives.

Bond carpeting, vinyl tile, and other floor coverings to subfloors.

Bond and repair nosing and stair treads with this thick, two-part epoxy.

Adhere vinyl and rubber wall bases to wood, drywall, and concrete.

Tack wires to coil forms or secure and insulate hardware on printed circuit boards. These adhesives require an accelerator.

These kits include adhesives, applicators, and mixer nozzles.

When concrete is saturated or submerged in water, use these adhesives to form strong bonds.

Use these guns to dispense two-part adhesives. Do not use them with 3M dual cartridges.

Dispense two-part adhesives with compressed air. Use these guns only with 3M dual cartridges.

Use these plungers with a 3M dispensing gun for adhesives in dual cartridges.

Fill these cartridges with the two-part adhesive of your choice.

Use these dispensing guns with Loctite® single-component syringes.

Guns are powered with compressed air for controlled dispensing on small and large jobs alike.

Thread these holders onto a gun to hold an adhesive cartridge.

A quick disconnect bayonet connection attaches these holders to a gun to hold an adhesive cartridge in place.

Dispense up to 3 times as much adhesive per hour as our standard hot-melt glue guns.

Don't be tethered by a cord—take these guns where they're needed.

Use these guns in heat-sensitive applications and on delicate materials. They have a temperature setting of 250° F.

Butane power makes these guns completely portable.

Convert glue guns for use with 8" long glue sticks.

Choose from cone tips, L-tips, and T-tips.

Use these guns for easy dispensing of 3M glue-on-a-roll.

Brushes have natural bristles and a wood handle.

For easy cleanup, these trowels are disposable. They have V- or square-shaped notches.

Cover adhesive and sealant cartridges to keep contents from hardening.

Keep cups and sticks on hand for mixing two-part adhesives.

Store adhesives, cements, and lacquers for up to two weeks without hardening.

Prepare PVC and CPVC pipe for bonding.

To speed cure time on coated fasteners, aluminum, stainless steel, or titanium, apply these primers before using threadlocker or retaining compound. They also work with no-mix acrylic adhesives.

Activators are required for no-mix acrylic structural adhesives to create adhesion.

Specially formulated for plastics, these threadlockers secure nylon, PTFE, and other plastic threaded fasteners.

These low-friction threadlockers harden slowly, allowing ample time to smoothly adjust multiple large bolts for even clamping.

Use these threadlockers on fasteners that require occasional fine-tuning, such as set screws.

These threadlockers develop usable strength within one hour. Because they harden quickly on most metals, they don't require a primer.

Paste threadlockers are easy to apply and won't drip, even from overhead fasteners.

This gel clings to fasteners to prevent drips.

Wrap this no-mess tape around threaded fasteners up to 30 days before installation.

These threadlockers withstand temperatures up to 450° F.

Even on oily surfaces, these retaining compounds keep their hold.

Fill gaps up to 0.02" to secure worn unthreaded cylindrical metal parts such as shafts, bearings, and press-fit assemblies.

These sealants include a material certificate with traceable lot number, test report, and product shelf life.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Also known as neutral-cure sealants, these won't discolor copper, brass, and concrete.

A combination of hardness and surface tension makes these sealants resistant to punctures, cuts, and abrasion.

Apply these sealants in cold temperatures, on wet surfaces, and even through running water.