About Hinges
More
About Rod Ends
More
Easy-Lube Narrow-Profile Lift-Off Hinges without Holes
Hinge with 360°
Range of Motion
A grease fitting makes these hinges easy to lubricate. Also known as bullet hinges, these hinges are the right size for tight spaces and narrow frames. The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin. All of the hinges have a small triangular surface to weld to the door frame.
Aluminum hinges are about half the weight of low-carbon steel. They have mild corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Hinges | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Door Leaf | Frame Leaf | Replacement Bushings | ||||||||||
| Ht. | Wd. | Ht. | Wd. | O'all Wd. | Range of Motion | Pin Dia. | Material | Pin Material | Each | Each | ||
Low-Carbon Steel—Dull | ||||||||||||
| 1 17/32" | 1/2" | 1 17/32" | 1/2" | 1/2" | 360° | 5/16" | Low-Carbon Steel | Brass | 000000 | 00000 | 00000000 | 00000 |
| 1 15/16" | 5/8" | 1 15/16" | 5/8" | 5/8" | 360° | 25/64" | Low-Carbon Steel | Brass | 000000 | 0000 | 00000000 | 0000 |
| 2 5/16" | 5/8" | 2 5/16" | 5/8" | 5/8" | 360° | 25/64" | Low-Carbon Steel | Brass | 000000 | 00000 | 00000000 | 0000 |
| 2 9/16" | 23/32" | 2 9/16" | 23/32" | 23/32" | 360° | 1/2" | Low-Carbon Steel | Low-Carbon Steel | 0000000 | 00000 | 00000000 | 0000 |
| 2 15/16" | 25/32" | 2 15/16" | 25/32" | 25/32" | 360° | 1/2" | Low-Carbon Steel | Brass | 000000 | 00000 | 00000000 | 0000 |
| 3 17/32" | 25/32" | 3 17/32" | 25/32" | 25/32" | 360° | 1/2" | Low-Carbon Steel | Brass | 000000 | 00000 | 00000000 | 0000 |
| 3 31/32" | 29/32" | 3 31/32" | 29/32" | 29/32" | 360° | 5/8" | Low-Carbon Steel | Brass | 000000 | 00000 | 00000000 | 0000 |
| 5 3/32" | 1 3/32" | 5 3/32" | 1 3/32" | 1 3/32" | 360° | 3/4" | Low-Carbon Steel | Low-Carbon Steel | 0000000 | 00000 | 00000000 | 0000 |
Aluminum—Dull | ||||||||||||
| 1 1/2" | 1/2" | 1 17/32" | 1/2" | 1/2" | 360° | 5/16" | 6063 Aluminum | 304 Stainless Steel | 0000000 | 0000 | 00000000 | 0000 |
| 1 15/16" | 5/8" | 1 15/16" | 5/8" | 5/8" | 360° | 25/64" | 6063 Aluminum | 304 Stainless Steel | 0000000 | 00000 | 0000000 | 0000 |
| 2 7/8" | 13/16" | 2 15/16" | 13/16" | 13/16" | 360° | 1/2" | 6063 Aluminum | 304 Stainless Steel | 0000000 | 00000 | 00000000 | 0000 |
Ball Joint Rod Ends with Grease Fitting
Connect your grease gun to the fitting to lubricate. Made of steel, these rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.
For technical drawings and 3-D models, click on a part number.
Shank | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Center Lg. | Thread Lg. | Thread Pitch | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
| 3/8"-24 | 3/8" | 22° | 1" | 1/2" | 1 15/16" | 1 1/4" | __ | 3,500 | Carbon Steel | 000000 | 00000 | |
| 7/16"-20 | 7/16" | 21° | 1 1/8" | 9/16" | 2 1/8" | 1 3/8" | __ | 4,450 | Carbon Steel | 000000 | 0000 | |
| 1/2"-20 | 1/2" | 20° | 1 5/16" | 5/8" | 2 7/16" | 1 1/2" | __ | 5,850 | Carbon Steel | 000000 | 0000 | |
| 5/8"-18 | 5/8" | 26° | 1 1/2" | 3/4" | 2 5/8" | 1 5/8" | __ | 6,850 | Carbon Steel | 000000 | 0000 | |
| 3/4"-16 | 3/4" | 24° | 1 3/4" | 7/8" | 2 7/8" | 1 3/4" | __ | 9,400 | Carbon Steel | 000000 | 00000 | |
| 1"-12 | 1" | 17° | 2 3/4" | 1 3/8" | 4 1/8" | 2 1/8" | __ | 37,000 | Carbon Steel | 000000 | 00000 | |
| 1"-14 | 1" | 17° | 2 3/4" | 1 3/8" | 4 1/8" | 2 1/8" | __ | 37,000 | Carbon Steel | 000000 | 00000 | |
| M10 | 10mm | 26° | 27mm | 14mm | 48mm | 29mm | 1.25mm | 4,700 | Carbon Steel | 0000000 | 00000 | |
| M10 | 10mm | 26° | 27mm | 14mm | 48mm | 29mm | 1.5mm | 4,700 | Carbon Steel | 0000000 | 00000 | |
| M12 | 12mm | 27° | 30mm | 16mm | 54mm | 33mm | 1.25mm | 5,800 | Carbon Steel | 0000000 | 00000 | |
| M12 | 12mm | 27° | 30mm | 16mm | 54mm | 33mm | 1.75mm | 5,800 | Carbon Steel | 0000000 | 00000 | |
| M14 | 14mm | 30° | 34.8mm | 19mm | 60mm | 36mm | 2mm | 7,900 | Carbon Steel | 0000000 | 00000 | |
| M16 | 16mm | 33° | 38mm | 21mm | 66mm | 40mm | 2mm | 8,400 | Carbon Steel | 0000000 | 00000 | |
| M18 | 18mm | 30° | 42mm | 23mm | 72mm | 44mm | 1.5mm | 10,750 | Carbon Steel | 0000000 | 00000 | |
| M20 | 20mm | 29° | 46mm | 25mm | 78mm | 47mm | 1.5mm | 12,800 | Carbon Steel | 0000000 | 00000 | |
Internally Threaded Ball Joint Rod Ends with Grease Fitting
Connect your grease gun to the fitting to lubricate. These rod ends don’t come lubricated, so you'll need to lubricate during installation and on an ongoing basis. Made of steel, they generally handle higher loads than stainless steel, aluminum, and nylon rod ends.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
| 3/8"-24 | 3/8" | 22° | 1" | 1/2" | 1 5/8" | 13/16" | 5,100 | Carbon Steel | 0000000 | 00000 | |
| 7/16"-20 | 7/16" | 21° | 1 1/8" | 9/16" | 1 13/16" | 15/16" | 6,400 | Carbon Steel | 0000000 | 0000 | |
| 1/2"-20 | 1/2" | 20° | 1 5/16" | 5/8" | 2 1/8" | 1 1/16" | 9,100 | Carbon Steel | 0000000 | 0000 | |
| 5/8"-18 | 5/8" | 26° | 1 1/2" | 3/4" | 2 1/2" | 1 3/8" | 9,800 | Carbon Steel | 0000000 | 0000 | |
| 3/4"-16 | 3/4" | 24° | 1 3/4" | 7/8" | 2 7/8" | 1 9/16" | 14,250 | Carbon Steel | 0000000 | 00000 | |
| 1"-12 | 1" | 17° | 2 3/4" | 1 3/8" | 4 1/8" | 2 1/8" | 43,500 | Carbon Steel | 0000000 | 00000 | |
| 1"-14 | 1" | 17° | 2 3/4" | 1 3/8" | 4 1/8" | 2 1/8" | 43,500 | Carbon Steel | 0000000 | 00000 | |
| M6 × 1 mm | 6mm | 23° | 19mm | 9mm | 30mm | 14mm | 2,650 | Carbon Steel | 000000 | 0000 | |
| M8 × 1.25 mm | 8mm | 28° | 22.3mm | 12mm | 36mm | 17mm | 3,400 | Carbon Steel | 000000 | 0000 | |
| M10 × 1.5 mm | 10mm | 26° | 27mm | 14mm | 43mm | 21mm | 5,100 | Carbon Steel | 000000 | 0000 | |
| M12 × 1.75 mm | 12mm | 27° | 30mm | 16mm | 50mm | 24mm | 5,800 | Carbon Steel | 000000 | 00000 | |
| M14 × 2 mm | 14mm | 30° | 34.8mm | 19mm | 57mm | 27mm | 7,900 | Carbon Steel | 000000 | 00000 | |
| M16 × 2 mm | 16mm | 33° | 38mm | 21mm | 64mm | 33mm | 8,400 | Carbon Steel | 000000 | 00000 | |
| M20 × 1.5 mm | 20mm | 29° | 46mm | 25mm | 77mm | 40mm | 12,800 | Carbon Steel | 000000 | 00000 |
Oil-Embedded Ball Joint Rod Ends with Grease Fitting
An oil-embedded bronze insert slowly releases lubricant to the rod end. Relubrication is recommended but not required. Connect your grease gun to the fitting to relubricate. Made of zinc-plated steel, these rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends and offer moderate corrosion resistance.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID, mm | Max. Ball Swivel | O'all Wd., mm | O'all Thick., mm | Shank Center Lg., mm | Shank Thread Lg., mm | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
| M8 × 1.25 mm | 8 | 18° | 22 | 12 | 42 | 25 | 4,000 | Zinc-Plated Carbon Steel | 0000000 | 000000 | |
| M10 × 1.5 mm | 10 | 17° | 27 | 14 | 48 | 29 | 6,250 | Zinc-Plated Carbon Steel | 0000000 | 00000 | |
| M12 × 1.75 mm | 12 | 17° | 30 | 16 | 54 | 33 | 7,750 | Zinc-Plated Carbon Steel | 0000000 | 00000 |
Internally Threaded Oil-Embedded Ball Joint Rod Ends with Grease Fitting
An oil-embedded bronze insert slowly releases lubricant to the rod end. Relubrication is recommended but not required. Connect your grease gun to the fitting to relubricate. Made of zinc-plated steel, these rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends and offer moderate corrosion resistance.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID, mm | Max. Ball Swivel | O'all Wd., mm | O'all Thick., mm | Shank Center Lg., mm | Shank Thread Lg., mm | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
| M8 × 1.25 mm | 8 | 18° | 22 | 12 | 36 | 17 | 4,000 | Zinc-Plated Carbon Steel | 0000000 | 000000 | |
| M10 × 1.5 mm | 10 | 17° | 27 | 14 | 43 | 21 | 6,250 | Zinc-Plated Carbon Steel | 0000000 | 00000 | |
| M12 × 1.75 mm | 12 | 17° | 30 | 16 | 50 | 24 | 7,750 | Zinc-Plated Carbon Steel | 0000000 | 00000 |
Internally Threaded Ball Joint Linkages with Grease Fitting
Along with superior wear resistance, these linkages have a grease fitting for easy lubrication. They consist of ball joint rod ends with a ball stud attached to simplify mounting. The stud is machined to fit perfectly inside its housing and swivel in all directions—good for clutches, throttles, and shift control rods. These linkages don't come lubricated, so you'll need to lubricate during installation and on an ongoing basis.
For technical drawings and 3-D models, click on a part number.
Shank | Ball Stud | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Thread Size | Center Lg. | Thread Lg. | Thread Size | Center Lg. | Lg. | Max. Ball Swivel | Static Radial Load Cap. | Material | Each | |
Right-Hand Threaded Ball Stud | ||||||||||
Right-Hand Threaded Shank | ||||||||||
| 1/4"-28 | 1 5/16" | 11/16" | 1/4"-28 | 1 1/32" | 9/16" | 40° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 5/16"-24 | 1 3/8" | 11/16" | 5/16"-24 | 1 7/32" | 11/16" | 42° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 0000 |
| 3/8"-24 | 1 5/8" | 13/16" | 3/8"-24 | 1 9/16" | 29/32" | 46° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 0000 |
| 7/16"-20 | 1 13/16" | 15/16" | 7/16"-20 | 1 3/4" | 1 1/16" | 44° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 1/2"-20 | 2 1/8" | 1 1/16" | 1/2"-20 | 2" | 1 1/8" | 48° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 5/8"-18 | 2 1/2" | 1 3/8" | 5/8"-18 | 2 1/2" | 1 1/2" | 52° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 3/4"-16 | 2 7/8" | 1 9/16" | 3/4"-16 | 3" | 1 13/16" | 46° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
Left-Hand Threaded Shank | ||||||||||
| 5/16"-24 | 1 3/8" | 11/16" | 5/16"-24 | 1 7/32" | 11/16" | 42° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 0000 |
| 3/8"-24 | 1 5/8" | 13/16" | 3/8"-24 | 1 9/16" | 29/32" | 46° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 0000 |
| 1/2"-20 | 2 1/8" | 1 1/16" | 1/2"-20 | 2" | 1 1/8" | 48° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 5/8"-18 | 2 1/2" | 1 3/8" | 5/8"-18 | 2 1/2" | 1 1/2" | 52° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 3/4"-16 | 2 7/8" | 1 9/16" | 3/4"-16 | 3" | 1 13/16" | 46° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
Left-Hand Threaded Ball Stud | ||||||||||
Right-Hand Threaded Shank | ||||||||||
| 3/8"-24 | 1 5/8" | 13/16" | 3/8"-24 | 1 9/16" | 29/32" | 46° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 0000 |
| 1/2"-20 | 2 1/8" | 1 1/16" | 1/2"-20 | 2" | 1 1/8" | 48° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
Left-Hand Threaded Shank | ||||||||||
| 1/2"-20 | 2 1/8" | 1 1/16" | 1/2"-20 | 2" | 1 1/8" | 48° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
Ball Joint Linkages with Grease Fitting
Along with superior wear resistance, these linkages have a grease fitting for easy lubrication. They consist of ball joint rod ends with a ball stud attached to simplify mounting. The stud is machined to fit perfectly inside its housing and swivel in all directions—good for clutches, throttles, and shift control rods. They don’t come lubricated, so you’ll need to lubricate them during installation and on an ongoing basis.
For technical drawings and 3-D models, click on a part number.
Shank | Ball Stud | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Thread Size | Center Lg. | Thread Lg. | Thread Size | Center Lg. | Lg. | Max. Ball Swivel | Static Radial Load Cap. | Material | Each | |
Right-Hand Threaded Ball Stud | ||||||||||
Right-Hand Threaded Shank | ||||||||||
| 3/8"-24 | 1 15/16" | 1 1/4" | 3/8"-24 | 1 9/16" | 29/32" | 46° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 7/16"-20 | 2 1/8" | 1 3/8" | 7/16"-20 | 1 3/4" | 1 1/16" | 44° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 1/2"-20 | 2 7/16" | 1 1/2" | 1/2"-20 | 2" | 1 1/8" | 48° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 5/8"-18 | 2 5/8" | 1 5/8" | 5/8"-18 | 2 1/2" | 1 1/2" | 52° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 3/4"-16 | 2 7/8" | 1 3/4" | 3/4"-16 | 3" | 1 13/16" | 46° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
Left-Hand Threaded Shank | ||||||||||
| 3/8"-24 | 1 15/16" | 1 1/4" | 3/8"-24 | 1 9/16" | 29/32" | 46° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 0000 |
| 7/16"-20 | 2 1/8" | 1 3/8" | 7/16"-20 | 1 3/4" | 1 1/16" | 44° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 1/2"-20 | 2 7/16" | 1 1/2" | 1/2"-20 | 2" | 1 1/8" | 48° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 5/8"-18 | 2 5/8" | 1 5/8" | 5/8"-18 | 2 1/2" | 1 1/2" | 52° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 3/4"-16 | 2 7/8" | 1 3/4" | 3/4"-16 | 3" | 1 13/16" | 46° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
Left-Hand Threaded Ball Stud | ||||||||||
Right-Hand Threaded Shank | ||||||||||
| 3/8"-24 | 1 15/16" | 1 1/4" | 3/8"-24 | 1 9/16" | 29/32" | 46° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 0000 |
| 1/2"-20 | 2 7/16" | 1 1/2" | 1/2"-20 | 2" | 1 1/8" | 48° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
Left-Hand Threaded Shank | ||||||||||
| 1/2"-20 | 2 7/16" | 1 1/2" | 1/2"-20 | 2" | 1 1/8" | 48° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
| 3/4"-16 | 2 7/8" | 1 3/4" | 3/4"-16 | 3" | 1 13/16" | 46° | Not Rated | Zinc-Plated Carbon Steel | 00000000 | 00000 |
High-Torque Single U-Joints
With a maximum torque of at least 11,600 in.-lbs., these U-joints handle more torque than any other U-joint in our offering. They’re single U-joints, meaning they connect and transfer torque between shafts that are misaligned at an angle. Often found in continuously running applications, they operate at higher speeds and last longer than other types of joints, thanks to their needle bearings.
Connect these U-joints to shafts using the included set screws. Unlike U-joints that use spring pins, there’s no drilling required. All have a grease fitting, so you can use a grease gun to lubricate all of the bearings at once.
Your shafts’ misalignment will affect the speed and torque the U-joint will be able to transmit. The more the shafts are misaligned, the less speed and torque the U-joint will be able to transmit.
Steel U-joints are stronger and handle more torque than iron U-joints.
For technical drawings and 3-D models, click on a part number.
For Shaft | O'all | Keyway | Torque | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Dp. | Joint Dia. | Ht. | Lg. | Wd. | Dp. | Max. Operating Angle | Max. Speed, rpm | Max. Torque, in.-lbs. | 3° Operating Angle | 10° Operating Angle | Includes | Each | |
Iron with Steel Bearings | ||||||||||||||
| 3/4" | 1 13/64" | 1 5/8" | 2 3/8" | 5" | 3/16" | 3/32" | 45° | 1,000 | 11,600 | 1,260 in.-lbs. @ 1,000 rpm | 720 in.-lbs. @ 1,000 rpm | Grease Fitting | 000000 | 0000000 |
| 7/8" | 1 13/64" | 1 5/8" | 2 3/8" | 5" | 3/16" 1/4" | 3/32" 1/8" | 45° | 1,000 | 11,600 | 1,260 in.-lbs. @ 1,000 rpm | 720 in.-lbs. @ 1,000 rpm | Grease Fitting | 000000 | 000000 |
| 1" | 1 13/64" | 1 5/8" | 2 3/8" | 5" | 3/16" 1/4" | 3/32" 1/8" | 45° | 1,000 | 11,600 | 1,260 in.-lbs. @ 1,000 rpm | 720 in.-lbs. @ 1,000 rpm | Grease Fitting | 000000 | 000000 |
| 1 1/8" | 1 5/32" | 2 1/4" | 2 5/16" | 5" | 1/4" 5/16" | 1/8" 5/32" | 45° | 1,000 | 11,600 | 1,260 in.-lbs. @ 1,000 rpm | 720 in.-lbs. @ 1,000 rpm | Grease Fitting | 000000 | 000000 |
| 1 1/4" | 1 5/32" | 2 1/4" | 2 5/16" | 5" | 1/4" 5/16" | 1/8" 5/32" | 45° | 1,000 | 11,600 | 1,260 in.-lbs. @ 1,000 rpm | 720 in.-lbs. @ 1,000 rpm | Grease Fitting | 000000 | 000000 |
Steel with Steel Bearings | ||||||||||||||
| 3/4" | 1 29/64" | 2" | 2 5/8" | 5 1/2" | 3/16" | 3/32" | 45° | 1,000 | 22,700 | 2,220 in.-lbs. @ 1,000 rpm | 1,260 in.-lbs. @ 1,000 rpm | Grease Fitting | 0000000 | 000000 |
| 7/8" | 1 29/64" | 2" | 2 7/16" | 5 1/2" | 1/4" | 1/8" | 45° | 1,000 | 22,700 | 2,220 in.-lbs. @ 1,000 rpm | 1,260 in.-lbs. @ 1,000 rpm | Grease Fitting | 0000000 | 000000 |
| 1" | 2" | 2 1/16" | 2 5/8" | 7" | 3/16" 1/4" | 3/32" 1/8" | 45° | 1,000 | 22,700 | 2,220 in.-lbs. @ 1,000 rpm | 1,260 in.-lbs. @ 1,000 rpm | Grease Fitting | 0000000 | 000000 |
| 1 1/4" | 1 3/16" | 2 1/4" | 2 5/8" | 5 1/2" | 1/4" | 1/8" | 45° | 1,000 | 22,700 | 2,220 in.-lbs. @ 1,000 rpm | 1,260 in.-lbs. @ 1,000 rpm | Grease Fitting | 0000000 | 000000 |
| 1 1/2" | 1 3/16" | 2 1/4" | 2 5/8" | 5 1/2" | 3/8" | 3/16" | 45° | 1,000 | 22,700 | 2,220 in.-lbs. @ 1,000 rpm | 1,260 in.-lbs. @ 1,000 rpm | Grease Fitting | 0000000 | 000000 |