These switches meet MIL-S-3950.

Because these switches mount flush against a panel, they're easy to clean and hard to damage.

Mount these switches in panel cutouts where changing a battery or routing wires might be difficult—they power themselves when you push the button.

A quick push is all it takes to actuate these switches.

Save space on your panel by using one switch for several tasks. These switches actuate with the push of a button.

A base that lights up draws attention to emergency stops. When pushed, these switches immediately cut power.

Install in 12 mm dia. cutouts.

More durable than standard metal switches, these can handle tough, repetitive use.

Actuate these switches with a quick push. A housing seals in anything that could ignite flammable material, so you can use them where ignitable gas and dust may be present.

Save space on a panel by using one switch to perform multiple switching functions.

Immediately cut power with a single push.

Because these switches mount flush against a panel, they're easy to clean and hard to damage.

Immediately cut power with a single push.

Immediately cut power with a single push.

Snap these switches onto your T-slotted framing rails—no need to drill or disassemble your existing structure.

These familiar push-button switches mount to flat surfaces.

Use these switches where ignitable gas and dust may be present. They're rated for use in hazardous locations.

A red light flashes when the actuator is pushed, making it easy to see from a distance. They're rated IP65 for protection from washdowns.

A protective plastic enclosure resists dents, chips, and cracks, so you can install these switches outside of panels.

Rated NEMA 6P and IP68, these switches are protected against washdowns, corrosion, and temporary submersion.

Control equipment from up to 40 feet away—these switches include a transmitter and a receiver that connects to equipment.

Keep your hands free for other tasks by triggering switches with your foot.

When the pedal is pressed, the built-in potentiometer adjusts the resistance to vary the speed for motor drives.

These switches withstand temporary submersion.

Control cranes and other mobile machinery in dirty, outdoor, and wet environments without damaging your switch.

Operate equipment from up to 330 feet away—these switches include a transmitter and a receiver that connects to equipment.

Use these switches where ignitable gas, dust, and fibers may be present. They're UL and C-UL listed for hazardous locations.

Prevent accidental actuation from bumps or jostles—these switches require you grip and twist a lever to turn them on or off. Install them in 30 mm dia. cutouts.

Made for areas where ignitable gas and vapor may be present, these switches have a housing that seals in anything that could spark flammable material.

Prevent accidental actuation from bumps or vibration—these switches require you to grip and twist the lever to turn the switch. The contact block and actuator are all one piece, so they won’t separate in high-vibration applications.

Rated IP67 for protection from dust and temporary submersion.

To prevent accidental actuation and limit access to sensitive equipment, these switches require a key to turn circuits on or off. The contact block and actuator are all one piece, so they won’t separate in high-vibration applications.

Control circuits with the tap of an RFID tag. Since each tag has a unique digital code, these switches aren’t just quicker to use than those with a traditional key—they’re also more secure.

Designed for use near ignitable gases, fibers, and dust, these switches have a housing that seals in anything that could ignite flammable material. They require a key to turn circuits on or off, preventing accidental activation and limiting access.

Tug the hanging rope to actuate these switches.

Safe to use near ignitable gases and dust, the housing on these switches seals in anything that could ignite flammable material. Yank the cable anywhere along your line to quickly cut power in emergencies.

Prevent personnel from getting too close to dangerous equipment while it’s running. Step anywhere on these mats and they can turn on warning lights and alarms or shut down equipment.

Thicker than standard safety switch mats, these withstand repeated impact from heavy and sharp objects.

Use fingerprints to confirm the identity of personnel before granting access to secure areas or equipment.

Choose an actuator and contact block to make your own 22 mm metal switch.

Choose an actuator and contact block to make your own 16 mm switch.

Turn these switches by hand.

When a moving object contacts the actuator on these switches, they open or close a circuit. They have the rapid-closing action of a snap-acting switch, but with a larger actuator for large objects.

Rugged enough for mining operations, these limit switches require a high actuation force, like heavy rocks moving on a conveyor.

Start or stop equipment after a set number of rotations to avoid over-rotation.

Install these limit switches where changing a battery or routing wires might be difficult—they power themselves when a moving object contacts the actuator.

Prevent equipment from automatically restarting—these switches must be manually reset each time they're actuated.

A sealed actuator prevents these switches from jamming, even when exposed to sand, mud, or dirt. With a slim design, you can stack them together or fit them in tight spaces.

Secure these switches into panel cutouts using mounting nuts. They have a slim body so they can also be stacked together or fit into tight spaces.

Open and close circuits in a snap—even in harsh conditions. With a rubber-encased housing and stainless steel bracket, these switches handle high vibrations and resist corrosion. They’re rated IP68 for protection from dust and temporary submersion.

Keep out dirt and moisture—the sealed housing on these switches is watertight and meets MIL-PRF-8805.

Rated IP67, these switches have an enclosure that shields their interior during temporary submersion. They open and close circuits in a snap—their quick actuation minimizes arcing and keeps contacts from sticking.

Replace the hinges on access doors or machine guards with these switches to keep your team safe from active machinery.

Also known as interlock switches, these ensure the safety of personnel by automatically shutting off power to machinery when an access door opens. They’re often used with machine guards.

Delay access to hazardous areas until conditions are safe; use these switches with machines that take time to stop after they are turned off. They mount to a door frame.

Prevent automatic doors from closing on a person or an object—these switches immediately turn machinery off when actuated with minimal force.

Rotate the face on these switches five different directions for easy installation and positioning—they work with both AC and DC inputs.

Easily mount these flat switches to a base or rail.

The short body on these switches makes them suitable for tight spaces.

Turn the face on these switches to sense metallic objects from the front, sides, top, or bottom.

Mount these intrinsically safe switches to flat surfaces in volatile areas. Their low-current, low-voltage NAMUR signal means they won’t ignite or create sparks while in use. ATEX and IECEx certified, they meet international standards to protect against explosion where combustible dust and flammable gases are present.

Use these switches to sense metallic objects in environments containing flammable gases and combustible dust. ATEX and IECEx certified to protect against explosion, they produce a low-current, low-voltage NAMUR signal, so they won’t ignite or create sparks.

Check the position of your torch or workpiece for accuracy during robotic welding.

Sense objects from farther away than with other DC proximity switches that have the same diameter.

For use in volatile areas, these intrinsically safe switches detect objects when they pass through the slot. They use a NAMUR signal to operate at a low current and voltage, so they won’t ignite or create sparks. ATEX and IECEx certified, they protect against explosion.

With a smaller diameter and shorter length than standard sized switches, these fit in the most space-constrained areas.

Switches accept both AC and DC input voltage.