Turn fasteners from either end and reach into tight spots.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

The short bit on these sockets fits in spaces where height clearance is limited.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

With more than double the clearance of standard sockets, these sockets access nuts on extra-long bolts.

Hold fasteners securely in place as you drive them.

Pair these sockets with a bolt-through ratchet wrench to reach nuts at the bottom of a long threaded rod or bolt which can pass through the socket and the head of the wrench.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

Turn multiple shapes and sizes of fasteners with a single socket.

Grip more of your fastener head with these wrench heads.

Designed to fit inside strut channel, these sockets make it easier to mount the channel than using an extension or additional tools.

These sockets are made to withstand the high torque and force of impact tools.

Switch out worn or damaged bits instead of replacing your entire bit socket.

A magnet holds the fastener securely enough to drive self-tapping screws.

Pivot the head to access fasteners from an angle.

Extra length allows access to fasteners on long bolts.

The short bit on these sockets fits in spaces where height clearance is limited.

Suitable for occasional maintenance work, these sets are imported.

Access 6-point nuts and bolts in tight and awkward spaces—the heads on these sockets pivot.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Suitable for occasional maintenance work, these sets are imported.

Pivot the head to access fasteners from an angle.

Reach nuts obstructed by a fluid line or other barrier with the wrench heads in these sets.

Connect one of the heads in these sets to a socket extension to reach an obstructed fastener, then turn the fastener without removing and repositioning the wrench head.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.

Pivot the head to access fasteners from an angle.

Tighten or loosen nuts and bolts without damaging the finish.

Pivot the head to access fasteners from an angle.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

A lever reverses the ratchet direction.

A lever reverses the ratchet direction.

When working in tight spaces, these short wrenches fit where others can't.

Made of materials that are Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Quickly find the wrenches you're looking for with these brightly colored sets.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Flip these wrenches over to ratchet in the opposite direction.

Suitable for occasional maintenance work, these sets are imported.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

The 25° offset heads give you additional clearance to turn hard-to-reach fasteners.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

An insulated handle protects against accidental contact with live electrical circuits. These wrenches are tested to 1,000 volts to meet IEC 60900.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.

Also known as half-moon and obstruction wrenches, the shape lets you reach around obstacles and into machinery.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

These wrenches are made of stainless steel for excellent corrosion resistance.

These are also known as tappet wrenches.

Also known as alligator wrenches and water-meter nut wrenches, the V-shaped head fits multiple hex fastener sizes.

Fit the narrow head into tight spaces and around thin fasteners.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.