The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Snap these grommets into place and their wings expand against the sides of the hole to lock them in position. Use them to turn rough-edged and uneven holes into smooth holes.

These flexible grommets withstand temperatures of 450° F or greater, which is approximately twice as high as our standard grommets. Push them into place to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration.

The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Push these grommets into place. They turn rough-edged and uneven holes into smooth, insulated holes.

A slit in the side of these grommets allows you to install them around wire, cable, and cords that are already in place. They snap into the hole and their wings hold them tight. Use them to turn rough-edged and uneven holes into smooth, insulated holes.

These grommets have two flanges that snap around holes and flex to compensate for misalignment and movement of pipe and tubing. They're often used for routing applications in panel walls.

Create a tight seal around wire, cable, and cords with these grommets to keep out dust, debris, and moisture.

Cut the center of these grommets with a utility knife to create custom IDs. The two‐piece design makes it easy to install and seal these grommets around wire, cable, and cords that are already in place. Use them to keep out dust, debris, and moisture.

Create a sanitary seal on through-wall piping, tubing, and cables in food-, cosmetic-, and pharmaceutical-processing areas.

Wire, cable, and cords pass through the grommet opening while the bristles fill in the gaps to control dust and debris. Use these grommets to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.

Squeeze these flexible grommets to open the center flap—once wire, cable, and cords pass through, the flap closes tightly for dust and debris protection as well as a finished look. Use them to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.

Press these grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

Kits include grommets, a cutting punch, a cutting block, an installation punch, and a die set. Use them to create a way to run rope and cable through tarps, covers, and curtains.

The sharp neck on these grommets cuts the material as you press them into place, eliminating the need for a cutting punch. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

The stem on these bumpers compresses to fit into tight holes. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

All of these bumpers are reinforced with an embedded washer or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Install them with screws.

Mount these bumpers on a threaded stud. All are reinforced with a steel core or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines.

Choose the ID, OD, and length you need.

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part.

Made of durable tungsten carbide, these bushings outlast steel.

The head prevents these bushings from being pushed through the jig when drilling pressure is extreme. The head sits above the jig plate or can be mounted flush by installing in a counterbored hole.

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit.

Replace worn bushings and quickly change IDs without needing to repeatedly use a lever press. Instead of pressing bushings in and out of your jig fixture, which can cause damage, these bushings slide in and out of sleeves.

Twist these lock rings onto bushings to secure them in drilled holes.

The knurls resist force and provide better holding strength than serrations. Encase in plastic tooling.

As you tighten your screw, the rolled collar compresses under the head to create an insulating barrier between a screw shank and a mating surface.

Reinforce holes in soft material to keep them from collapsing around screws.

Once installed, these fasteners provide a female snap half on one side of your fabric and a male snap half on the other.

These female snap halves create the finished button-look of a snap. Pair them with male snap halves to create a complete snap.

Pair these male snap halves with female snap halves to make a complete snap.

In addition to having a wider temperature range than our other vibration-damping bushings, these have excellent weather resistance.

In addition to having a wider temperature range than our other ribbed vibration-damping bushings, these have excellent weather resistance.

Use these in place of normal washers to damp vibration and cushion your joint.

In addition to having a wider temperature range than our other vibration-damping washers, these have excellent weather resistance.

Ribbed grommets are more flexible than our smooth vibration-damping grommets, so they're easier to install.

The cable-entry side has heat-shrinkable polyolefin with an adhesive lining. These are also known as cable-entry seals.

Secure multiple flat cable through one cord grip—reducing the space and number you need for a project, as well as saving time.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.

Tighten the screws to secure your cable.

Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

These cord grips are lightweight yet durable.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Secure and seal electrical cords entering knockouts at a 45° angle.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

These grips install into enclosure holes quickly to stabilize and relieve strain on cords.

Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.

With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Stop cords from coming loose in wet environments while keeping them along the side of your enclosure in tight spaces.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

These 90° elbows absorb less water and are less likely to crack or corrode than other types of plastics and metals.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Also known as cable-entry seals, the cable-entry side has heat-shrinkable polyolefin with an adhesive lining.

The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.