How to Identify and Measure Fittings
Pipe size is an industry designation, not the actual size. View information about how to measure threaded and unthreaded pipe and pipe fittings.
More
Installation Tools for Push-On Barbed Hose Fittings
This tool allows you to connect large quantities of barbed fittings to push-on hose. Use the built-in cutter to squarely cut push-on hose without fraying. Next, lubricate either the push-on hose, fitting or both. Then, clamp the hose into the tool’s vise and apply light pressure on the handle to drive into the fitting.
Mounting Hole | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Hose ID Range | Lg. | Ht. | Dp. | Dia. | No. of | Mounting Fasteners Included | Each | |
| 1/4" to 3/4" | 13 1/2" | 7" | 2 3/8" | 5/8" | 4 | No | 00000000 | 0000000 |
Crimping Tools for Hydraulic Hose Fittings
Permanently seal a crimp-on fitting onto your hydraulic hose to create a leak-tight connection. Bring these crimpers with you to put together hose assemblies on the spot—no need to lug hoses back to your shop. Made in the U.S., these tools are compatible with a wide range of Parker hoses and fittings. Slide your hydraulic hose fully into the crimp-on fitting and use these tools to crimp the connection.
Manual crimping tools are powered by a hand pump. Insert your hose and fitting and manually pump until the die ring touches the base plate.
Air-powered crimping tools don’t require any pumping but do require a compressed air line. Insert your hose and fitting and pull the activation lever until the die ring touches the base plate.
Dies are required to crimp. Choose one that matches your hose diameter and hose fitting series. They’re color coded, so they’re easy to tell apart.
| For Hose Fitting Manufacturer Series | For Hose Manufacturer Series | For Maximum Hose ID | Lg. | Wd. | Dp. | Handle Lg. | Manufacturer Model No. | Features | Each | |
| Parker 43 Parker 43 Parker 43 Parker 43 Parker 56 Parker 56 | Parker 302 Parker 422 Parker 487 Parker 777 Parker 510D Parker 518D | 1" 1" 3/4" 5/8" 1" 1" | 15" | 13" | 6" | 23" | 94C-001-PFD | Carrying Handle | 0000000 | 000000000 |
Air Inlet | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Hose Fitting Manufacturer Series | For Hose Manufacturer Series | For Maximum Hose ID | Lg. | Wd. | Dp. | Flared Angle | Thread Size  | Thread Type | Gender | Manufacturer Model No. | Features | Each | |
| Parker 43 Parker 43 Parker 43 Parker 43 Parker 56 Parker 56 | Parker 302 Parker 422 Parker 487 Parker 777 Parker 510D Parker 518D | 1" 1" 3/4" 5/8" 1" 1" | 15" | 12" | 6" | 37° | 9/16"-18 | UN/UNF (JIC) | Male | 94C-002-PFD | Carrying Handle | 0000000 | 000000000 |
For Parker 43 Series Fittings | For Parker 56 Series Fittings | ||||||
|---|---|---|---|---|---|---|---|
| For Hose ID | For Dash Size | Material | Color | Each | Each | ||
| 1/8" | 02 | Steel | Brown | 000000 | 00 | 0000000 | 0000000 |
| 1/4" | 04 | Steel | Red | 0000000 | 0000000 | 0000000 | 000000 |
| 3/8" | 06 | Steel | Yellow | 0000000 | 000000 | 0000000 | 000000 |
| 1/2" | 08 | Steel | Blue | 0000000 | 000000 | 0000000 | 000000 |
| 5/8" | 10 | Steel | Orange | 0000000 | 000000 | 0000000 | 000000 |
| 3/4" | 12 | Steel | Green | 0000000 | 000000 | 0000000 | 000000 |
| 1" | 16 | Steel | Black | 0000000 | 000000 | 0000000 | 000000 |
Hose Crimping Tool and Fitting Sets for Compressed Gas
Sets contain a crimping tool and a variety of fittings, nuts, and ferrules so you can connect pressure regulators, torches, and other components of your welding system. Fittings are also known as CGA (Compressed Gas Association) fittings. They are brass for good corrosion resistance.
Barbed adapters let you adapt to a threaded end so you can connect welding hose to pressure regulators or torches. They consist of a barbed shaft with a rounded end that sits inside a threaded nut so you can make a threaded hose connection.
Barbed connectors are also known as hose menders and splicers. Use them to connect lengths of hose or to repair damaged hose. Slide the barbed end into welding hose and use a hose ferrule and the crimping tool to secure the fitting to hose.
Threaded connectors let you attach threaded welding hose to pressure regulators and torches.
Fittings with left-hand threads are identified with a notch in the nut.
Note: Fittings have a CGA number that corresponds to a specific type of gas. Choose a fitting with the same CGA number as your tank and other system components.
| For Hose ID | No. of Pieces | Includes | Max. Pressure | For Use With | Each | |
Brass | ||||||
|---|---|---|---|---|---|---|
| 3/16", 1/4" | 93 | Crimping Tool Eight barbed hose adapters for 3/16" hose ID (use with A-size nuts) Six barbed hose adapters for 3/16" hose ID (use with B-size nuts) Ten barbed hose adapters for 1/4" hose ID (use with B-size nuts) Two barbed hose connectors for 3/16" hose ID Four barbed hose connectors for 1/4" hose ID One A-size 3/8"-24 male right-hand threaded connector (CGA-020) One A-size 3/8"-24 male left-hand threaded connector (CGA-021) One B-size 9/16"-18 male right-hand threaded connector (CGA-022) One B-size 9/16"-18 male left-hand threaded connector (CGA-023) Four A-size 3/8"-24 right-hand threaded nuts (CGA-020) Four A-size 3/8"-24 left-hand threaded nuts (CGA-021) Eight B-size 9/16"-18 female right-hand threaded nuts (CGA-022) Eight B-size 9/16"-18 female left-hand threaded nuts (CGA-023) Twelve ferrules with 0.45" hose end ID Ten ferrules with 0.562" hose end ID Twelve ferrules with 0.593" hose end ID | 200 psi @ 72° F | Acetylene, Butane, Fuel Gases, LP Gas, Natural Gas, Oxygen, Propane | 0000000 | 0000000 |
| 5/16", 3/8" | 71 | Crimping Tool Eight barbed hose adapters for 5/16" hose ID (use with B-size nuts) Eight barbed hose adapters for 3/8" hose ID (use with B-size nuts) Two barbed hose connectors for 5/16" hose ID Two barbed hose connectors for 3/8" hose ID One B-size 9/16"-18 male right-hand threaded connector (CGA-022) One B-size 9/16"-18 male left-hand threaded connector (CGA-023) Eight B-size 9/16"-18 female right-hand threaded nuts (CGA-022) Eight B-size 9/16"-18 female left-hand threaded nuts (CGA-023) Eight ferrules with 0.625" hose end ID Eight ferrules with 0.656" hose end ID Six ferrules with 0.687" hose end ID Eight ferrules with 0.718" hose end ID | 200 psi @ 72° F | Acetylene, Butane, Fuel Gases, LP Gas, Natural Gas, Oxygen, Propane | 0000000 | 000000 |
Hammer-Operated Crimpers
Use a hammer strike or a vise to crimp ferrules onto your hose and secure barbed hose fittings.
| For Use With | For Hose OD | Lg. | Wd. | Material | Number of Jaw Holes | Each | |
| Air Hose, Water Hose | 7/16", 9/16", 11/16" | 9 1/8" | 1" | Steel | 3 | 0000000 | 000000 |
Hose-Crimping Pliers
As you squeeze the handles, the vise-like jaws lock tightly onto the ferrule to secure barbed fittings onto your hose. To select the correct pliers, measure the hose OD and select the next larger size "For Hose OD" below.
Lever-Operated Crimpers with Dies
Crimpers are furnished with five removable dies that crimp air and water hose. Place your hose, ferrule, and barbed fitting into a die that's inserted in the crimper. Press the lever to crimp the fitting onto the hose. Fasteners not included. Hose OD compatibility is measured without the fittings installed.
Individual dies (sold separately) allow you to crimp sizes of air and water hose from 0.385" to 0.843" OD.
Lever-Operated Crimpers
Place your hose, ferrule, and barbed fitting into a die that's inserted in the crimper. Press the lever to crimp the fitting onto the hose. Use with aluminum or brass ferrules. Fasteners not included.
Individual dies (sold separately) allow you to crimp large sizes of air and water hose from 3/4" to 1 3/8" OD (measured without the fittings installed).
Mounting Holes | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Use With | For Hose OD | Lg. | Base Material | Handle Material | Number of | Dia. | Each | |
| Air Hose, Water Hose | 3/4" to 1 3/8" | 12" | Iron | Zinc-Plated Steel | 2 | 1/8" | 000000 | 0000000 |
| Dies for 0.906" Hose OD | 0000000 | Each | 000000 |
| Dies for 0.813" Hose OD | 0000000 | Each | 00000 |
| Dies for 3/4" Hose OD | 0000000 | Each | 00000 |
| Dies for 1" Hose OD | 0000000 | Each | 00000 |
| Dies for 1 3/8" Hose OD | 0000000 | Each | 00000 |
| Dies for 7/8" Hose OD | 0000000 | Each | 00000 |
| Dies for 0.969" Hose OD | 0000000 | Each | 00000 |
| Dies for 0.938" Hose OD | 0000000 | Each | 00000 |
| Dies for 0.781" Hose OD | 0000000 | Each | 00000 |
| Dies for 1 1/8" Hose OD | 0000000 | Each | 00000 |