McMaster-Carr logo
    Filter by
    System of Measurement
    Bearing Seal Type
    Bearing Type
    Industrial Info Compare
    Bearing Material
    Number of Set Screws Included
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Cage Material
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    133 Products

    Insert Bearings

    Image of ProductInUse. Install by hand into a housing (sold separately). Front orientation. Ball Bearings. Insert Bearings.

    Install by hand into a housing (sold

    separately)

    Image of Product. Front orientation. Ball Bearings. Insert Bearings.
    Swap out worn inserts instead of replacing the entire mounted unit. To choose an insert, match the manufacturer model number on your existing bearing.
    Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place, regardless of the direction the shaft spins.
    Eccentric-Lock Shaft Mount—Twist the collar one way to tighten these bearings and the other way to loosen. They're a good choice when you need to take your setup apart frequently. However, they only turn one way, so they won't work with shafts that reverse.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Temp.
    Range, ° F
    For Shaft
    Dia.
    For Mounted Bearing Model No.
    Bearing
    Material
    ABEC
    Rating
    Min.
    Max.
    Each
    For SKF Mounted Bearings
     
    Set-Screw Shaft Mount
    1/2"F2B 008-RM, FYT 1/2 RMSteel-202100000000000000
    3/4"F2B 012-RM, F4B 012-RM, FYT 3/4 RMSteel-20210000000000000
    1"F2B 100-RM, F4B 100-RM, FYT 1. RMSteel-20210000000000000
    1 1/8"F2B 102 TF, F4B 102-TF, FY 1.1/8 TF, FYT 1.1/8 TFSteel-20210000000000000
    1 3/16"F2B 103-RM, F4B 103-RM, FYT 1.3/16 RMSteel-20210000000000000
    1 1/4"F2B 104-RM, F4B 104-RM, FYT 1.1/4 RMSteel-20210000000000000
    1 1/4"F2B 104S-RM, F4B 104S-RMSteel-20210000000000000
    1 3/8"F4B 106-TF, FY 1.3/8 TF, FYT 1.3/8 TFSteel-20210000000000000
    1 7/16"F2B 107-RM, F4B 107-RM, FYT 1.7/16 RMSteel-20210000000000000
    1 1/2"F2B 108-TF, F4B 108-TF, FYT 1.1/2 RMSteel-202100000000000000
    1 3/4"F2B 112-RM, F4B 112-RM, FYT 1.3/4 RMSteel-202100000000000000
    1 15/16"F2B 115-TF, F4B 115-TF, FYT 1.15/16 RMSteel-202100000000000000
    2"F2B 200-RM, F4B 200-RM, FYT 2. RMSteel-202100000000000000
    2 1/4"F4B 204-TF, FY 2.1/4 TF, FYT 2.1/4 TFSteel-202100000000000000
    2 1/2"F4B 208-TF, FY 2.1/2 TF, FYT 2.1/2 TFSteel-202100000000000000
     
    Eccentric-Lock Shaft Mount
    5/8"P2BL 010-FM, SYH 5/8 FMSteel-202100000000000000
    3/4"P2BL 012-FM, SYH 3/4 FMSteel-202100000000000000
    7/8"P2BL 014-FM, SYH 7/8 FMSteel-202100000000000000
    1"P2BL 100-FM, SYH 1. FMSteel-202100000000000000
    1 1/4"P2BL 104-FM, SYH 1.1/4 FMSteel-202100000000000000
    1 1/4"SYH 1.1/4 AFMSteel-202100000000000000
    1 3/8"P2BL 106-FM, SYH 1.3/8 FMSteel-202100000000000000
    1 7/16"P2BL 107-FM, SYH 1.7/16 FMSteel-202100000000000000
    1 1/2"P2BL 108-WF, SYH 1.1/2 WFSteel-202100000000000000
    1 15/16"P2BL 115-WF, SYH 1.15/16 WFSteel-2021000000000000000
    2"P2BL 200-FM, SYH 2. FMSteel-2021000000000000000
    2 3/16"SYH 2.3/16 FMSteel-2021000000000000000
     
    For Sealmaster Mounted Bearings
     
    Set-Screw Shaft Mount
    5/8"FB-10, NP-10, NPL-10, SC-10, SF-10, SFT-10, ST-10, TB-10Steel1-202200000000000000
    3/4"FB-12, NP-12, NPL-12, SC-12, SF-12, SFT-12, ST-12, TB-12Steel1-202200000000000000
    7/8"FB-14, NP-14, NPG-14-6, NPG-14-9, NPL-14, SC-14, SF-14, SFT-14, SP-14, ST-14, STH-14-6, STH-14-9, TB-14Steel1-2022000000000000000
    1"FB-16, NP-16, NPG-16-6, NPG-16-9, NPL-16, SC-16, SF-16, SFT-16, SP-16, ST-16, STH-16-6, STH-16-9, TB-16Steel1-2022000000000000000
    1"FB-16-HT, NP-16-HT, NPG-16-6-HT, NPG-16-9-HT, NPL-16-HT, SC-16-HT, SF-16-HT, SFT-16-HT, SP-16-HT, ST-16-HT, STH-16-6-HT, STH-16-9-HT, TB-16-HTSteel1-2040000000000000000
    1 1/8"FB-18, NP-18, NPG-18-6, NPG-18-9, NPL-18, SC-18, SCHB-18, SEHB-18, SF-18, SFC-18, SFT-18, SP-18, ST-18, STH-18-6, STH-18-9, TB-18Steel1-2022000000000000000
    1 3/16"FB-19, NP-19, NPG-19-6, NPG-19-9, NPL-19, SC-19, SF-19, SFC-19, SFT-19, SP-19, ST-19, STH-19-6, STH-19-9, TB-19Steel1-2022000000000000000
    1 1/4"FB-20, NP-20, NPG-20-12, NPG-20-9, NPL-20, SC-20, SCHB-20, SEHB-20, SF-20, SFC-20, SFT-20, SP-20, ST-20, STH-20-12, STH-20-9, TB-20Steel1-2022000000000000000
    1 1/4"FB-20-HT, NP-20-HT, NPG-20-12-HT, NPG-20-9-HT, NPL-20-HT, SC-20-HT, SCHB-20-HT, SEHB-20-HT, SF-20-HT, SFC-20-HT, SFT-20-HT, SP-20-HT, ST-20-HT, STH-20-12-HT, STH-20-9-HT, TB-20-HTSteel1-2040000000000000000
    1 1/4"FB-20R, NP-20R, NPL-20R, SC-20R, SF-20R, SFC-20R, SFT-20R, SP-20R, ST-20R, TB-20RSteel1-2022000000000000000
    1 3/8"FB-22, NP-22, NPG-22-12, NPG-22-9, NPL-22, SC-22, SCHB-22, SEHB-22, SF-22, SFC-22, SFT-22, SP-22, ST-22, STH-22-12, STH-22-9, TB-22Steel1-2022000000000000000
    1 7/16"FB-23, NP-23, NPG-23-12, NPG-23-9, NPL-23, SC-23, SF-23, SFC-23, SFT-24, SP-23, ST-23, STH-23-12, STH-23-9, TB-23Steel1-2022000000000000000
    1 1/2"NP-24, NPG-24-12, NPG-24-18, NPL-24, SC-24, SCHB-24, SEHB-24, SF-24, SFC-24, SFT-24, SP-24, ST-24, STH-24-12, STH-24-18, TB-24Steel1-2022000000000000000
    1 11/16"NP-27, NPG-27-12, NPG-27-18, NPL-27, SC-27, SF-27, SFC-27, SFT-27, SP-27, ST-27, STH-27-12, STH-27-18, TB-27Steel1-2022000000000000000
    1 3/4"NP-28, NPL-28, SC-28, SFC-28, SFT-28, SP-28, ST-28, TB-28Steel1-2022000000000000000
    1 15/16"FB-31, NP-31, NPG-31-12, NPG-31-18, NPL-32, SC-31, SCHB-31, SEHB-31, SF-31, SFC-31, SFT-31, SP-31, ST-31, STH-31-12, STH-31-18, TB-31Steel1-2022000000000000000
    2"NP-32, NPG-32-12, NPG-32-18, NPL-32, SC-32, SF-32, SFC-32, SFT-32, SP-32, ST-32, STH-32-12, STH-32-18Steel1-2022000000000000000
    2 3/16"NP-35, NPG-35-12, NPG-35-18, NPL-35, SC-35, SF-35, SFC-35, SFT-35, SP-35, ST-35, STH-35-12, STH-35-18Steel1-2022000000000000000
    2 7/16"NP-39, NPG-39-12, NPG-39-18, NPL-39, SC-39, SCHB-39, SEHB-39, SF-39, SFC-39, SP-39, ST-39, STH-39-12, STH-39-18Steel1-2022000000000000000
    20 mmFB-204, NP-204, NPL-204, SC-204, SF-204, SFT-204, ST-204, TB-204Steel1-2022000000000000000
    25 mmFB-205, NP-205, NPG-205-6, NPG-205-9, NPL-205, SC-205, SF-205, SFT-205, SP-205, ST-205, STH-205-6, STH-205-9, TB-205Steel1-2022000000000000000
    30 mmFB-206, NP-206, NPG-206-6, NPG-206-9, NPL-206, SC-206, SCHB-206, SEHB-206, SF-206, SFC-206, SFT-206, SP-206, ST-206, STH-206-6, STH-206-9, TB-206Steel1-2022000000000000000
    35 mmFB-207, NP-207, NPG-207-12, NPG-207-9, NPL-207, SC-207, SCHB-207, SEHB-207, SF-207, SFC-207, SFT-207, SP-207, ST-207, STH-207-12, STH-207-9, TB-207Steel1-2022000000000000000
    40 mmNP-208, NPG-28-18, NPG-208-12, NPL-208, SC-208, SCHB-208, SEHB-208, SF-208, SFC-208, SFT-208, SP-208, ST-208, STH-208-12, STH-208-18, TB-208Steel1-2022000000000000000
    50 mmFB-210, NP-210, NPG-210-12, NPG-210-18, NPL-210, SC-210, SCHB-210, SEHB-210, SF-210, SFC-210, SFT-210, SP-210, ST-210, STH-210-12, STH-210-18, TB-210Steel1-2022000000000000000
     
    For Timken Mounted Bearings
     
    Set-Screw Shaft Mount
    1/2"SAK 1/2, SAS 1/2, SCJ 1/2, SCJT 1/2Steel1-65250000000000000
    5/8"SAK 5/8, SAS 5/8, SCJ 5/8, SCJT 5/8Steel1-65250000000000000
    3/4"SAK 3/4, SAS 3/4, SCJ 3/4, SCJT 3/4, STB 3/4Steel1-65250000000000000
    1"SAK 1, SAS 1, SCJ 1, SCJT 1, STB 1Steel1-65250000000000000
    1 3/16"SAK 1 3/16, SAS 1 3/16, SCJ 1 3/16, SCJT 1 3/16, STB 1 3/16Steel1-65250000000000000
    1 1/4"SAK 1 1/4, SAS 1 1/4, SCJ 1 1/4, SCJT 1 1/4, STB 1 1/4Steel1-65250000000000000
    1 1/4"SAK 1 1/4 S, SAS 1 1/4 S, SCJ 1 1/4 S, STB 1 1/4 SSteel1-65250000000000000
    1 7/16"SAK 1 7/16, SAS 1 7/16, SCJ 1 7/16, SCJT 1 7/16, STB 1 7/16Steel1-65250000000000000
    1 1/2"SAK 1 1/2, SAS 1 1/2, SAS 1 1/2 H, SCJ 1 1/2, SCJT 1 1/2, STB 1 1/2Steel1-652500000000000000
    1 5/8"SAK 1 5/8, SAS 1 5/8, SCJ 1 5/8, SCJT 1 5/8, STB 1 5/8Steel1-652500000000000000
    1 11/16"SAK 1 11/16, SAS 1 11/16, SCJ 1 11/16, SCJT 1 11/16, STB 1 11/16Steel1-652500000000000000
    1 3/4"SAK 1 3/4, SAS 1 3/4, SCJ 1 3/4, SCJT 1 3/4, STB 1 3/4Steel1-652500000000000000
    2"SAK 2 S, SAS 2 S, SCJ 2 S, SCJT 2 SSteel1-652500000000000000
    25 mmSAK 25, SAS 25, SCJ 25, SCJT 25, STB 25Steel1-65250000000000000
    30 mmSAK 30, SAS 30, SCJ 30, SCJT 30, STB 30Steel1-65250000000000000
    35 mmSAK 35, SAS 35, SCJ 35, SCJT 35, STB 35Steel1-65250000000000000
     

    Quick-Mount Ball Bearings

    Image of Product. Front orientation. Ball Bearings. Quick-Mount Ball Bearings, Set-Screw Shaft Mount.

    Set-Screw

    Shaft Mount

    Slip onto a shaft and secure with the turn of a screw. You don't need any special tools to mount these bearings.
    Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place. For high-speed applications, consider clamp-on shaft mounts, which are less likely to slip.
    Steel and Black-Oxide Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.
    Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Retaining
    Ring
    Temp.
    Range, ° F
    For Shaft
    Dia.
    For Housing
    ID
    Wd.
    OD
    Thk.
    Bearing Seal
    Type
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Bearing Trade
    No.
    Each
    Set-Screw Shaft Mount
     
    Steel
    1/2"1 3/4"5/8"1.922"0.042"SealedNot Rated2,5505,000-202507608-2RS0000000000000
    9/16"1 3/4"5/8"1.922"0.042"SealedNot Rated2,5505,000-202507609-2RS000000000000
    5/8"1 3/4"5/8"1.922"0.042"SealedNot Rated2,5505,000-202507610-2RS00000000000
    11/16"1 3/4"5/8"1.922"0.042"SealedNot Rated2,5505,000-202507611-2RS000000000000
    3/4"1 3/4"5/8"1.922"0.042"SealedNot Rated2,5505,000-202507612-2RS00000000000
    13/16"2"5/8"2.156"0.042"SealedNot Rated2,9505,000-202507613-2RS000000000000
    7/8"2"5/8"2.156"0.042"SealedNot Rated2,9505,000-202507614-2RS000000000000
    15/16"2"5/8"2.156"0.042"SealedNot Rated2,9505,000-202507615-2RS000000000000
    1"2"5/8"2.156"0.042"SealedNot Rated2,9505,000-202507616-2RS00000000000
    1 1/16"2 9/16"3/4"2.766"0.065"SealedNot Rated5,3505,000-202507617-2RS000000000000
    1 1/8"2 9/16"3/4"2.766"0.065"SealedNot Rated5,3505,000-202507618-2RS000000000000
    1 1/4"2 9/16"3/4"2.766"0.065"SealedNot Rated5,3505,000-202507620-2RS000000000000
     
    Black-Oxide Steel
    1/2"1 27/32"5/8"2.063"0.047"Shielded13,2009,200-40250ER8
    000000000000
    5/8"1 27/32"5/8"2.063"0.047"SealedNot Rated2,8505,000-20250ER10
    000000000000
    3/4"1 27/32"5/8"2.063"0.047"SealedNot Rated2,8505,000-20250ER12
    000000000000
    7/8"2 3/64"3/4"2.266"0.047"Shielded13,4507,800-40250ER14
    000000000000
    15/16"2 3/64"3/4"2.266"0.047"Sealed12,8006,350-20220ER15
    0000000000000
    1"2 3/64"3/4"2.266"0.047"SealedNot Rated3,1005,000-20250ER16
    000000000000
    1 1/16"2 7/16"7/8"2.656"0.063"Sealed14,3505,450-20220ER17
    0000000000000
    1 1/8"2 7/16"7/8"2.656"0.063"Sealed14,8506,100-65250ER18
    000000000000
    1 3/16"2 7/16"7/8"2.656"0.063"SealedNot Rated4,3505,000-20250ER19
    000000000000
    1 1/4"2 27/32"15/16"3.078"0.063"SealedNot Rated5,7505,000-20250ER20
    000000000000
    1 3/8"2 27/32"15/16"3.078"0.063"Shielded16,4005,000-40250ER22
    0000000000000
    1 7/16"2 27/32"15/16"3.078"0.063"SealedNot Rated5,7505,000-20250ER23
    000000000000
    1 1/2"3 5/32"1 3/32"3.406"0.063"SealedNot Rated6,5005,000-20250ER24
    0000000000000
    1 5/8"3 11/32"1 3/32"3 19/32"0.063"Sealed17,9003,800-20220ER26
    0000000000000
    1 11/16"3 11/32"1 3/32"3 19/32"0.063"Sealed17,9003,800-20220ER27
    0000000000000
    1 3/4"3 11/32"1 3/32"3.578"0.063"Shielded18,1503,900-40250ER28
    0000000000000
    1 15/16"3 35/64"1 1/8"3.781"0.094"SealedNot Rated7,9005,000-20250ER31
    0000000000000
    2"3 15/16"1 3/16"4.188"0.094"Shielded110,8003,400-40250ER32
    0000000000000
    2 3/16"3 15/16"1 3/16"4 3/16"0.094"Sealed19,7503,250-20220ER35
    0000000000000
    2 1/4"4 21/64"1 1/4"4 37/64"0.094"Sealed111,7503,000-20220ER36
    0000000000000
    2 3/8"4 21/64"1 1/4"4 37/64"0.094"Sealed111,7503,000-20220ER38
    0000000000000
    2 7/16"4 21/64"1 1/4"4 37/64"0.094"Sealed111,7503,000-20220ER39
    0000000000000
    2 1/2"4 59/64"1 3/8"5 9/32"0.109"Sealed113,9502,500-20220ER40
    0000000000000
    3"5 33/64"1 11/16"5 13/16"0.109"Sealed117,4002,250-20220ER48
    0000000000000
    20 mm47 mm15.9 mm52.4 mm1.2 mmSealed12,6007,300-20220ER204
    000000000000
    25 mm52 mm19.1 mm57.5 mm1.2 mmSealed12,8006,350-20220ER205
    0000000000000
    30 mm62 mm22.2 mm67.5 mm1.6 mmSealed14,3505,450-20220ER206
    0000000000000
    35 mm72 mm23.8 mm78.2 mm1.6 mmSealed15,7504,650-20220ER207
    0000000000000
    40 mm80 mm27.8 mm86.5 mm1.6 mmSealed17,3004,150-20220ER208
    0000000000000
    50 mm90 mm28.6 mm96 mm2.4 mmSealed17,8503,550-20220ER210
    0000000000000
    70 mm125 mm34.9 mm134.1 mm2.8 mmSealed113,9502,500-20220ER214
    0000000000000
     

    Dry-Running Insert Bearings

    Image of ProductInUse. Install by hand into a housing (sold separately). Front orientation. Sleeve Bearings. Dry-Running Insert Bearings.
    Image of Product. Front orientation. Sleeve Bearings. Dry-Running Insert Bearings.

    Install by hand into a housing (sold

    separately)

    Replace your ball bearing insert with plastic inserts that don't require lubrication. They’re tough, wear resistant, and won't absorb water in wet and humid environments. Use the bearing housing number on your existing mounted bearing to choose a compatible insert. You'll be able to install them into a metal pillow block or flanged housing bearing by hand.
    For Shaft
    Dia.
    For Mounted Bearing
    Model No.
    Temp. Range,
    ° F
    Each
    Plastic Blend
    1"UCF205, UCFL205, UCP205-55 to 1900000000000000
    1 1/2"UCF208, UCFL208, UCP208-55 to 190000000000000
    2"UCF211, UCFL211, UCP211-55 to 190000000000000
    17 mmUCF203, UCFL203, UCP203-55 to 190000000000000
    20 mmPF204, PFL204, PP204-55 to 19000000000000
    20 mmUCF204, UCFL204, UCP204-55 to 190000000000000
    25 mmPF205, PFL205, PP205-55 to 19000000000000
    25 mmUCF205, UCFL205, UCP205-55 to 190000000000000
    30 mmPF206, PFL206, PP206-55 to 19000000000000
    30 mmUCF206, UCFL206, UCP206-55 to 190000000000000
    35 mmUCF207, UCFL207, UCP207-55 to 190000000000000
    40 mmUCF208, UCFL208, UCP208-55 to 190000000000000
    45 mmUCF209, UCFL209, UCP209-55 to 190000000000000
    50 mmUCF210, UCFL210, UCP210-55 to 190000000000000
     

    Quick-Mount Ball Bearings for Food and Beverage

    Image of Product. Front orientation. Ball Bearings. Quick-Mount Ball Bearings for Food and Beverage, Set-Screw Shaft Mount.

    Set-Screw Shaft

    Mount

    You don't need any special tools to install these bearings in food production areas. Slip them onto a shaft and secure with the turn of a screw for easy mounting. Greased with NSF-registered H1 lubricant, these bearings are safe to install on food-processing equipment, such as conveyor belts, so long as they don’t directly touch the food. They're IP69K rated, so they'll stand up to the hot water from a pressure washer when cleaning your facility at the end of the day.
    Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place. For high-speed applications, consider clamp-on shaft mounts, which are less likely to slip.
    Corrosion-Resistant Nickel-Plated Steel—These bearings resist mild chemicals, such as the ammonia in cleaning solutions, while maintaining the strength of steel. The nickel coating can wear or chip over time, though. If it does, the steel beneath will rust quickly.
    Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Retaining
    Ring
    Temp.
    Range, ° F
    For Shaft
    Dia.
    For Housing
    ID
    Wd.
    OD
    Thk.
    Bearing
    Seal Type
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Enclosure
    Rating
    Food Industry
    Std.
    Each
    Set-Screw Shaft Mount
     
    Corrosion-Resistant Nickel-Plated Steel
    1"2 3/64"3/4"2.266"0.047"Sealed12,8002,700-20220IP69K
    NSF Registered H1
    00000000000000
    1 1/4"2 7/16"7/8"2.656"0.063"Sealed14,3502,000-20220IP69K
    NSF Registered H1
    0000000000000
    1 3/8"2 55/64"15/16"3.078"0.063"Sealed15,7502,000-20220IP69K
    NSF Registered H1
    0000000000000
    1 7/16"2 27/32"15/16"3.078"0.063"Sealed15,7502,000-20220IP69K
    NSF Registered H1
    0000000000000
    1 1/2"3 5/32"1 3/32"3.406"0.063"Sealed17,3001,750-20220IP69K
    NSF Registered H1
    0000000000000
    1 3/4"3 11/32"1 3/32"3.594"0.063"Sealed17,9001,600-20220IP69K
    NSF Registered H1
    0000000000000
    2"3 15/16"1 3/16"4.188"0.094"Sealed19,7501,350-20220IP69K
    NSF Registered H1
    0000000000000
    2 3/16"3 15/16"1 3/16"4.188"0.094"Sealed19,7501,350-20220IP69K
    NSF Registered H1
    0000000000000
     
    back to top