The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

Install these inserts into plastic parts to create a secure base for fasteners.

Made from brass, these inserts are electrically conductive, nonmagnetic, and have good corrosion resistance.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.

These 18-8 stainless steel inserts have better corrosion resistance than aluminum inserts and may be mildly magnetic.

The barbed sides keep these securely in place even before a screw is installed.

Made of 18-8 stainless steel, these inserts have good corrosion resistance.

Forming the strongest hold of any of our threaded inserts, these inserts have a distorted internal thread to lock screws into place and keys that drive into surrounding material to prevent slipping and rotating.

A dry film keeps the screw from sticking or binding in these inserts during installation.

These inserts have a high strength-to-weight ratio and resist acids and salt water better than nickel alloy and stainless steel inserts.

A distorted thread grips the screw to resist loosening.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

A dry film keeps the screw from sticking or binding in these inserts during installation.

Inserts come with a through-hole tap and installation tool.

A black-phosphate finish provides mild corrosion resistance.

These inserts are the most corrosion-resistant thread-locking inserts we offer.

A closed-end tap, drill bit, and installation bit are included with these inserts.

The flange keeps these inserts from being pulled through a hole and provides a load bearing surface.

Assortments include various sizes of tapping inserts for softwood.

These 18-8 stainless steel inserts have excellent resistance to chemicals and may be mildly magnetic.

Steel inserts have high strength for durability.

Fewer prongs than other tee nut inserts reduce the risk of splitting hardwood—these inserts have three short prongs.

Six prongs around the barrel of these inserts provide a strong hold and prevent them from loosening and twisting.

A closed end seals out elements and protects the threads on these inserts from debris.

Also known as clinch style captive nuts, press these nuts into a drilled or punched hole with an arbor press or similar pressure tool.

A flat hex head sits flush against the material surface for use in low-clearance applications.

Stainless steel press-fit nuts have excellent corrosion resistance in most environments.

Also known as broach style captive nuts, these nuts have good chemical resistance and may be mildly magnetic.

About twice as strong as aluminum rivet nuts, these steel rivet nuts are zinc plated for mild corrosion resistance.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

Wedges under the flange lock the nut in place in soft materials such as brass and aluminum.

These kits include one size of low-profile rivet nuts.

The most corrosion resistant low-profile rivet nuts we offer, these stand up to chemicals.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

A PVC foam seal under the flange keeps liquids and gasses from leaking between the nut and the surrounding material.

A nonconductive rubber coating insulates the nut from electricity, seals out moisture, and damps vibration.

A smooth base provides more contact with the mating surface than weld nuts with projections.

Projections on the base concentrate the weld and provide room for heat to dissipate.

A smooth base provides more contact with the mating surface than weld nuts with projections.

Weld these nuts to stainless steel surfaces.

Weld these nuts to uncoated steel surfaces.

You can weld these nuts to flat and uneven uncoated stainless steel surfaces for a strong permanent hold.

Threads float inside the retainer so you can install a bolt at a slight angle to align with off center parts.

Stainless steel adhesive-mount nuts have excellent corrosion resistance in most environments.

Stainless steel nuts have excellent corrosion resistance in most environments.

Snap these nuts into square holes in thin materials.

About half the strength of medium-strength steel coupling nuts, these metric nuts are for light duty fastening applications.

18-8 stainless steel studs have good chemical resistance.

Screw these studs into a tapped hole and use them as a pivot point, hinge, shaft, or locator pin.

Add a stud to thin material when you only have access to one side.

These steel studs are zinc plated to resist corrosion in wet environments.

These studs have good chemical resistance. Weld them to stainless steel surfaces.

Brass binding barrels and screws are corrosion resistant in wet environments and electrically conductive.

Install these inserts into a compatible holder to cut external or internal threads on a workpiece.

These tools come with one high-speed steel insert for use on steel and stainless steel and one high-speed steel insert for use on softer materials, such as aluminum and brass. When one point of an insert dulls, rotate it to use a sharp point.

Solid carbide provides more rigidity than carbide-tipped tools.

The carbide tip brazed onto the ground steel shanks of these tools is more wear resistant than high-speed steel.

Cut threads in plastic and most metal with these high-speed steel tools.

Seal tube and hose fittings to keep their straight threads protected from contaminants during fabrication and storage.

Protect externally threaded components from contaminants during fabrication and storage.