We will reply to your message within an hour.
Soft and easy to install, this insulation restricts absorption of water, air, and gas. It is often used on cold and hot water lines and refrigeration lines.
Even at high temperatures, these tubes remain flexible to stretch over components without tearing. They restrict absorption of water, air, and gas and are typically used on hot and cold water lines and electrical components.
Less flexible than rubber foam, this insulation restricts absorption of water, air, and gas. It is typically used in plumbing applications
This common insulation material is typically used on hot and cold water lines and in process piping.
These rigid, lightweight melamine foam tubes are wrapped in an ISO Class 5 and Fed. Spec. Class 100 clean room jacket that is suitable for sanitary and washdown applications. They’re typically used on cold and hot water piping and with refrigeration systems.
Hook-and-loop fasteners make it easy to install, remove, and reuse this flexible insulation. Use on steam, hot water, and process pipes and fittings.
Shield against extreme heat with these flexible ceramic strips. They are often used to insulate hose, cables, and process piping.
Melamine has a lightweight construction that allows quick and easy installation. Use on cold and hot water piping and with refrigeration systems.
Rigid and flame resistant, these insulation tubes are typically used in process piping and mechanical systems.
Lightweight and super thin, these fiber-reinforced silica aerogel sheets and strips flex into tight spaces other insulation can't. Use on process piping and in power-generating applications.
These kits insulate one P-trap and two stop valves to reduce the risk of burns from accidental contact with hot pipes under your sink. The molded, flexible pipe covers are ADA compliant when properly installed.
Superior in strength and durability, these thin strips insulate as well as protect personnel from accidental contact with hot pipes. Use for exhaust, hot water, and process pipes.
Reduce the risk of burns from accidental contact with hot pipes under your sink. These molded, flexible pipe covers are ADA compliant when properly installed.
Very rigid with a 0% water absorption rate, this insulation is unaffected by corrosive environments, organic solvents, and most acids. It is typically used in chemical-processing systems and underground lines.
This very rigid insulation offers the lowest heat-flow rate of our pipe insulation and restricts absorption of water, air, and gas. It is typically used in process piping and chiller plants and performs best in applications below 50° F.
Able to withstand temperatures as low as -290° F, these super-thin, lightweight sheets are made of fiber-reinforced silica aerogel that can flex into tight spaces other insulation can't. Use in process piping and power-generating applications.
Save installation time with banding that’s ready to use. It has an easy-to-close fastener on one end.
Protect insulation from light impact and moisture with this durable PVC jacketing.
Guard insulation from heavy impact and chemical exposure. This metal jacketing is corrosion resistant and often used outdoors.
Wrap pipes, tubing, and fittings to prevent condensation from forming. These strips are for use on copper, iron, and steel.
Prevent condensation from forming on refrigeration and air conditioning lines and cold‐water piping.
Protect and repair insulation with this cotton fiber and resin mesh.
An alternative to jacketing, these coatings create a vapor barrier and protect from conditions outdoors. They are often used on irregularly shaped surfaces, such as fittings, flanges, and valves.
This sleeving withstands temperatures up to 390°F and is often used to insulate connections in transformers and relays. It prevents electricity and heat from dissipating from wire and cable.
Add a layer of insulation to prevent electricity and heat from dissipating from wire and cable.
A specially formulated silicone rubber coating allows this sleeving to stretch over items during installation; it then tightens around its contents for a secure fit.
Use this PTFE sleeving in applications where temperatures reach up to 500° F.
Made from thicker and denser fiberglass than standard spark-resistant sleeving, this sleeving is more abrasion resistant and provides better insulation. The silicone rubber coating protects against sparks and molten metal splash.
A silicone rubber coating on this fiberglass sleeving protects against sparks and molten metal splash.
This sleeving withstands temperatures over 1000°F, such as in refineries.
Unlike fiberglass and silica, this sleeving won't irritate skin, so it's easier to handle. It has a temperature rating of 1100° F or higher.
With a temperature rating of 1800°F or higher, this sleeving can withstand hotter temperatures than fiberglass and most ceramic.
A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F
Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.
Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.
This sleeving reflects heat away from contents and withstands temperatures up to 300°F. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.
This sleeving reflects heat away from contents and withstands temperatures up to 900°F. The corrugated construction gives it impact and abrasion resistance similar to conduit, but with more flexibility.
Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.
Silicone rubber coats this fiberglass sleeving to shed sparks and molten metal splash. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.
Use this general purpose tubing to insulate and protect wire and cable.
Extra-thick walls provide more protection against abrasion and tears than standard high-shrink-ratio tubing. This tubing shrinks down to 1/6th of its original ID, so it creates a tight seal over irregularly shaped objects.
This tubing creates a tight seal over irregularly shaped objects.
Identify ground wire with this green-and-yellow striped tubing.
Access connections more easily than with standard heat-shrink tubing. Make a small slit in this tubing to peel it away.
The smallest heat-shrink tubing we offer, this tubing protects wire with a 0.017" and smaller diameter.
With thin walls, this tubing shrinks faster than other high-temperature tubing. It withstands up to 500° F.
Use this tubing in applications where temperatures reach up to 500° F. It's often used to insulate electronic components.
This tubing shrinks down to a quarter of its original ID, so it creates a tight seal over irregularly shaped objects. It withstands up to 500° F.
Also known as halogen-free tubing, this tubing produces minimal amounts of smoke and gas if exposed to an open flame, so it can be used in enclosed areas such as ships and tunnels.
Use this tubing where wire and cable may be exposed to chemicals, oil, and acids.
Resistant to diesel fuel, hydraulic fluid, and lubricating oil, this tubing is often used in vehicles.
Often used to bundle batteries, capacitors, and other electronics, this tubing tightly conforms to objects, similar to shrink wrap. It has excellent resistance to chemicals, oil, and acids.
Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.
A flame-retardant additive makes this polyolefin tubing combustion resistant and minimizes the spread of flames.
A layer of conductive cloth protects wire and cable from signal interference caused by nearby equipment and devices.
Made of woven polyolefin/polyester fabric, this tubing has excellent abrasion resistance so it can be dragged over rough surfaces without damage.
Often used in automated applications such as robotics, this highly flexible silicone rubber tubing withstands continuous motion without cracking and tearing. It resists abrasion and can be dragged over rough surfaces without damage.
With excellent resistance to tears and cuts, this tubing withstands demanding use.
This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.
Made of PVC, this tubing resists chemicals, oil, and solvents. The adhesive lining creates a water-resistant seal when heated.
Create a water-resistant seal—this tubing has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.
Approved for contact with food, this tubing is FDA Compliant 21 CFR 177.1330.
Protect bus bars and other high-voltage devices—this tubing withstands voltages up to 5,000 volts.
After being cleaned with alcohol, this tubing is bagged and sealed in a clean room. It's certified for material quality and purity.
Extra-thick walls provide better protection against abrasion and tears than standard moisture-seal tubing, as well as creating a water-resistant seal.
A different shrink ratio on each end allows this tubing to fit over cable assemblies and wire harnesses with large connections, or around connectors with a 90° elbow.
Use this wrap with heat-shrink tubing to create a moisture-resistant seal. Apply it like tape around wire and cable, then slide the tubing over the wrap. The wrap melts when tubing is heated and bonds to the underlying surface.
Seal the end of crimped connections, such as motor coils, to protect them from moisture.
Organize and route wire and cable in an enclosure—this tubing bundles wires together while allowing them to reach different connection points.
Also known as breakout boots, these splitters insulate and seal the point where wire splits off from cable, or where cables exit from conduit.
Maintain a supply of tubing in a variety of sizes that withstand abrasion, moisture, and chemicals.
Keep general purpose tubing in a variety of sizes on hand.
Protect wire and cable without disconnecting them from an assembly. For a water-resistant seal, this wrap has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.
Create a permanent seal without applying heat. This tubing is also known as cold-shrink tubing.
Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.
Apply heat and these grommets shrink around wire, cable, and cords to keep out dust, debris, and moisture.