We will reply to your message within an hour.
For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.
Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.
For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.
Route pipe, tubing, and conduit across strut channel.
Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.
Hold pipe, tubing, and conduit away from strut channel.
Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.
Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.
Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.
Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.
For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.
Organize multiple lines of pipe, tubing, or hose with a single clamp. They are polyethylene for good chemical and UV resistance.
For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.
Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.
Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.
Slide these clamps into strut channel and snap closed for quick installation with no tools required. They are noncorrosive, nonconductive nylon.
A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.
Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.
Customize these clamps to any object—they have a bend-and-stay design so you can mold them to the size and shape you need. Made of plastic-coated 316 stainless steel, they withstand abrasion, corrosion, and UV rays.
A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.
Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.
A molded cushion reduces vibration and wear from clamp edges, plus it provides a tighter fit around material than standard vibration-damping loop clamps.
These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.
Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.
Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.
A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.
Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.
Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.
These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.
Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.
Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.
For a strong, secure connection, mount these hangers by welding them to a rod.
Use in medium-pressure applications up to 600 psi.
Use in low-pressure applications up to 150 psi.
Use in high-pressure applications up to 1,000 psi.
Snap these clamps around leaking pipe with only your hands. No tools required.
Stop leaks where a fitting and a pipe join without turning off your line.
These clamps are easier to install than worm-drive clamps—crimp the pinch points with pinch-clamp pincers for a secure hold. They are also known as ear clamps.
These pinch clamps come packed in a box with individual compartments for each clamp size. Easier to install than worm-drive clamps, crimp the pinch points with pinch-clamp pincers for a secure hold. They’re commonly known as ear clamps.
Unlike other pinch clamps, these have a unique tongue-and-groove design that creates a gap-free seal to reduce leaks.
Unlike vibration-resistant pinch clamps, these have a torque rating for extra holding power in high-vibration applications. They are also known as high-torque clamps.
Slide these clamps over your hose and heat-shrink them with a heavy duty heat gun. This process lets them conform to any shape hose.
Installing these clamps is a snap—push their interlocking teeth together with your fingers, then squeeze tight with pliers. To remove, use pliers to push sideways and separate the teeth.
Made of our most corrosion resistant stainless steel, these worm-drive clamps stand up to harsh acids and chemicals. Their band is smooth and has rolled edges, so they won’t cut into your hose or tube.
Twist the thumb head with your fingers to tighten these clamps. Once tightened, remove the thumb head to minimize your clamp’s profile and make it harder to tamper with.
Clamps offer extra holding power in high-torque applications.
Not as bulky as our other constant-tension clamps, these round-wire clamps easily fit in cramped spaces. Use in low-pressure applications.
A double ring of thick wire provides a complete seal around large-diameter hose.
Make quick changeovers without sacrificing a tight seal.
These clamps form a 360° seal around your hose or tube to prevent leaks.
Clamps have a slotted hex-head screw that flips up to release the band for quick opening.
These clamps have a wider band than other constant-tension clamps, which provides more coverage and reduces the chance of leaks.
Used to secure Viega PEX fittings to Viega PEX tubing, these clamps meet an ASTM standard to ensure compatibility.
The T-bolt design provides excellent strength and creates a 360° seal. Clamps have a spring that automatically adjusts the clamp diameter when temperatures fluctuate.
To prevent removal, these clamps can only be loosened with a special bit or screwdriver.
One clamp fits a wide range of diameters, so you can always have the right size on hand.
Made of nylon, these clamps have excellent corrosion and chemical resistance, don’t conduct electricity, and weigh less than metal clamps.
These clamps are easier to install than our Extra-Strength Low-Profile Band Clamps. Also known as center-punch clamps, they seal with a quick hammer blow to the buckle.
Designed for both permanent connections and emergency repairs, use these buckles with banding to create your own low-profile hose clamps.
A thumb screw instead of a slotted screw allows you to install these clamps without any tools.
Keep this banding on hand for both permanent connections and emergency repairs. You'll need an installation tool and a buckle (both sold separately) to create a band clamp.
Here's everything you need to make your own 3" diameter and larger custom-length worm-drive clamps.
A raised safety collar around the head of the screw prevents your screwdriver from slipping and damaging the hose or tube.
The end of the band curls back into the buckle—this gives these clamps up to 25% more strength than other low-profile clamps. They are also known as JS-style clamps.
Easy to use, strong, and versatile, these hose clamps are the most common. Tighten their slotted screw with a screwdriver, hex nut driver, or wrench.
Don't worry about your hose and tube expanding and contracting when temperatures fluctuate—these clamps have a Bellville spring that automatically increases and decreases the clamp's diameter.
A dimple in the ear creates spring-like action that allows these clamps to withstand vibration and temperature changes without loosening.
Flip up the slotted hex head screw to quickly release the band. These clamps have rounded edges and a smooth interior, so they won’t cut into hose and tube materials.
An extended tail acts as a liner to protect hose and tube from being cut by the slots in the band.
Remove the bolt and flip open the hinged bridge to install.
The hose clamps in these assortments have a bolt closure that creates a 360° leak-preventing seal. The clamps have rolled edges, so they won’t cut into hose and tube.
The bolt design provides high strength and creates a 360° seal to prevent leaks.
Clamps come packed in a box with individual compartments for each clamp size. To make sure they won’t cut into hose and tube, they have a smooth band with rolled edges.
Clamps have a smooth band with rolled edges to prevent them from cutting into your hose or tube.
Create 4" diameter and larger worm-drive clamps that withstand high-temperature applications.
Create 2" diameter and larger smooth-band worm-drive clamps.
Prevent static charge buildup while securely connecting duct hose with a wire spiral.
Also known as bridge clamps, these worm-drive clamps align with the spiral support on wire duct hose to provide a tight seal.
Unlike other duct hose clamps, these are rated for a maximum work load. Clamps have a quick-release latch that lets you access your line frequently while maintaining your original clamp size.
Flip the toggle latch to install and remove these clamps in seconds.
Color code hose and tube lines in your facility to identify them at a glance.
Use with interlocking-clamp hose fittings to replace a damaged clamp. They consist of two halves held together by nuts and bolts.
Repair pinholes, punctures, and cracks in low-pressure systems with these clamps. Insert tubing into the clamp and tighten the bolts to create a secure seal.
Repair leaks in copper tubing.
These brackets have narrow slots compatible with quick-connect clamps for securing pipe and conduit on the channel side of struts without screws or tools.
For compatibility with quick-connect clamps to secure pipe and conduit without screws and tools, this strut channel has narrow slotted holes.