When installed, these keys fill oval keyways completely, reducing stress on the key and shaft. The rounded ends make it easy to slide gears, hubs, and other components into place. These are also known as feather keys.

Straight keys, with a square or rectangular cross section, are the most common type of key. Install them in keyways to transmit torque from shafts to gears and other components.

Thread a screw through the tapped hole to pop these keys out of a keyway. When installed, they fill oval keyways completely, reducing stress on the key and shaft. The rounded ends make it easy to slide gears, hubs, and other components into place.

Cut this stock to length to create the machine key you need. Straight keys, with a square or rectangular cross section, are the most common type of key. Install in a keyway to transmit torque from shafts to gears and other components.

Slightly larger than the size listed, these oversized keys offer a tight fit in worn keyways.

Make a key that is the exact length you need. Because this key stock is slightly larger than standard key stock, keys will fit tightly in worn keyways.

A rounded bottom allows these keys to rock in their seat to relieve stress on the shaft caused by vibration or misalignment.

Find the key blanks you need to duplicate keys for padlocks, cabinet doors, and locksets.

Padlocks come in a variety of colors for lockout identification compliance. Choose these locks if you need several locks that open with the same key.

Locks have a vertical shackle clearance that's greater than 1" and include a Danger label as well as a write-on label marked Property of. Padlocks come in a variety of colors for lockout identification compliance. Choose these locks if you need several locks that open with the same key.

Choose these locks if you need several locks that open with the same key.

Shackle is concealed to make it difficult to cut. Choose these locks if you need several locks that open with the same key.

Vertical shackle clearance is greater than 1". These corrosion-resistant padlocks are well suited for refineries and marine applications. Choose them if you need several locks that open with the same key.

Shackle is concealed to make it difficult to cut. These corrosion-resistant padlocks are well suited for refineries and marine applications. Choose them if you need several locks that open with the same key.

For added security, locks have specially designed keys that cannot be duplicated and cannot be removed when the lock is open.

Vertical shackle clearance is greater than 1”.

Locks have a vertical shackle clearance that's greater than 1" and include a Danger label as well as a write-on label marked Property of. Padlocks come in a variety of colors for lockout identification compliance. Choose these locks if you want individual locks or groups of locks that open with their own key, but also open with a master key.

Vertical shackle clearance is greater than 1". Padlocks come in a variety of colors for lockout identification compliance. Choose these locks if you want individual locks or groups of locks that open with their own key, but also open with a master key.

Vertical shackle clearance is greater than 1”. Choose these locks if you want individual locks or groups of locks that open with their own key, but also open with a master key.

Vertical shackle clearance is greater than 1". These corrosion-resistant padlocks are well suited for refineries and marine applications. Choose them if you want individual locks or groups of locks that open with their own key, but also open with a master key.

Shackle is concealed to make it difficult to cut.

Choose these locks if you need locks that each open with a different key.

More versatile than other padlocks because the shackles can lock in several vertical positions.

Vertical shackle clearance is greater than 1”.

Locks have a vertical shackle clearance that's greater than 1” and include a Danger label as well as a write-on label marked Property of. Padlocks come in a variety of colors for lockout identification compliance. Choose these locks if you need locks that each open with a different key.

All external parts are plastic, making these locks nonconductive, nonsparking, and nonmagnetic. Locks include a Danger label as well as a write-on label marked Property of. They come in a variety of colors for lockout identification compliance. Choose these locks if you need locks that each open with a different key.

In addition to a vertical shackle clearance that's greater than 1”, these locks have specially designed keys that cannot be duplicated and cannot be removed when the lock is open.

Shackle is concealed to make it difficult to cut.

Vertical shackle clearance is greater than 1". These corrosion-resistant padlocks are well suited for refineries and marine applications. Choose them if you need locks that each open with a different key.

Vertical shackle clearance is greater than 1”.

Open the shackle with a control key as well as the combination.

Compared to other combination padlocks, these have a reinforced body and dial, making the lock more difficult to shim and pull apart. The dial rim is also recessed to prevent tampering. Open the shackle with a control key as well as the combination.

Choose these if you need several locks that open with the same key. Often used on utility meters, vending machines, and for other applications in confined spaces, these locks have a removable post-style shackle.

Choose these locks if you need locks that each open with a different key. Wrap the flexible braided steel shackle around small tools and equipment to prevent theft and unauthorized use.

Choose these locks if you need several locks that open with the same key.

Turn fasteners from either end and reach into tight spots.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. Use to turn screws in hard-to-reach spots.

These keys have an extra-short leg to fit into tight spaces that other tools can’t.

These assorted keys have a ball end that allows angled entry to turn screws in hard-to-reach areas. The bright finish makes them easy to see and less likely to be misplaced.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places. These keys have a bright gold-plated finish that makes them easy to see and less likely to be misplaced.

These assorted keys have a bright finish that's easy to see, so they’re less likely to be misplaced. They turn fasteners from either end and reach into tight spots.

Sets include assorted keys with each size a different color for easy identification. When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

These assorted keys have a retaining ring at the tip that grips inside the recess to ensure screws won’t fall off.

These assorted keys have a detent that grips inside the recess to ensure screws won’t fall off. The ball end allows angled entry to drive fasteners in hard-to-reach areas.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places. These keys have a zinc coating that resists salt-spray exposure.

The assorted tools in these sets have a flexible joint that provides access to fasteners in hard-to-reach areas.

Sets include an assortment of stainless steel keys with a ball end that allows angled entry to turn screws in hard-to-reach areas. Use a stainless steel L-key to protect your stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Protect your stainless steel screws by using a stainless steel L-key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

These assorted keys are made of beryllium copper that is FM approved. They help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Keys turn fasteners from either end and reach into tight spots.

Often used to install carbide inserts in cutting tools, these keys have a small handle that prevents you from generating too much torque when turning a fastener.

These plastic organizers store keys in slots marked with the size.

The T-handle provides a good grip for your whole hand and the long shaft reaches into tight spots.

When working in tight spaces, these short keys fit where others can't.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places. These keys have a textured grip that provides comfort, slip resistance, and maximum torque.

The textured grip provides comfort, slip resistance, and maximum torque. These keys have a long shaft for reaching into tight spots to turn fasteners.

With a simple loop handle, these keys are the economical choice. They have a long shaft for reaching into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.

The long shaft has a ball end for angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

The assorted keys in these sets have a long shaft for more reach and a short shaft for more torque when turning fasteners.

The extra-long shaft lets you access fasteners in deep recesses. To change tips, use a hex key to loosen the set screw.

The ball-end tip has a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

These assorted keys have a retaining ring on the tip that grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

Protect your stainless steel screws by using a stainless steel key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Sets include an assortment of keys with a long shaft for more reach and a short shaft for more torque. Use stainless steel keys to protect your stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

The assorted keys in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 and ASTM F1505-01. They have a long shaft that reaches into tight spots to turn fasteners.

Strong and durable, these multipurpose bits are for use with bit screwdrivers.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

When you don't have exact alignment between the fastener and the bit, the ball end allows angled entry to turn screws in hard-to-reach areas. A retaining ring grips inside the recess to hold screws in place.

Strong and durable, these multipurpose bits are often used with power tools to install sheet metal screws.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

Bits have a different size at each end.

Bits have a different size at each end. An opening at the tips accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

Assortments contain bits with multiple drive styles.

The knurled shank on these bits allows finger tightening. They can also be used with the included screwdriver.

The slightly tapered tip wedges into the screw recess for a secure hold. These are also known as Torx-Align bits.

An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

Sets include an assortment of drivers with soft, contoured handles that provide comfort and the best possible grip for achieving maximum torque.

A scaled-down version of standard screwdrivers, these tools are shorter, slimmer, and easy to take with you.

Sets include an assortment of drivers.

The assorted drivers in these sets have a ball end that allows angled entry to turn screws in hard-to-reach areas.

A holding mechanism at the tip of the tool ensures the screw won’t slip off.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards.

A ratchet mechanism allows you to drive fasteners when there's little space to move the handle.

Insert a bit into the shaft and a magnet holds it in place.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet EN 60900 and IEC 60900.

Press down on the handle’s collar to either adjust the shaft length or remove the shaft and replace it for a different tip. Sets include a handle and multiple reversible shafts.

A scaled-down version of standard changeable-shaft screwdrivers, these tools are shorter, slimmer, and easy to take with you. Remove and replace the shaft to use a different tip size.

The assorted drivers in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet ASTM and IEC standards.