Ladder-Style Steps
Good for use as ladder rungs, cut these steps to size with a metal-cutting saw and weld them in place. For a clean weld, match the step material to the surface you are welding to. These steps must be welded at each end with welds capable of supporting the rated capacity. For those 5 ft. and longer, the maximum cut length is 24". Shorter lengths support higher capacities.
Galvanized steel steps require preparation before welding—grind off the coating from the part of the step you intend to weld. After welding, apply a cold galvanizing spray to the welds to protect against rust.
Serrated steps give you maximum slip resistance and allow liquids and debris to pass through. Perforated steps are less slip-resistant than serrated steps but offer a more comfortable hand grip.
Note: Check local, state, and federal codes, including OSHA, for safe set up and operating practices.
Overall | |||||
|---|---|---|---|---|---|
| Wd. (A) | Dp. (B) | Ht. (C) | Capacity | Each | |
Steel | |||||
With Serrated Tread | |||||
| 17" | 1 1/8" | 1 1/4" | 540 lbs. | 000000 | 000000 |
| 17" | 1 7/8" | 1 1/4" | 540 lbs. | 000000 | 00000 |
| 7 ft. | 1 1/8" | 1 1/4" | 250 lbs. for 18"-24" Cut Lengths, 540 lbs. Up to 18" Cut Lengths | 0000000 | 000000 |
| 7 ft. | 1 7/8" | 1 1/4" | 250 lbs. for 18"-24" Cut Lengths, 540 lbs. Up to 18" Cut Lengths | 000000 | 000000 |
| 20 ft. | 1 1/8" | 1 1/4" | 250 lbs. for 18"-24" Cut Lengths, 540 lbs. Up to 18" Cut Lengths | 000000 | 000000 |
| 20 ft. | 1 7/8" | 1 1/4" | 250 lbs. for 18"-24" Cut Lengths, 540 lbs. Up to 18" Cut Lengths | 000000 | 000000 |
With Perforated Tread | |||||
| 5 ft. | 1 1/4" | 1 1/2" | 330 lbs. for 18"-24" Cut Lengths, 450 lbs. Up to 18" Cut Lengths | 00000000 | 00000 |
| 5 ft. | 1 5/8" | 1 1/8" | 250 lbs. for 18"-24" Cut Lengths, 330 lbs. Up to 18" Cut Lengths | 00000000 | 00000 |
| 5 ft. | 2 1/4" | 1 1/2" | 570 lbs. for 18"-24" Cut Lengths, 760 lbs. Up to 18" Cut Lengths | 00000000 | 00000 |
Galvanized Steel | |||||
With Perforated Tread | |||||
| 5 ft. | 1 1/4" | 1 1/2" | 330 lbs. for 18"-24" Cut Lengths, 450 lbs. Up to 18" Cut Lengths | 00000000 | 00000 |
| 5 ft. | 1 5/8" | 1 1/8" | 250 lbs. for 18"-24" Cut Lengths, 330 lbs. Up to 18" Cut Lengths | 00000000 | 00000 |
| 5 ft. | 2 1/4" | 1 1/2" | 570 lbs. for 18"-24" Cut Lengths, 760 lbs. Up to 18" Cut Lengths | 00000000 | 00000 |
Aluminum  | |||||
With Serrated Tread | |||||
| 17" | 2" | 1 1/2" | 540 lbs. | 0000000 | 00000 |
| 7 ft. | 2" | 1 1/2" | 250 lbs. for 18"-24" Cut Lengths, 540 lbs. Up to 18" Cut Lengths | 0000000 | 000000 |
With Perforated Tread | |||||
| 5 ft. | 1 1/4" | 1 1/2" | 310 lbs. for 18"-24" Cut Lengths, 410 lbs. Up to 18" Cut Lengths | 00000000 | 00000 |
| 5 ft. | 1 5/8" | 1 1/8" | 220 lbs. for 18"-24" Cut Lengths, 290 lbs. Up to 18" Cut Lengths | 00000000 | 00000 |
| 5 ft. | 2 1/4" | 1 1/2" | 540 lbs. for 18"-24" Cut Lengths, 720 lbs. Up to 18" Cut Lengths | 00000000 | 00000 |
304 Stainless Steel | |||||
With Serrated Tread | |||||
| 17" | 1 1/8" | 1 1/4" | 540 lbs. | 0000000 | 00000 |
| 7 ft. | 1 1/8" | 1 1/4" | 250 lbs. for 18"-24" Cut Lengths, 540 lbs. Up to 18" Cut Lengths | 000000 | 000000 |
With Perforated Tread | |||||
| 5 ft. | 1 1/4" | 1 1/2" | 230 lbs. for 18"-24" Cut Lengths, 300 lbs. Up to 18" Cut Lengths | 00000000 | 00000 |
| 5 ft. | 2 1/4" | 1 1/2" | 380 lbs. for 18"-24" Cut Lengths, 510 lbs. Up to 18" Cut Lengths | 00000000 | 000000 |
Fold-Up Steps
Flip these steps down when you need them and fold them up when you don’t. They can be bolted onto a stable surface, such as a wall. All steps have a diamond-plate or serrated tread for maximum slip resistance.
Style 1 have a cutout and rounded edges that you can grab with your hand if needed.
Style 2 are large enough to support your whole foot.
Style 4 are large enough to hold both of your feet. Yellow steps are highly visible and reduce tripping and safety hazards when left unfolded. Steps with a spring-loaded hinge automatically fold up when you step off.
Zinc-plated, chrome-plated, and powder-coated steel steps have a protective layer that prevents rust.
Stainless steel steps are corrosion resistant. 304 stainless steel steps have good chemical resistance. 316 stainless steel steps offer the highest corrosion resistance and the best protection against chemicals and salt water.
Note: Check local, state, and federal codes, including OSHA, for safe operating practices.
Overall | Step | Mounting Holes | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ht. (A) | Wd. (B) | Dp. (C) | Wd. | Dp. | Tread | Projection | Wt., lbs. | Cap. | Mounting Hardware Included | No. of | Dia. | Ctr.-to-Ctr. Ht. | Each | |
Zinc-Plated Steel | ||||||||||||||
| 4 3/4" | 1 3/4" | 3 3/4" | 4 3/8" | 2 1/8" | Diamond Plate | 3 3/4" | 2 | Not Rated | No | 2 | 5/16" | 3 7/8" | 0000000 | 000000 |
| 5" | 3 1/2" | 6 5/8" | 6 1/2" | 5 1/4" | Diamond Plate | 6 5/8" | 4 | Not Rated | No | 2 | 5/16" | 3 7/8" | 0000000 | 00000 |
304 Stainless Steel | ||||||||||||||
| 4 3/4" | 1 3/4" | 3 3/4" | 4 3/8" | 2 1/8" | Diamond Plate | 3 3/4" | 2 | Not Rated | No | 2 | 5/16" | 3 7/8" | 0000000 | 00000 |
316 Stainless Steel | ||||||||||||||
| 4 3/8" | 1 7/8" | 3 1/2" | 3 3/8" | 2" | Diamond Plate | 3 1/2" | 1 | Not Rated | No | 2 | 5/16" | 3 5/8" | 0000000 | 00000 |
Overall | Step | Mounting Holes | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ht. (A) | Wd. (B) | Dp. (C) | Wd. | Dp. | Tread | Projection | Wt., lbs. | Cap. | Mounting Hardware Included | No. of | Dia. | Ctr.-to-Ctr. Ht. | Ctr.-to-Ctr. Wd. | Each | |
Chrome-Plated Steel | |||||||||||||||
| 4 7/8" | 4" | 8 1/2" | 6 3/4" | 6 3/8" | Diamond Plate | 8 1/2" | 5 | Not Rated | No | 4 | 5/16" | 4" | 2 1/4" | 0000000 | 000000 |
Overall | Step | Mounting Holes | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ht. (A) | Wd. (B) | Dp. (C) | Wd. | Dp. | Tread | Projection | Wt., lbs. | Cap. | Mounting Hardware Included | No. of | Dia. | Ctr.-to-Ctr. Ht. | Ctr.-to-Ctr. Wd. | Each | |
304 Stainless Steel | |||||||||||||||
| 3 3/8" | 2 3/8" | 5 5/8" | 1" | 4 1/4" | Serrated | 5 5/8" | 1 | Not Rated | No | 4 | 3/16" | 2 5/8" | 1 3/4" | 0000000 | 000000 |
Overall | Step | Mounting Holes | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ht. (A) | Wd. (B) | Dp. (C) | Wd. | Dp. | Tread | Projection | Wt., lbs. | Cap., lbs. | Mounting Hardware Included | No. of | Dia. | Ctr.-to-Ctr. Wd. | Each | |
Gray Powder-Coated Steel | ||||||||||||||
| 4" | 15" | 10 3/4" | 14 1/4" | 9 1/2" | Serrated | 10 3/4" | 11 | 350 | No | 2 | 9/16" | 13" | 0000000 | 000000 |
Gray Powder-Coated Steel—With Spring-Loaded Hinge | ||||||||||||||
| 4" | 15" | 10 3/4" | 14 1/4" | 9 1/2" | Serrated | 10 3/4" | 11 | 350 | No | 2 | 9/16" | 13" | 0000000 | 000000 |
Yellow Powder-Coated Steel | ||||||||||||||
| 4" | 15" | 10 3/4" | 14 1/4" | 9 1/2" | Serrated | 10 3/4" | 11 | 350 | No | 2 | 9/16" | 13" | 0000000 | 00000 |
Antislip Step Covers
Weld these covers to the rungs of your wall and tank ladders for excellent slip resistance. Covers fit square and round rungs. Can be cut with a hand grinder or miter saw using a masonry blade.
Strut Channel Handles
Mount between two strut channels to create a handhold. Made of zinc-plated steel, these handles resist corrosion in wet environments.
Mounting Holes | ||||||
|---|---|---|---|---|---|---|
| Lg. | Ht. | No. of | Dia. | Mounting Fasteners Included | Each | |
For 1 5/8" Channel Wd. | ||||||
Zinc-Plated Steel | ||||||
| 13 5/8" | 1 5/8" | 2 | 9/16" | No | 0000000 | 000000 |