Rated for use in damp locations, these lights withstand humidity and moisture.

These lights are sealed to protect against humidity, moisture, and dripping and splashing liquids.

These lights are UL rated for use in hazardous locations where flammable/combustible gases, vapors, and liquids may be present.

Plug in these flashlights and they’ll automatically light up when the power goes out. There’s no need to regularly replace the batteries—they recharge on the base when it’s plugged into an outlet.

Small enough to fit in your pocket.

Tilt the head on these flashlights to aim light exactly where it's needed. They have a flat bottom, so you can work hands-free without them rolling away.

If the power goes out, you’ll find these flashlights right away.

Shine light into hard-to-reach spaces with these flexible-arm flashlights.

Clip these little flashlights to a baseball cap or a surface to light up your work.

Rated for use in environments where hazardous material is present.

Small enough to fit in your shirt pocket, these penlights safely light up work in explosion-prone areas. They’re rated for areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

All of these flashlights stand up to wet environments.

Keep your hands free by wearing a flashlight on your head.

Clip these headlamps right into a mount on your tactical or rescue helmet.

Light up work while staying visible in high-risk areas. These headlamps have LEDs on the head band so forklift and truck drivers can see you.

Hang a string of lights overhead to brighten wet jobsites. IP rated, these lights are sealed to keep out dust and moisture from washdowns, splashes, and sprays, even outdoors.

A series of bulb heads are attached to a power cord to provide overhead lighting for job sites.

A flexible design allows these lights to be suspended above, wrapped around, or routed through areas on the job site.

Keep excess cords out of your way—the reel locks the cord at any length and retracts it when not in use.

Pop these lights on magnetic surfaces to brighten wet spaces. Rated NEMA 6 and ETL listed, you can splash, spray, or dunk them in water, and they’ll keep working.

Because these lights are compatible with DeWalt rechargeable batteries, you can keep one type of cordless tool battery on hand. Their head pivots to aim light where it's needed in areas that don't have electrical power service.

Bring light to areas that don't have electrical power service.

From pipes to pallet racks to control panels—these lights clamp onto almost anything and swivel to direct light just where you need it.

Aim light where you need it—even in explosion-prone spaces—by raising, lowering, and tilting these lights on their tripod. Rated NEC Classes I, II, III, and Zone 0, they’re safe to use near ignitable concentrations of flammable or combustible gas, dust, or fibers.

Bring light to explosion-prone work areas. Rated NEC Class I, these lights are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Brighten remote areas, even if they’re damp or rainy. These floodlights are IP rated to keep out humidity and dripping, splashing, and falling liquids.

Flood dark, remote jobsites with multiple tiers of light. These cordless lights stack on top of each other to focus a strong beam of light in one direction.

Compact and easy to carry, these ETL listed lights stand up to dripping, splashing, and falling liquids. The head adjusts up and down to direct light where it's needed.

Raise, lower, and tilt these lights to brighten your work in wet spaces.

Light up remote spaces without having to keep track of a new cordless tool battery. These floodlights run on a Milwaukee M18 battery (sold separately). These lights extend up to 7 ft. tall and have a pivoting head to direct light where you need it.

Brighten remote spaces with the DeWalt rechargeable battery that’s already in your toolkit. These floodlights extend up to 7 ft., and the light head turns at any angle to aim light where it’s needed.

Powered by the sun, these security lights function in areas that don’t have access to electricity. They’re often used to shine light on parking lots, landscaping, signs, entryways, and other outdoor spaces.

Mount this light on a pole to illuminate pedestrian areas such as streets and walkways.

Also known as pigtail holders. Temporarily wire these sockets to provide light during construction.

Illuminate exits during power failures and other emergencies—these signs have battery-powered emergency lights. The backlit message meets UL 924 regulations for visibility.

These signs are rated NEMA 4X for corrosion resistance and washdown environments.

Direct your signal with these lights; they flash in one direction.

These lights cycle through three different flashing patterns.

These lights cycle through three different flashing patterns.

These lights can switch between being continuous or flashing.

These lights can switch between continuous, flashing, or revolving.

Small as hockey pucks, these lightweight strobe lights mount to surfaces and are unobtrusive when they’re turned off.

As small as a hockey puck and compatible with standard 12-volt vehicle plugs, these strobe lights are inconspicuous when not in use and quick to connect.

These strobe lights flash multiple times per cycle, making them easier to spot than standard strobe lights.

Rated NEMA 4X and 13 for protection from dirt, washdowns, corrosion, and oil/coolant spraying.

You can use these lights outdoors and they will still be visible. Rated IP67 for harsh environments.

Mount the M22 male thread on the bottom of the light through a hole and then secure using the included nut.

Choose from seven colors, including nontraditional colors such as magenta and turquoise, for a custom four-light stack light.

Design a stack light with your choice of light pattern and color. Start with a base, then add up to five modules total—twist and lock them together.

The quick-connect four-pole M12 plug on these lights makes them easy to hook up and configure.

Get notified about equipment issues even when you aren't around your machines. These lights connect to your computer via Ethernet, allowing you to set up email alerts when there is a problem with a machine, server, or conveyor.

Use a computer to program colors, lighting patterns, and sounds to communicate a variety of status conditions, material levels, and cycle times—these stack lights have 21 colors and 11 sounds.