Similar in function to tubular machine lights, except strip machine lights have a flat lens that directs light downward.

With a slimmer profile than other strip machine lights, these lights fit in tight spots on workspaces and inside machinery because they don’t have a circuit board.

Just like traditional tubular lights that illuminate your machine with a bright white light, these lights can also be programmed to switch over to a red or green light for communicating machine status.

Suspend these lights overhead or mount them above your workspace.

The articulating arm on these lights holds its position better than gooseneck-arm lights, especially around vibration.

Pivot the head to cast a narrow beam of light to exactly where it's needed.

Shine light on machinery and through the sight glass on tanks to inspect food, brewery, chemical, pharmaceutical, and bio-tech processing lines.

Faster and easier to reposition than articulating-arm lights, these gooseneck-arm lights attach to your workspace for additional lighting.

A flexible design allows these lights to be suspended above, wrapped around, or routed through areas on the job site.

A mounting clip at the base lets you attach these lights to nearby surfaces.

Keep excess cords out of your way—the reel locks the cord at any length and retracts it when not in use.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

Light up damp areas—these lights seal out moisture and humidity. They’ll even work in areas with frequent washdowns. Rated NEMA 4X, they withstand spraying liquid, resist corrosion, and keep out dust.

Because these lights are compatible with DeWalt rechargeable batteries, you can keep one type of cordless tool battery on hand. Their head pivots to aim light where it's needed in areas that don't have electrical power service.

Point light where it’s needed—even in wet areas. These lights are sealed against splashing and dripping water.

Splashes and drips are no problem for these lights. They don’t need an outlet, so you can bring them wherever you need them.

Aim light where you need it—even in explosion-prone spaces—by raising, lowering, and tilting these lights on their tripod. Rated NEC Classes I, II, III, and Zone 0, they’re safe to use near ignitable concentrations of flammable or combustible gas, dust, or fibers.

Bring light to explosion-prone work areas. Rated NEC Class I, these lights are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Compact and easy to carry, these ETL listed lights stand up to dripping, splashing, and falling liquids. The head adjusts up and down to direct light where it's needed.

Brighten remote areas, even if they’re damp or rainy. These floodlights are IP rated to keep out humidity and dripping, splashing, and falling liquids.

Flood dark, remote jobsites with multiple tiers of light. These cordless lights stack on top of each other to focus a strong beam of light in one direction.

Brighten areas of a jobsite with these floodlights, and move them at a moment’s notice.

Light up remote spaces without having to keep track of a new cordless tool battery. These floodlights run on a Milwaukee M18 battery (sold separately). These lights extend up to 7 ft. tall and have a pivoting head to direct light where you need it.

Raise, lower, and tilt these lights to brighten your work in wet spaces.

A motion sensor turns on these lights when an enclosure door is opened. Mount them inside cabinets, closets, and other enclosed spaces.

Clip these headlamps right into a mount on your tactical or rescue helmet.

Light up work while staying visible in high-risk areas. These headlamps have LEDs on the head band so forklift and truck drivers can see you.

Light up work even when your visor is up. These headlamps come with three attachments that fit with anything from your hard hat to your baseball cap.

Light up your work from under your brim.

Mount the M22 male thread on the bottom of the light through a hole and then secure using the included nut.

Mount these lights horizontally or vertically in places where a tower will not fit.

Use these lights in tight spaces in place of a tower. They emit three colors from a single lens.

These lights emit three colors from a single lens and can be mounted in tight spaces where a tower will not fit.

Get notified about equipment issues even when you aren't around your machines. These lights connect to your computer via Ethernet, allowing you to set up email alerts when there is a problem with a machine, server, or conveyor.

Good for tight spaces where a tower of lights won't fit, these emit three colors from a single lens.

Rated NEMA 4X and 13 for protection from dirt, washdowns, corrosion, and oil/coolant spraying.

Make a custom panel light with your choice of light and lens cap color.

You can use these lights outdoors and they will still be visible. Rated IP67 for harsh environments.

Highlight small, specific areas with intensely bright light to help your machine vision camera home in on the details of your product.

Detect edges, take measurements, and spot holes with your machine vision camera by passing objects over these backlights.

The most versatile of our machine vision lights, these bar lights can be used alone, installed side-by-side, or assembled into a ring light.

Also known as beacon lights and signal lamps, these bulbs provide high-intensity light so they're often used in security warning devices and machinery.