These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.

At approximately one-third the height of standard versions, these rails provide linear shaft support in applications with low vertical clearance. They provide stability over the entire length of shaft, allow virtually unlimited travel lengths, and eliminate bending under moderate to heavy loads.

Combine these general purpose shafts with a linear bearing and shaft support to create a basic linear motion system.

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Clip retaining rings into the grooves to separate and position collars, supports, and housings.

These two-piece supports allow access to the shaft without needing to slide out the shaft or uninstall the support. Use them to brace the end of a linear shaft when working with light to medium loads where shaft alignment is not critical. Tighten the included clamping screws to secure.

Create a support that fits the exact dimensions of your shaft. Good for use with square- and hex-profile shafts, these aluminum supports also work with round shafts of any diameter up to 1". Use them for light-to-medium-load linear motion applications where shaft alignment is not critical.

These carriages and guide rails are steel.

Designed specifically for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

Adapt most 15 mm guide rails to fit on T-slotted assemblies.

With a plastic cage that surrounds the ball bearings to prevent them from colliding, these extra-wide carriages run quietly for many cycles without needing maintenance. All of these carriages have a wide base and low-profile design to stabilize moment (twisting) and off-center loads better than other carriages.

These tiny carriages and guide rails are sized for electronic and other precision applications.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

Use these carriages and guide rails in temperatures up to 300° F.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

Fasten loads on the side of these carriages and add linear motion to a T-slot assembly.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

C-shaped guide rails grip the carriage around the outside to support linear motion along walls and other vertical surfaces.

A handle locks these carriages in place on curved paths, loops, and circuits in assembly stations and other repetitive processes.

A handle on the side of the carriage locks the carriage in place.

Mount along a wall or other vertical surface.

Create a self-aligning carriage and guide rail system to compensate for mounting surfaces that aren't parallel.

V-shaped rollers and rails allow these carriages to operate well in dirty environments because the debris won't get trapped on the rail.

Nylon rollers provide low-friction movement for light loads and corrosive environments.

These steel track rollers and guide rails support loads up to 300 lbs.

With a row of crossed-roller bearings on each side of the rail, these slides have over twice the load capacity of standard low-friction slides and are better for handling shock loads.

Good for use in pick-and-place applications, machine tool doors, and telescopic press arms, these rugged slides are designed to carry heavy loads.

Use these slides in a variety of manual-positioning applications for laboratory and production equipment as well as for positioning parts for drilling, fastening, assembly, and measuring.

Made with Frelon bearings, these slides have over four times the load capacity of standard positioning slides.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

These slides fully extend for convenient access to the back of drawers.

Half the length of other drawer slides we sell, these slides install in small-parts cabinets.

Open drawers from either side of a cart or cabinet—these slides let drawers pass through for two-way access to contents.

A lever locks the drawer in the open as well as closed position; push the lever to release the lock.

These slides provide full extension for convenient access to the back of your drawers.

A stop holds the drawer open; push firmly on the drawer to close.

When you don't have enough clearance for side-mount or under-the-counter slides, mount these to the base of your drawer.

Mounting to the tops and bottoms of drawers, these steel slides support drawers even if they’re tall and hold heavy equipment.

Add your own stepper motor and controller to precisely move the ball screw and carriage smoothly at high speeds, like a head on an inkjet printer.