Similar in function to tubular machine lights, except strip machine lights have a flat lens that directs light downward.

With a slimmer profile than other strip machine lights, these lights fit in tight spots inside machinery because they don’t have a circuit board.

With a smooth, shatterproof lens, these lights have no crevices where debris can accumulate. Their stainless steel connectors, plastic lens, and mounts resist acids, alkalis, and other chemicals commonly used in food environment washdowns.

Suspend these lights overhead or mount them above your workspace.

These thin, flexible lights wrap around equipment, hide under cabinets, and squeeze into tight spaces—all you need is an outlet. Just peel and stick to attach them to any smooth surface.

These lights cast a narrow beam of light. With a gooseneck arm, they are faster and easier to reposition than articulating-arm lights.

Faster and easier to reposition than articulating-arm lights, these gooseneck-arm lights attach to your workspace for additional lighting.

Stretch the arm to bring light directly over your work—even across a large surface. Also known as articulating arm lights, these lights have rigid sections that hold their position steady, including when fully extended.

A flexible design allows these lights to be suspended above, wrapped around, or routed through areas on the job site.

Hang these lights above your workspace—they shine through long tubes to distribute even light with minimal glare and shadows. Carry them where you need them and suspend them from pipes, beams, and other overhead surfaces.

Light up damp areas—these lights seal out moisture and humidity. They’ll even work in areas with frequent washdowns. Rated NEMA 4X, they withstand spraying liquid, resist corrosion, and keep out dust.

A mounting clip at the base lets you attach these lights to nearby surfaces.

Point light where it’s needed—even in wet areas. These lights are sealed against splashing and dripping water.

Bring light to areas that don't have electrical power service.

Because these lights are compatible with DeWalt rechargeable batteries, you can keep one type of cordless tool battery on hand. Their head pivots to aim light where it's needed in areas that don't have electrical power service.

Aim light where you need it—even in explosion-prone spaces—by raising, lowering, and tilting these lights on their tripod. Rated NEC Classes I, II, III, and Zone 0, they’re safe to use near ignitable concentrations of flammable or combustible gas, dust, or fibers.

Bring light to explosion-prone work areas. Rated NEC Class I, these lights are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Compact and easy to carry, these ETL listed lights stand up to dripping, splashing, and falling liquids. The head adjusts up and down to direct light where it's needed.

Brighten remote areas, even if they’re damp or rainy. These floodlights are IP rated to keep out humidity and dripping, splashing, and falling liquids.

Brighten remote areas using the same battery as your other cordless Milwaukee tools.

Bring light to remote, wet areas. These floodlights are IP rated to handle humidity and dripping, splashing, and falling liquids. Adjust their tripod up and down to direct light as far as you need.

Brighten areas of a jobsite with these floodlights, and move them at a moment’s notice.

Brighten remote spaces with the DeWalt rechargeable battery that’s already in your toolkit. These floodlights extend up to 7 ft., and the light head turns at any angle to aim light where it’s needed.

A motion sensor turns on these lights when an enclosure door is opened. Mount them inside cabinets, closets, and other enclosed spaces.

Illuminate your electronics cabinets and racks with long-lasting LED lights.

Clip these headlamps right into a mount on your tactical or rescue helmet.

Light up work while staying visible in high-risk areas. These headlamps have LEDs on the head band so forklift and truck drivers can see you.

Light up work without risking an explosion. NEC rated, these headlamps are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Drop these headlamps in water and they’ll still work—they’re IP rated to withstand submersion for at least 30 minutes.