Simple to use, these switches actuate with a quick push.

The built-in contact block in these switches extends behind the panel half the depth of most other 22 mm switches, saving valuable space.

A base that lights up draws attention to emergency stops. When pushed, these switches immediately cut power.

Save space on your panel by using one switch for several tasks. These switches actuate with the push of a button.

Immediately cut power with a single push.

More durable than standard metal switches, these can handle tough, repetitive use.

Actuate these switches with a quick push. A housing seals in anything that could ignite flammable material, so you can use them where ignitable gas and dust may be present.

Immediately cut power with a single push.

Save space on a panel by using one switch to perform multiple switching functions.

A protective plastic enclosure resists dents, chips, and cracks, so you can install these switches outside of panels.

Use these switches where ignitable gas and dust may be present. They're rated for use in hazardous locations.

Made of yellow polycarbonate plastic, these enclosed switches are easy to see and resist dents, chips, and cracks. They are more corrosion resistant than aluminum enclosed switches and withstand washdowns and oil/coolant spraying.

Mount these switches in an outlet box. Also known as palm-button switches, they have a large button that makes them easy to use even while wearing gloves.

These switches meet MIL-S-3950.

Prevent accidental actuation—these toggle switches must be pulled up before they can switch a circuit.

Able to withstand high currents, these switches are often used with motors and pumps.

Rated IP67 for protection from dust and temporary submersion.

The wide surface of these switches makes them easy to press on and off, even if your hands are full and you need to use an elbow.

Prevent accidental actuation from bumps or vibration—these switches require you to grip and twist the lever to turn the switch. The contact block and actuator are all one piece, so they won’t separate in high-vibration applications.

Rated NEMA 4, 13, and IP66, these metal switches are protected from washdowns and oil/coolant spraying. Install them in 30 mm dia. cutouts.

Avoid accidental actuation—these switches won’t turn on or off until you grip and twist the lever. Install in a 16 mm dia. cutout.

Operate these switches hands-free when working in damp or humid environments.

Use this switch for intermittent, light-duty applications.

Choose an actuator and contact block to make your own 16 mm switch.

Choose an actuator and contact block to make your own 30 mm switch.

Sized for 22 mm dia. panel cutouts, these switches require a key to turn circuits on or off, limiting access to sensitive equipment.

Install these key switches in 3/4" dia. panel cutouts. They require a key to turn circuits on or off, limiting access to sensitive equipment.

These 16 mm switches require a key to turn circuits on or off, limiting access to sensitive equipment.

Reset fire panels, or open electromagnetic locks, electric strikes, and automatic door openers. These switches require a key to turn circuits on or off, limiting access and preventing accidental activation.

Safe to use near ignitable gases and dust, the housing on these switches seals in anything that could ignite flammable material. Yank the cable anywhere along your line to quickly cut power in emergencies.

Turn these switches by hand.

A durable rubber housing covers the buttons and protects these switches from impact.

Use fingerprints to confirm the identity of personnel before granting access to secure areas or equipment.

Flip a switch from here, there, or anywhere—these switches connect wirelessly to your phone or smart device.

Also known as three-way switches, these are often used in large, open workspaces and can be wired on opposite ends of the room to control lights on the same circuit.

Similar to a seesaw, these switches have an actuator that pivots when pressed to turn them on or off.

Secure sensitive lighting equipment; these switches have a round key that is difficult to duplicate.

Designed to mount on an electrical enclosure, these switches control motors, lighting, and electric heat circuits.

Safely turn motors on and off near ignitable gases and dust—the housing on these switches seals in anything that could ignite flammable material.

Use these switches with motors that run forward and backward, such as motors for conveyor belts.

Rated NEMA 4X, these enclosed starters are protected from corrosion and washdowns.

Sealed coils protect these switches against moisture, heat, dirt, and mechanical and thermal stress.

Protect electrical equipment from overcurrent and undercurrent damage—these relays continuously monitor current flow.

Small enough to fit in tight spaces, these circuit breakers mount through panels and are UL 489-rated for branch circuit protection.

Mount these circuit breakers directly to DIN rail to protect equipment and wiring in an area of your facility from overloads and short circuits.