McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    10 Products

    Switch Contact Blocks

    Image of Product. Front orientation. Switch Contact Blocks.
    Make or break an electrical circuit. These contact blocks mount to manual switches and transmit an electrical signal when the switch actuator is engaged. You can stack multiple blocks, so a single switch can control several circuits. This is helpful in setups that require multiple systems to turn on or off at the same time. For example, the switch on a conveyor line could turn off the conveyor and turn on a diverter and alarm.
    No. of Circuits
    Controlled
    Switch Starting
    Position
    No. of
    Terminals
    Switch
    Designation
    Wire
    Connection
    Enclosure
    Rating
    For Switch Manufacturer
    Series
    Each
    Schneider Electric
    11 Off
    		2SPST-NO
    		Screw TerminalIP20
    		XB58008N11000000
    11 Off
    		2SPST-NO
    		Screw TerminalIP20
    		9001K, 9001SK9235K9700000
    11 On
    		2SPST-NC
    		Screw TerminalIP20
    		XB58008N1200000
    11 On
    		2SPST-NC
    		Screw TerminalIP20
    		9001K, 9001SK9235K9800000
    21 Off and 1 On
    		4DPST-1NO/1NC
    		Screw TerminalIP20
    		9001K, 9001SK9235K9900000
     
    Schneider Electric—Hermetically Sealed
    11 Off
    		2SPST-NO
    		Screw Terminal—9001K71025K115000000
    11 On
    		2SPST-NC
    		Screw Terminal—9001K71025K116000000
     

    Joystick Switches

    Intuitively steer and position cranes, robot arms, and other machinery that moves in multiple directions—your equipment will follow the movements you make with these joysticks. They control multiple circuits as you move them in different directions and patterns. Assemble a complete switch with an actuator and at least one contact block (sold separately).
    Actuators
    Image of Product. Front orientation. Joystick Switches.
    All actuators include a mounting clip that can fit up to two contact blocks. They’re NEMA and IP rated for protection from dust, washdowns, and oil/coolant spraying.
    2 Positions—Two-position actuators require one to four contact blocks.
    4 Positions—Four-position actuators require two to four contact blocks. They are off in the center position.
    Momentary Switch—Momentary actuators can only be locked in the off position.
    Maintained Switch—Maintained actuators can be locked in any position.
    Chrome-Plated Steel—Chrome-plated steel actuators resist wear better than rubber actuators.
    Direction of
    Operation
    Switch
    Action
    Actuator Material
    Dp. Behind
    Panel
    Enclosure Rating
    Mfr.
    Each
    2 Positions for 30 mm (1 3/16") Diameter Panel Cutouts
    Down, UpMomentary
    		Chrome-Plated Steel1 7/16"IP66, NEMA 6, NEMA 13
    		Schneider Electric71025K1120000000
    Down, UpMaintained
    		Chrome-Plated Steel1 7/16"IP66, NEMA 6, NEMA 13
    		Schneider Electric71025K113000000
     
    4 Positions for 30 mm (1 3/16") Diameter Panel Cutouts
    Down, Left, Right, UpMomentary
    		Chrome-Plated Steel1 7/16"IP66, NEMA 6, NEMA 13
    		Schneider Electric71025K114000000
     
    Blocks
    Image of Product. Front orientation. Switch Contact Blocks.
    No. of Circuits
    Controlled
    Switch Starting
    Position
    No. of
    Terminals
    Switch
    Designation
    Wire
    Connection
    Each
    For Schneider Electric Switches
    11 Off
    		2SPST-NO
    		Screw Terminal71025K1150000000
    11 On
    		2SPST-NC
    		Screw Terminal71025K116000000
     
    back to top