Simple to use, these switches actuate with a quick push.

A housing seals in anything that could ignite flammable material, so you can use these switches where explosive gas, dust, and fibers may be. They actuate with a quick push.

The built-in contact block in these switches extends behind the panel half the depth of most other 22 mm switches, saving valuable space.

Install in 10 mm dia. cutouts.

Operate low-voltage devices that require less than 48 volts, such as doorbells and buzzers.

Operate low-voltage devices that require less than 48 volts, such as doorbells and buzzers.

Sized for 4 mm or 6 mm panel cutouts, these switches are often used with circuit boards to control electronics.

More durable than standard metal switches, these can handle tough, repetitive use.

Actuate these switches with a quick push. A housing seals in anything that could ignite flammable material, so you can use them where ignitable gas and dust may be present.

Send a signal from your circuit board with the push of a button.

Install in 14 mm dia. cutouts.

Actuate these switches with a quick push.

With a stainless steel enclosure, these switches are more durable than aluminum and plastic. They're rated NEMA 4X for protection from corrosion and washdowns.

A lightweight yet durable alternative to stainless steel enclosed switches, these aluminum enclosed switches withstand corrosion, oil, and washdowns.

Often used to trigger alarms, these switches have a recessed button to prevent accidental activation. Mount under desks or in other discrete locations to avoid drawing attention.

These familiar push-button switches mount to flat surfaces.

Snap these switches onto your T-slotted framing rails—no need to drill or disassemble your existing structure.

These switches meet MIL-S-3950.

Prevent accidental actuation—these toggle switches must be pulled up before they can switch a circuit.

Built into a terminal block, these switches mount to DIN rail.

The wide surface of these switches makes them easy to press on and off, even if your hands are full and you need to use an elbow.

Grip and twist a lever to turn these switches on or off—they’re designed to prevent accidental actuation. Install them into standard-sized panel cutouts.

Made for areas where ignitable gas and vapor may be present, these switches have a housing that seals in anything that could spark flammable material.

The enclosure not only protects these switches, but also adds options for how you install them.

These switches are rated for environments where hazardous material is present.

Rated NEMA 6P and IP68, these switches are protected against washdowns, corrosion, and temporary submersion.

Control equipment from up to 40 feet away—these switches include a transmitter and a receiver that connects to equipment.

When the pedal is pressed, the built-in potentiometer adjusts the resistance to vary the speed for motor drives.

Send signals to equipment up to 130 feet away. Because these foot switches are self-powered, they eliminate the clutter of wires and the fuss of batteries.

Choose an actuator and contact block to make your own 16 mm switch.

Choose an actuator and contact block to make your own 30 mm switch.

Designed for use near ignitable gases, fibers, and dust, these switches have a housing that seals in anything that could ignite flammable material. They require a key to turn circuits on or off, preventing accidental activation and limiting access.

Reset fire panels, or open electromagnetic locks, electric strikes, and automatic door openers. These switches require a key to turn circuits on or off, limiting access and preventing accidental activation.

Control machinery from a safe distance, or use these switches as call buttons.

These switches withstand temporary submersion.

Never worry about your pendant switch losing power. These pendant switches generate enough power from pushing the button to send a signal to a receiver up to 330 feet away.

Step on these mats to control doors, lights, or alarms.

Prevent personnel from getting too close to dangerous equipment while it’s running. Step anywhere on these mats and they can turn on warning lights and alarms or shut down equipment.

Customize the length of these switches by cutting them from a 50-foot roll.

These mats fit under carpeting or anywhere else you want to hide them.

Rated IP67 and NEMA 6, these switch mats withstand washdowns.

Use fingerprints to confirm the identity of personnel before granting access to secure areas or equipment.

Rated NEMA 4, these switches are protected from washdowns.

Prevent changes in frequency from damaging sensitive equipment.