We will reply to your message within an hour.
These steel anchors are available with corrosion-resistant finishes.
These 18-8 stainless steel anchors have good chemical resistance.
More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.
Keep fixtures solidly in place—these anchors have two locking wedges that won't shake loose.
A zinc plating provides corrosion resistance in wet environments.
The removable flat head provides a flush finish in countersunk holes.
An open-end cap nut provides a finished appearance.
Also known as mungo anchors, these have large fins that prevent rotation.
Use with any type of sheet metal or wood screw.
Also known as lag shields, these anchors are designed for use with large-diameter wood screws.
Often referred to as four-way expansion anchors, these expand in four directions to resist loosening from vibration.
Also known as caulk-in anchors, these stay secure when there's not much material to hold.
Drive these tools with a hammer to expand anchors.
An adjustable stop allows you to set anchors at consistent depths. Use with a hammer.
The fastest way to install shallow-hole female-threaded anchors. Just push the tip of the tool into the anchor and turn the tool with a power drill.
Also known as double expansion anchors, these expand from both sides for full contact and a secure hold.
Drive these tools with a hammer until the thicker portion of the tool makes contact with the anchor, causing it to expand.
These 316 stainless steel anchors have excellent resistance to chemicals and salt water.
Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.
Also known as drive rivets, install these anchors by hammering the pin into the body. Pry out the pin to remove.
These anchors are also known as drive rivets. To install, hammer the pin into the body. Pry out the pin to remove.
Also known as drive rivets, install by hammering the screw into the body. Unthread the screw to remove.
These anchors are also known as drive rivets. To install, hammer the screw into the body. Unthread the screw to remove.
Use in applications requiring high strength.
A tamper-resistant nut prevents unwanted removal of the object you are anchoring.
Also known as tap-in or uni-tap rivets, these anchors are barbed to resist pull out. Made from nylon, they're chemical resistant.
A hex head allows for a secure grip with a wrench.
Bolts are beveled under the head for a flush finish in countersunk holes.
Turn the bolt to expand the nut for a secure hold in concrete. These anchors are often used to anchor machinery.
These stud-style anchors include a nut and a washer.
A pivoting toggle bar creates a strong hold.
For narrow holes and small cavities where toggle anchors won't fit.
Used with adhesive in bricks and hollow blocks, such as cinder blocks, these mesh tubes create a stronger hold for rods and studs than other anchors.
These stud anchors strengthen the parts of buildings where steel framing connects to concrete. They’re also known as Nelson studs.
18-8 stainless steel anchors have good chemical resistance.
High-strength toggle anchors provide an extremely strong hold and stay in position when a bolt is removed.
Also known as Tapcons, use these screws in applications requiring high strength.
These blue and silver ultra-corrosion-resistant coated steel screws stand up to wet environments.
These 410 stainless steel screws are more corrosion resistant than ultra-corrosion-resistant coated steel screws.
Attach the components of these sets onto a hammer drill to install tapping screws in concrete, block, and brick.
Wedge these hangers in concrete and other solid materials.
Also known as Tapcons, these screws are often used to anchor parts to concrete, block, and brick. Assortments include a drill bit.
Use these bits with handheld power drills, drill presses, and hammer drills.
The SDS-Plus shank has two deep slots and two shallow slots for use with SDS-Plus-drive rotary hammers.
Insert these bits directly into power screwdrivers, impact drivers, and other tools that accept 1/4" hex shanks.
These bits have a round or hex shank that fits into the three-jaw chuck on a hammer drill.
These bits allow you to easily switch to another size by changing only the bit body. They are hollow and cut with their outside edge for drilling holes larger than 1 1/2" in diameter.
Drill holes up to 1 1/2" in diameter.
Also known as A-taper bits, these fit rotary hammers with a taper-shank chuck.
These hollow bits cut with their outside edge for drilling holes larger than 1 1/2" in diameter.
The 1/4" hex shank allows these bits to be used with standard impact drivers.
A more controlled chip removal reduces heat buildup. Use these bits on brittle material such as block and brick.
Use these diamond-coated hollow bits for wet drilling of masonry, concrete, and rebar with a drilling rig.
A built-in stop ensures repeatable drilling depths for installing drop-in anchors.
The SDS-Max shank has three deep slots and two shallow slots for use with SDS-Max-drive rotary hammers.
Unlike traditional wire-installing drill bits, you do not need to strip the end of the wire when using one of these bits. After drilling, insert the wire into the bit's hollow shaft and pull through the hole.
A more controlled chip removal reduces heat buildup. Use these bits on brittle materials such as block and brick.
Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules.
These kits include adhesives, applicators, and mixer nozzles.
Permanently set threaded rods, studs, and rebar in concrete.
When concrete is saturated or submerged in water, use these adhesives to form strong bonds.
Bond new concrete to old concrete, or use this adhesive as a primer on concrete surfaces.
These adhesives maintain their strength at temperatures up to 250° F.
Rails are drilled with consistently spaced holes for multiple mounting options that do not require machining. Use this steel bolt-together framing to build guards, tables, and racks.