S-shaped handles keep your hand clear of material, so you can cut flush against flat surfaces.

Prevent snags and injury with the rounded points on these small scissors.

Trim flush against a flat surface with the curved blades on these small scissors.

For extra leverage to cut through Kevlar, metal, and plastics, these scissors have long handles and short blades.

Insulated handles protect against shock from accidental contact with live electrical circuits. These scissors are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Protect sensitive equipment from harmful static discharges while cutting and stripping wire.

Keep your hand away from the material being cut.

The handles are angled 90° from the blade so you can cut material from directly above tight spaces.

Make straight and curved cuts in sheet metal—these sets come with three tools for different cutting patterns. Also called aviation snips, they have a double hinge, so they cut with more force and require less effort to squeeze the handles than standard sheet metal cutters.

Prevent waste from flying up as you work. A double blade makes two cuts to create a 7/64"-wide step that peels back, leaving little distortion and smooth edges.

Also known as bulldog snips, these have long handles and short blades for cutting through thick sheet metal with less effort than standard sheet metal cutters.

Blades are tapered to give you more control when cutting straight lines, tight curves, and circles, and they're serrated to prevent slipping. These cutters are also known as duckbill snips.

Loosen a few screws to swap dull blades with new ones. These cutters have offset handles to keep your hands clear of the metal being cut.

Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.

Use to cut patterns in flat material with minimal material loss and less effort compared to manual cutters.

Minimize material loss and edge distortion with these scissor-like cutters that cut metal up to 1/64" thick.

Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

These nibblers punch small pieces out of material to create an almost burr-free cut with no material distortion.

Make long, straight cuts around your facility—these cutters have a 12" blade and are light enough to move from bench top to bench top.

This large-capacity cutter has a 25" blade for long, straight cuts.

Turn your workpiece while cutting to create curves and complex shapes.

Use these one-handed cutters on small-diameter aluminum and copper power and communication cable.

Push the button to cut aluminum and copper power and communication cable.

Jaws ratchet to increase cutting pressure as you open and close the handles.

Make accurate, flush cuts through small wire with these tweezer-style cutters.

Plastic-cushioned grips make these cutters easy to hold during repeated cuts.

The carbide-tipped steel jaws stay sharp longer than standard steel jaws. You can sharpen them as they wear. These cutters have a double hinge that provides high cutting force with low gripping pressure.

Shaped like tweezers, these cutters make accurate, flush cuts in small wire without damaging the surface underneath. The grips drain static away from the tips, protecting sensitive components from electrostatic discharge (ESD).

These powerful cutters make diagonal cuts with a nipping action to cut extra-hard wire with ease.

An angled cutting head keeps handles up and out of the way for trimming bolts, chain, and wire against flat surfaces. Smaller than standard bolt cutters, these cutters can be used one-handed in tight spaces.

Keep a variety of small cutters on hand for cuts in tight spaces.

Leverage points on the jaws and handles let you cut through bolts, chains, and rods with 30% less effort than standard bolt cutters.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Slice through bolts and chain with low effort.

Cutters have double hinge that provides high cutting force with low gripping pressure.

A small grip enables one-handed cutting.

Use the lever to make one-handed cuts with minimal material distortion. Cutter mounts to a workbench for extra stability and ease of use for repeated cuts.

Make clean cuts on threaded rod with the pull of a trigger.

Two-handed strap cutters give you more leverage than one-handed strap cutters.