About twice as strong as aluminum rivet nuts, these steel rivet nuts are zinc plated for mild corrosion resistance.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

Wedges under the flange lock the nut in place in soft materials such as brass and aluminum.

These kits include one size of low-profile rivet nuts.

These low-profile rivet nuts are one-third the weight of steel and have mild corrosion resistance.

These rivet nuts are mildly corrosion resistant.

About twice as strong as aluminum rivet nuts, these rivet nuts are zinc plated for mild corrosion resistance.

Once installed these rivet nuts have a large back flange that distributes the load across a broad area for a strong hold in plastic and composites.

A PVC foam seal under the flange keeps liquids and gasses from leaking between the nut and the surrounding material.

A smooth base provides more contact with the mating surface than weld nuts with projections.

Weld these nuts to stainless steel surfaces.

Projections on the base concentrate the weld and provide room for heat to dissipate.

These nuts can be used in channels and tight spaces where round-base weld nuts won't fit.

Weld these nuts to stainless steel surfaces.

Weld these nuts to flat and uneven uncoated steel surfaces for a strong permanent hold.

You can weld these metric nuts to flat and uneven uncoated stainless steel surfaces for a strong permanent hold.

Threads float inside the retainer so you can install a bolt at a slight angle to align with off center parts.

These nuts have three mounting holes to accept screws and rivets for use with thin materials.

About half the strength of medium-strength steel coupling nuts, these metric nuts are for light duty fastening applications.

Made from brass, these inserts are electrically conductive, nonmagnetic, and have good corrosion resistance.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.

These 18-8 stainless steel inserts have better corrosion resistance than aluminum inserts and may be mildly magnetic.

The barbed sides keep these securely in place even before a screw is installed.

Install these inserts into plastic parts to create a secure base for fasteners.

The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

The flange keeps these inserts from being pulled through a hole and provides a load bearing surface.

Assortments include various sizes of tapping inserts for softwood.

These 18-8 stainless steel inserts have excellent resistance to chemicals and may be mildly magnetic.

Steel inserts have high strength for durability.

These 18-8 stainless steel tee nut inserts have better corrosion resistance than zinc-plated steel tee nut inserts.

Fewer prongs than other tee nut inserts reduce the risk of splitting hardwood—these inserts have three short prongs.

Use where vibration is a concern—these tee nut inserts have distorted threads that lock screws in place.

An open end allows long screws and bolts to pass through the insert.

Mount these inserts flush or below the material's surface.

A black-phosphate finish provides mild corrosion resistance.

These inserts are the most corrosion-resistant thread-locking inserts we offer.

These assortments include various sizes of thread-locking inserts.

A black-phosphate finish provides mild corrosion resistance.

These inserts are made to stringent military specifications.

Forming the strongest hold of any of our threaded inserts, these inserts have a distorted internal thread to lock screws into place and keys that drive into surrounding material to prevent slipping and rotating.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

These inserts have a high strength-to-weight ratio and resist acids and salt water better than nickel alloy and stainless steel inserts.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

A distorted thread grips the screw to resist loosening.

Inserts come with a through-hole tap and installation tool.

A dry film keeps the screw from sticking or binding in these inserts during installation.

These kits have short-, normal-, and long-reach inserts, an installation tool, and a tap.

Press these inserts into a drilled hole and the flexible metal teeth anchor them in the material. Use them with carbon fiber, fiberglass, and garolite.

A ribbed-shaped body holds the nut in place so it won't move when tightening a screw. Assortments contain rivet nuts, mandrels, nosepieces, and a plier-style installation tool.

Screw and nut sets or nuts secure brackets and other accessories to rails.