The slim head fits into tight spaces and around thin fasteners.

One head is angled for access to hard-to-reach fasteners. These are also known as ignition wrenches.

These lightweight tools are also known as AN (Army-Navy) wrenches.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

Also known as alligator wrenches and water-meter nut wrenches, the V-shaped head fits multiple hex fastener sizes.

Also known as spud, structural, and construction wrenches, use the pointed end of the handle to align bolt holes during assembly.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

These lightweight tools are also known as AN (Army-Navy) wrenches.

When turning fasteners in small spaces, these short wrenches fit where others can't.

Fit the narrow head into tight spaces and around thin fasteners.

Reach nuts obstructed by a fluid line or other barrier with these wrench heads.

Attach one of these heads to your square-drive ratchet or torque wrench to extend its reach or to access spaces with limited vertical clearance.

The hex shape achieves the best possible grip on hex fasteners to prevent rounding their points.

These short sockets fit spaces where height clearance is limited.

Pair these sockets with a bolt-through ratchet wrench to reach nuts at the bottom of a long threaded rod or bolt which can pass through the socket and the head of the wrench.

Designed for use with stainless steel fasteners, these sockets are more corrosion resistant than steel sockets and less likely to flake.

Eliminate the risk of your socket falling while reaching into your workspace with these flex sockets that have an integrated extension.

With a plastic insert, these sockets firmly grip hex nuts and bolts without rounding them or scratching highly polished finishes.

Quickly position these sockets on square and external 8-point fasteners.

Slip these slotted sockets onto wing nuts to tighten or loosen them with more force than fingers can apply.

These sockets fit the nuts found on water and gas valves.

Turn multiple shapes and sizes of fasteners with a single socket.

The opening is designed to grip threaded rod for quick installation and removal without damaging the threads.

A rubber insert grips the plug to prevent damage.

Achieve the best possible grip on hex fasteners and prevent rounding.

Move from lug nut to lug nut with the speed of a racecar pit crew. Up to five standard 6-point lug nuts stack up in the shank of these sockets, so you don’t have to stop to take the lug nuts out of the socket.

With a smaller OD than standard sockets, these fit between tightly spaced fasteners.

Attach these sockets to your spline-drive impact wrench.

The square shape provides the best possible grip on square fasteners and prevents rounding.

The slotted shape of these sockets fits over wing nuts to tighten and loosen them with more force than you can by hand.

Quickly position these sockets on square fasteners.

Pivot the head to access fasteners from an angle.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These sockets are designed to tolerate continuous use with power tools and impact tools in high-volume production and assembly.

Grip the indentations around the outside of tri-groove fasteners.

Access 6-point nuts and bolts in tight and awkward spaces—the heads on these sockets pivot.

Two spring-loaded balls inside these sockets firmly hold nuts and bolts in place as you turn them, including nonmagnetic fasteners like stainless steel screws.

With more than double the clearance of standard sockets, the sockets in these sets access nuts on extra-long bolts.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Shaped and sized for compatibility with wheel bearing locknuts on trucks and trailers, the sockets in these sets make it easy to install and remove locknuts.

With twice as many corners, 8-point sockets grab onto square-drive screws and nuts more quickly than 4-point sockets.

These sets organize what you need when working around live electrical circuits.

Suitable for occasional maintenance work, these sets are imported.

Reach nuts obstructed by a fluid line or other barrier with the wrench heads in these sets.

Connect one of the heads in these sets to a socket extension to reach an obstructed fastener, then turn the fastener without removing and repositioning the wrench head.

Remove and install dual wheels on trucks and trailers with the sockets in these sets.

Turn square-drive fasteners in several sizes with these socket sets.

Pivot the head to access fasteners from an angle.

Tighten or loosen nuts and bolts without damaging the finish.

Made of aluminum-bronze, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

When the ratchet head becomes worn or damaged, change it out for a new one.

Pair these wrenches with a bolt-through socket to reach nuts at the bottom of a long threaded rod or bolt which can pass through the head of the wrench.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

The shaft on these wrenches extends and locks.

The handle is covered in rubber for a comfortable grip.

Turn sockets in the most confined spaces.

Pivot the head to access fasteners in tight spots.

Use these tools for general shop applications.

The jaws on these wrenches are shaped to turn slip nuts, jam nuts, and large hex nuts.

Also known as a basin wrench, this tool has a pivoting head and spring-close jaws for working in tight spaces where it’s difficult to adjust a traditional wrench.

These tools have the heavy duty handle and adjustment mechanism of a pipe wrench and the smooth jaws of a traditional adjustable wrench.

The handle is covered in plastic for a comfortable grip.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.

A plastic-covered handle provides a comfortable grip.

Also known as spud, structural, and construction wrenches, the pointed end of the handle aligns bolt holes during assembly.

Turn fasteners with the firm grip of a wrench and the adjustability of pliers.

The handles are covered in plastic for a comfortable grip.

Made of materials that are Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

An extra-long handle provides access to hard-to-reach fasteners and increases leverage.

Flip these wrenches over to ratchet in the opposite direction.

Pivot the box end for access to fasteners in tight spots.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

These wrenches are made of stainless steel for excellent corrosion resistance.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Flip these wrenches over to ratchet in the opposite direction.

Suitable for occasional maintenance work, these sets are imported.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

An extra-long handle provides access to hard-to-reach fasteners and increases leverage.

The 25° offset heads give you additional clearance to turn hard-to-reach fasteners.

Also known as half-moon and obstruction wrenches, the shape lets you reach around obstacles and into machinery.

Also known as slugging wrenches, strike the handle with a hammer to break stuck fasteners free.

The head is offset 45° to provide clearance for reaching over obstructions.

The long handle provides extra leverage—add an extension to increase it even more.

These wrenches are polished for a mirror-like finish.

The heads are offset to provide clearance for reaching over obstructions.

Fit these wrenches into slots on the circumference of collars, bearings, and other machine tool components.

The head pivots to accommodate a range of diameters.

These wrenches are made of stainless steel for excellent corrosion resistance.

Made of stainless steel, these wrenches have excellent corrosion resistance.

The slim profile fits the flanges and nuts on the backing pads of portable sanders and grinders.

Reverse the pins when you need to fit different hole sizes on the face of collars, bearings, and other machine tool components.

Change out the pins to fit a different hole size.

The head pivots to accommodate a range of diameters.

The head pivots to accommodate a range of diameters.