Extend your reach in hard-to-access areas—turn these valves on and off using a square ratchet to grasp the hole at the end of the handle. They are full port, so they do not restrict flow.

316 stainless steel valves are more corrosion resistant than bronze valves.

Fix lockable lever handles in place using a padlock (not included).

Valves with a grease fitting have a built-in lubrication point. Inject lubricant for smooth operation and an extended service life. You can also remove the fitting to drain excess fluid from your valve.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

Rated for at least three times the pressure of standard threaded valves, these valves are used to start and stop the flow of compressed gas, pressurized water, or steam.

Lever handles are easy to open and close—they give you the most leverage of any handle type. Lockable lever handles can be fixed in place using a padlock (not included). 316 stainless steel valves are more corrosion resistant than steel valves.

Standard-port valves slightly restrict flow.

With a three-piece bolted body that disassembles for access to internal components, you can clean and repair these valves without unthreading them from your line.

Bronze valves resist corrosion from salt water and cleaning solutions used in machinery.

Steel valves are stronger and more durable than bronze valves for a longer service life.

316 stainless steel valves are more corrosion resistant than bronze or steel valves.

Lever handles are easy to turn and show the valve’s position. Lockable handles can be fixed in place using a padlock (not included).

Valves with actuator mounts can be equipped with air-powered or electric actuators using the mounting holes. This allows you to switch them from manual to automatic operation.

PTFE seals are the best choice for valves that are opened and closed often. The PTFE material forms a seal while remaining slippery, so it resists wearing down and failing with repeated use. Glass-filled PTFE seals resist expansion from water and heat. They’re ideal for systems that connect to heaters or hold fluids for extended periods.

Full-port valves do not restrict flow.

Maintenance kits include everything needed to replace the packing, seals, and seats on your valve.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

T-handles resist accidental movement when snagged or bumped.

Full-port valves do not restrict flow.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

A threaded union on these valves makes them easy to install and remove without disrupting your line. They’re a good choice for lines that require frequent maintenance or cleaning. They thread together or apart with only a turn to the union fitting, unlike other threaded on/off valves that require repositioning your pipe or valve. The union fitting slides over your pipe, and the threaded fitting sits inside. With a full port, these valves won’t restrict flow.

Made of plastic, they last longer than metal valves since the inside won’t corrode or pit. They’re also lighter in weight. PVC valves are commonly used in water lines. CPVC valves handle higher temperatures than PVC or polypropylene valves. They’re the best choice if your system connects to a heater.

Valves with a T-handle have a larger gripping surface than valves with a short lever handle, so they’re easier to turn when your hands are slippery.

Bolt these valves to ANSI flanges. Their lockable lever handle can be fixed in place using a padlock (not included). All have four mounting holes to install an actuator, so you can convert them from manual to automatic valves.

Steel valves stand up to corrosion better than cast iron valves. 316 stainless steel valves are more corrosion resistant than cast iron and steel valves.

Full-port valves do not restrict flow.Pressure class 150 valves are standard and work for most low-pressure applications.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

Also known as wafer ball valves, these combine the slim body of a butterfly valve with the high flow rates of a flanged ball valve. Bolt these valves to ANSI flanges—they meet ASME standards for dimensions, material, and pressure-temperature rating. They are full port, so they do not restrict flow.

316 stainless steel valves are more corrosion resistant than steel valves.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

Clean and maintain these valves without removing welded connections. To create a permanent, leak-tight connection, insert unthreaded pipe into the socket and weld. These valves have a three-piece bolted body that disassembles inline, which makes it easy to access internal components. They also have lockable handles that can be fixed in place with a padlock (not included). All are full port, so they do not restrict flow.

316 stainless steel valves resist corrosion better than steel valves.

Lever handles make it easy to see if the valve is open or closed.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

Maintenance kits (sold separately) include seats, seals, and stem packing to replace worn parts inside valves.

Streamline your installation and removal process. These valves give you the leak-tight permanent connection of a socket connect with the ease of fittings that come apart. Before you install the valve, slide the union fitting over your pipe, then insert the pipe into the socket fittings and bond with primer and cement. The union fittings allow the valve to be quickly removed where other socket-connect valves would require you to cut your pipe. A fluoroelastomer seal and plastic body withstand aggressive and corrosive solutions in chemical-processing applications. All valves have a T-handle that resists accidental movement when snagged or bumped. They are full port, so they do not restrict flow.

PVC valves are often used in mild chemical processing systems. CPVC valves resist heat better than PVC valves, so they’re a good choice for systems that connect to a heater. Lockable T-handles can be fixed in place using a padlock (not included).

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves meet NSF/ANSI 61, which means they’re safe to use with drinking water systems. They are full port, so they do not restrict flow.

PVC valves are made of the standard material used in most drinking water systems. CPVC valves resist heat better than PVC valves, so they’re better for water systems connected to a heater.

T-handles resist accidental movement when snagged or bumped.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

Ideal for lines that need frequent maintenance, these valves have union fittings that disassemble quickly for removal. To install, slide the union fitting over unthreaded pipe. Insert the pipe into the socket fitting and bond with primer and cement (both not included) to create a permanent, leak-tight connection. When you need to remove the valve, just unthread the union fitting. These valves meet NSF/ANSI 61 for use with drinking water. All have a T-handle that resists accidental movement when snagged or bumped. They are full port, so they do not restrict flow.

PVC valves are made of the standard material used in most drinking water systems. CPVC valves resist heat better than PVC valves. They’re the best choice if your system connects to a heater.

Fix lockable T-handles in place using a padlock (not included).

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

Also known as gate valves, these valves gradually open and close to prevent system damage from suddenly starting and stopping flow.

Valves with a pull handle open and close faster than valves with a wheel handle. Also known as slide valves, they’re often used to control flow in air conditioning and ventilation systems. Valves with a wheel handle open and close with multiple turns, providing more controlled, shock-resistant flow than valves with a pull handle.

Valves with a rising stem lift the handle as they open and lower it as they close. At a glance, you can see if flow is on or off. The stem is isolated from what’s flowing through your line, giving these valves a longer lifespan than valves with a nonrising stem. Valves with a nonrising stem keep the stem in the same position whether they’re open or closed. They’re often used underground and in low-clearance locations.

Valves with threaded union stem allow you to maintain and repair these valves while they’re still inline—you can disassemble the stem so there's no need to unthread the pipe connections. Bronze valves resist corrosion better than brass valves. They’re also stronger.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

Maintain and repair these valves while they’re still inline—you can disassemble the stem so there's no need to unthread the pipe connections. Also known as gate valves, they open and close gradually to prevent sudden starts and stops. Control the flow by turning the wheel handle multiple times. This gives you more control than a pull handle. Made of bronze, these valves have good corrosion resistance.

Valves with a rising stem lift the handle as they open and lower it as they close. At a glance, you can see if flow is on or off. The stem is isolated from what’s flowing through your line, giving these valves a longer lifespan than valves with a nonrising stem.

Easier to install and remove than threaded or weld-on valves, these valves bolt to flanges. They’re often used in lines requiring frequent cleaning and maintenance, such as those for slurries. They open and close gradually, preventing system damage from sudden starts and stops in flow. Also known as gate valves.

Valves with a wheel handle open and close with multiple turns, providing more controlled, shock-resistant flow than valves with a pull handle.

Valves with a nonrising stem keep the handle in the same position whether they’re open or closed. They're often used in low-clearance locations. Valves with a rising stem lift the handle as they open and lower it as they close. At a glance, you can see if flow is on or off. The stem is isolated from what’s flowing through your line, giving these valves a longer lifespan than valves with a nonrising stem. This makes them good for critical lines and lines that need to be opened and closed frequently.

Cast iron valves are stronger than steel valves but more brittle than steel, ductile iron, and stainless steel valves. Steel valves resist impact better than cast iron valves.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

FM-approved, these valves are often used to isolate sections of your facility’s water supply for fire suppression and protection. They bolt to flanges for easier installation and removal than threaded or weld-on valves. This makes them a great choice if you have to clean and maintain your line frequently. Also known as gate valves, they open and close gradually to prevent sudden starts and stops of flow that could damage your system. Epoxy coated, these valves resist corrosion. They’re bright red, so they’re easy to identify as fire valves.

Their rubber-coated gate, also known as a resilient wedge, compresses against the valve for a long-lasting, leakproof seal. It seals tightly even if you install these valves vertically, or if there’s low back pressure. For easy disassembly during maintenance, they have a flanged stem housing that bolts in place. However, the housing makes these valves heavier and larger than valves with a threaded or welded stem housing.

Valves with a wheel handle open and close with multiple turns for controlled, shock-resistant flow. Valves with a rising stem lift the handle as they open and lower it as they close. At a glance, you can see if flow is on or off. The stem is isolated from what’s flowing through your line, giving these valves a longer lifespan than valves with a nonrising stem. This makes them good for critical lines and lines that need to be opened and closed frequently.