Illuminate outdoor areas and objects such as parking lots, flag poles, and billboards.

Light up entryways and paths alongside your building for safe travel after dark. These lights are also known as wall packs.

No need for wiring—these lights plug-in with a three-prong plug.

Illuminate entryways and walkways at night—these lights shine when they detect motion. Powered by the sun, they can be installed where you don’t have access to electricity.

Startle intruders and draw attention to activity in remote areas without access to power—these solar-powered lights shine bright when motion is detected. They charge during the day, and the battery lasts all night with typical activity.

These lights are UL listed for use in hazardous locations where flammable/combustible gases, vapors, and liquids may be present.

Point these lights toward paths, doorways, and other dark areas. Since they run on batteries, you can skip the hassle of running wires.

Bring light to your parking lot or walkway in minutes—these lights come wired and already attached to a lightweight pole.

Guide pedestrians and drivers at night with lighting that defines paths and driveways. These lights produce ambient illumination without the glare of overhead lights.

The enclosure on these jelly jar lights contains explosions, sparks, and flashes. These lights are safe to use in NEC Class I, II, and III, Division 1 hazardous locations.

Illuminate chemical plants, refineries, and other facilities where flammable and combustible gases may be present in the event of a leak or ventilation failure. These lights are rated for use in NEC Class 1, Division 2 hazardous locations.

Safely light up chemical processing plants, mining operations, and other large areas where combustible gases and dust are present. These lights have an explosion-proof housing that contains sparks and flames, so they won’t react to nearby hazards.

Upgrade your existing hazardous location bay lights to energy-efficient LEDs.

Tough enough for offshore rigs and seafaring vessels—yet less than half the height of typical jelly jar lights. Built with a thick aluminum housing and a tough polycarbonate lens, these lights withstand hard impact without a guard.

Light up spaces that have no electrical connection or are difficult to wire, such as sheds and closets.

Upgrade your old fixtures to energy-efficient LED lights. These kits replace the need to maintain hard-to-find-bulbs and ballasts, or replace the entire fixture.

Powered by the sun, these lights illuminate outbuildings, shipping containers, and other remote places that lack electricity.

Brighten entryways and small spaces.

Wire these lights end-to-end to create long rows that brighten indoor workspaces such as offices and workshops.

Install these lights into ceiling cutouts with housings for direct, overhead lighting. They’re often used in indoor spaces such as offices and lobbies, and as decorative lighting.

Create long rows of lights in indoor workspaces without having to hardwire one unit to another.

Install these lights flush with your ceiling for a smooth look and even lighting. They offer the appearance of can lights without the bulky housing.

Often used in stairwells and hallways, these lights save energy by only turning on when they sense movement.

Illuminate steps to reduce the risk of tripping or falling, especially at night or in poorly lit areas.

Rated for over a decade of use well above 100° F, these linear bay lights long outlast standard facility lights in high heat.

Illuminate harsh, wet areas, even outside in extreme weather—these lights are often used on ship building ports. Rated NEMA 4X and UL marine listed, they’re sealed against heavy rain and washdowns, and they won’t corrode from salt water or other liquids.

Upgrade your traditional fluorescent washdown lights—these LEDs last longer and eliminate the need to replace bulbs.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust.

Prevent contaminants from entering your ISO Class 3 clean room—these lights have an airtight seal.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

Pop these lights on magnetic surfaces to brighten wet spaces. Rated NEMA 6 and ETL listed, you can splash, spray, or dunk them in water, and they’ll keep working.

Power these lights with the same battery as your other cordless tools. They run on a Milwaukee M18 battery to light up work where there’s no outlet.

From pipes to pallet racks to control panels—these lights clamp onto almost anything and swivel to direct light just where you need it.

Splashes and drips are no problem for these lights. They don’t need an outlet, so you can bring them wherever you need them.

Flood hazardous areas with light—these lights are intrinsically safe, meaning they can’t cause an explosion or fire. Rated NEC Class I, II, III, and Zone 0, they’re safe to use in areas with ignitable concentrations of flammable or combustible gases, dust, and fibers.

Safely light up large spaces where combustible gases and dust are normally present. Rated NEC Class I and II, these lights have a housing that contains any sparks or flames and seals out ignitable gases, vapors, and dust.

Flood dark, remote jobsites with multiple tiers of light. These cordless lights stack on top of each other to focus a strong beam of light in one direction.

Brighten remote areas, even if they’re damp or rainy. These floodlights are IP rated to keep out humidity and dripping, splashing, and falling liquids.

Compact and easy to carry, these ETL listed lights stand up to dripping, splashing, and falling liquids. The head adjusts up and down to direct light where it's needed.

Raise, lower, and tilt these lights to brighten your work in wet spaces.

Brighten remote spaces with the DeWalt rechargeable battery that’s already in your toolkit. These floodlights extend up to 7 ft., and the light head turns at any angle to aim light where it’s needed.

As bright as stadium lights, these floodlights are the most powerful in our offering—they’ll brighten jobsites half the size of a football field. They run on a diesel generator you can use to power other lights and tools in the field.

A gasket seals the enclosure of these backup lights from washdowns.

Expand the reach of emergency backup lights. These add-on heads are often used to extend emergency lighting into stairwells, exits, and other remote areas.

Install these lights in aircraft hangars, gas plants, and other facilities where flammable and combustible gases or dust may be present, such as leaks or ventilation failures. Rated NEC Class I, Division 2, they seal out gases but aren't built to contain explosions.

With a smooth, shatterproof lens, these lights have no crevices where debris can accumulate. Their stainless steel connectors, plastic lens, and mounts resist acids, alkalis, and other chemicals commonly used in food environment washdowns.

Illuminate machines and monitor processes where flammable and combustible gases, dust, or fibers are present—from paint spray booths to chemical plants. These lights have an enclosure that contains sparks, flashes, and explosions.

Update conventional fluorescent tubular lights with newer LED technology. These lights match the diameter of most older lights and fit existing brackets without the need to drill new mounting holes.

Signal machine status with changing colors—green for running, yellow for standby, red for stopped—then switch to a bright white light to illuminate maintenance or tool changes. Using your programmable logic controller (PLC), you can adjust the brightness of these lights and mix red, green, and blue light to achieve thousands of colors.

Illuminate machines or monitor processes in areas where flammable or combustible gases may be present, such as during leaks or ventilation failures. These lights are rated for use in NEC Class 1, Division 2 hazardous locations.

As chips fly and coolant splashes, these lights shine bright in tough machining conditions. Use them to light up your CNC machine for everything from tool swaps to tune-ups.

Pivot the head to cast a narrow beam of light to exactly where it's needed.

Shine light on machinery and through the sight glass on tanks to inspect food, brewery, chemical, pharmaceutical, and bio-tech processing lines.

Safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust, these lights are rated NEC Class I, II, and III.

With built-in LEDs, these lights deliver all the brightness of larger dock lights in a low-profile design. A hinge stop keeps the arm from extending past the dock door, and the curved design fits around the track.

Illuminate small spaces and mark locations with these reusable lightsticks.

Shine light into hard-to-reach spaces with these flexible-arm flashlights.

Clip these little flashlights to a baseball cap or a surface to light up your work.

IP rated for submersion, these flashlights keep working even if dropped in water. They run on a rechargeable battery, saving you the hassle of frequent battery swaps.

Always have a light handy. These flashlights use disposable batteries, so you can swap in a new set at any time without waiting for a charge.

Have light at the ready in the wettest conditions. These flashlights are IP rated for submersion, so they’ll keep working even if dropped in water.

When the power goes out, these flashlights automatically light up. The head tilts so you can aim light wherever you need it.

Instead of making frequent battery swaps, just plug these flashlights in to charge them.

Because these flashlights are buoyant, they're easy to recover when dropped in the water.

Clip these little flashlights to any surface up to 1/2” thick and keep your hands free for work. They’re rated for use in environments where ignitable concentrations of flammable or combustible gases, vapors, and liquids are present.

Tilt the head on these flashlights to point light where you need it in explosion-prone areas. Rated NEC Classes I and II, they’re safe to use where there are ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.